Question about Toyota Camry

Open Question

My 2005 Camry remote suddenly stopped working. I have tried my other remote and replaced the battery, but it still doesn't work. Neither the locks or the trunk work. Is it the receiver, the remote or what? I had to push the little red button to get the alarm to shut off the first time.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75797 Answers

SOURCE: 2005 cadillac sts remote transmitter

This is the procedure for a reprogram of the remote's from the factory service manual, if it doesn't work then u may have a receiver issue.
Use this Procedure for Vehicles with
Driver Information Center Buttons

This information is in your Owners Manual in the
Drivers Information Center Section.


1. Insert Key and turn to ON position so you can access Driver Information Center

2. Press the vehicle information button until
PRESS TO RELEARN REMOTE KEY displays

3. Press the set/reset button until
REMOTE KEY LEARNING ACTIVE displays

4. Press and hold the lock and unlock buttons on the first keyless remote at the same
time for approximatley 15 seconds. A chime will sound indicating that the remote is
programmed.


5. To program additional remotes at this time repeat step 3.
This vehicle can have a maximum of eight remotes programmed.

6. To exit programming mode turn key off and remove key.
Test remote(s).


Use this Procedure for Vehicles without
Drivers Information Center Buttons


To access this display, the vehicle must be in Park (P) with key in the on position (as far
as you can go without cranking engine)

1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays.
2. Press and hold the trip odometer reset stem for three seconds.
The message REMOTE KEY LEARNING ACTIVE will display

3. Press and hold the lock and unlock buttons on the first keyless remote at the same
time for approximately 15 seconds. A chime
will sound indicating that the remote is
programmed.

4. To program additional remotes at this time repeat step 3.
This vehicle can have a maximum of eight remotes programmed.
5. To exit programming mode turn key off and remove key.
Test remote(s).

Posted on Jan 17, 2009