Question about 1984 Ford F 150

1 Answer

Won't run right and i am not sure if it is the distributor or wires or what? the engine is a 300 6 cylinder. appreciate the help

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 42 Answers

A full tune-up should disclose the problem.
Don't overlook the carburetor in that old-timer. Also, vacuum lines, fuel pump pressure, spark plugs, distributor points and condenser, ignition coil and bare wiring that may be short against something. Good luck, Paul

Posted on Sep 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2001 dodge ram 5.9 2500, engine was running sluggish, changed plugs wires, distributor cap, rotor cap, and crankshaft sensor, now vehicle won't start at all, I'm sure I have the wiring right


Recheck the plug wires. If they are right, put cylinder one on top dead center. pull the distributor cap. It should be where it is supposed to be or 180 degrees off(at number 6). If not there, someone has just moved the wires to make it run. Reset the distributor.

Sep 16, 2016 | Dodge Ram 2500 Cars & Trucks

1 Answer

Won't start


If it's backfiring through the intake, then more than likely it's a timing issue. The distributor cap has the cylinder numbers molded into it where the plug wires go... Make sure the wires are in the right spots. If that's good, then it's possible the distributor isn't lined up right.

May 10, 2013 | 2001 Chevrolet Chevrolet Blazer

1 Answer

Engine won't start


the spark plug wires can be confusing but a 4 cylinder is not that hard from the front of the engine being where the pulleys & belts are its 1,2,3,4 on the coil or distributor it can be in counter or clockwise rotation 1&3,2&4 or 1&4,2&3 likely its 1&3,2&4 hope you find this helpful

Mar 03, 2013 | Cars & Trucks

2 Answers

How to remove distributor on 1994 nissan pathfinder


Hi there:
Check this removal procedure (See Figures 1 through 5)

  1. Disconnect the negative battery cable.
  2. Unfasten the retaining clips (only remove the coil wire if necessary) and lift the distributor cap straight off. It will be easier to install the distributor if the spark plug wiring is left connected to the cap. If the plug wires must be removed from the cap, mark their positions to aid in installation.
  3. Remove the dust cover and mark the position of the rotor relative to the distributor body; then mark the position of the distributor body relative to the engine block.
  4. Detach the harness assembly connector.
  5. Remove the pinch-bolt and lift the distributor straight out, away from the engine. The rotor and body are marked so that they can be returned to the position from which they were removed. Do not turn or disturb the engine (unless absolutely necessary) after the distributor assembly has been removed.




6_26_2012_2_15_23_pm.jpg

Exploded view of the distributor assembly-6-cylinder engine




6_26_2012_2_15_51_pm.jpg

Align the mark on the housing with the mark on the shaft-VG30i and VG30E engines


6_26_2012_2_16_14_pm.jpg


After the distributor assembly has been installed, the rotor should be in this position-VG30i and VG30E engines


6_26_2012_2_16_40_pm.jpg

After the distributor assembly has been installed, the rotor should be in this position-KA24E engine



INSTALLATIONTiming Not Disturbed

  1. Insert the distributor in the block and align ALL matchmarks made during removal.
  2. Engage the distributor driven gear with the distributor drive.
  3. Install the distributor clamp and secure it with the pinch-bolt.
  4. Install the distributor cap and fasten the harness electrical connector.
  5. If necessary, install the spark plug wires and coil wire.
  6. Start the engine. Check the timing and adjust it if necessary.

Timing Disturbed
  1. It is necessary to place the No. 1 cylinder in the firing position to correctly install the distributor. To locate this position, the ignition timing marks on the crankshaft front pulley can be used.
  2. Remove the No. 1 cylinder spark plug. Turn the crankshaft until the piston in the No. 1 cylinder is moving up on the compression stroke. This can be determined by placing your thumb over the spark plug hole and feeling the air being forced out of the cylinder. Stop turning the crankshaft when the timing marks indicate TDC or 0 .
  3. Oil the distributor housing lightly where the distributor bears on the cylinder block.
  4. Install the distributor so that the rotor, which is mounted on the shaft, points toward the No. 1 spark plug terminal tower position when the cap is installed. Of course, you won't be able to see the direction in which the rotor is pointing if the cap is installed, so lay the cap on the top of the distributor and make a mark on the side of the distributor housing just below the No. 1 spark plug terminal. Make sure that the rotor points toward that mark when you install the distributor.

On the VG30i and VG30E engines, align the mark on the distributor shaft with the protruding mark on the housing.

  1. When the distributor shaft has reached the bottom of the hole, gently move the rotor back and forth slightly until the driving lug on the end of the shaft enter the slots cut in the end of the oil pump shaft and the distributor assembly slides down into place.

On the VG30i and VG30E engines, the distributor rotor tip should be in the 11 o'clock position.

  1. Fasten the distributor hold-down bolt.
  2. Install the spark plug into the No. 1 spark plug hole.
  3. Install the distributor cap and engage the harness electrical connector.
  4. If necessary, attach the spark plug wires and coil wire.
  5. Start the engine. Check the timing and adjust it if necessary.





Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day

Jun 26, 2012 | 1994 Nissan Pathfinder

2 Answers

I have a 2000 chevy s10 ZR2 4.3L V6. I had just replaced the intake manifold gasket. I went to start it up and have now developed a misfire in cyl 5. I have already put in new plugs and wires. I...


I have a 2001 Chevy s10 that I put an aftermarket air intake on. With high acceleration speeds, the car would lunge and stall. The engine would also quit. You need to make sure that you have no leaks in your intake manifold. If you have leaks in your manifold, your vehical will misfire. Check your air intake manifold by turning on your vehical on and running your hands up and down the air intake. If you feel air coming out, you have a leak. This needs to be corrected. I hope this helps! Please rate 4 thumbs up!

Apr 18, 2011 | 2002 Chevrolet TrailBlazer

2 Answers

1993 lexus 300 sc firing order and distributor cap diagram


Hello! If the engine in your vehicle is the 3VZ-FE...The firing order is 1-2-3-4-5-6...Distributor rotation is Counter Clockwise...

saailer_14.gif

If the engine is a 2JZ-GE...The firing order is 1-5-3-6-2-4...Distributor rotation is Counter clockwise

saailer_15.gif
Guru...........saailer

Nov 20, 2010 | 1992 Lexus Sc 300

3 Answers

I changed the spark plugs and wires on my chevy s10 2wd pick up, which is a 4 cylinder and now it will not turn over. I might have the wires mixed up on the distributer cap. Can someone show me a picture...


GET A PIECE PAPER DRAW A LARGE CIRCLE TOP UPPER HALF CIRCLE LEFT TO RIGHT WRITE NUMBERS 1 AND 3 BOTTOM HALF CIRCLE LEFT TO RIGHT RIGHT NUMBERS 2 AND 4 THAT YOUR DISTRIBUTOR SPARK PLUGS WIRES LOCATION.STANDING ON SIDE OF ENGINE WHERE DISTRIBUTOR IS LOOKING DOWN AT DISTRIBUTOR 1 AND 3 FIRST TWO SPARK PLUGS TERMINALS NEXT TO ENGINE. AND 2 AND 4 SPARK PLUGS TERMINAL ON CAP FACING YOU. THIS IS CYLINDERS LOCATIONS STANDING IN FRONT OF ENGINE.RUN WIRES FROM DISTRIBUTOR CAP TO PLUGS TO THE ENGINE SPARK PLUGS.

Oct 17, 2010 | Chevrolet S 10 Cars & Trucks

1 Answer

1995 Thunderbird LX 4.6 V8 Cylinder Location, Distributor Wires


Which ever plug you changed you need to follow that plugs wire to the dis. cap and that should be the wire. chrismoss

Apr 11, 2010 | 1995 Ford Thunderbird

2 Answers

Cannot start changing pugs and wires


Sounds like you have the firing order right but your off on the #1 on the distributer. Every time you get an explosion coming from the carb its misfiring. Find the #1 on dist and continue with firing order

May 24, 2009 | 1983 Chevrolet Silverado

Not finding what you are looking for?
Cars & Trucks Logo

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...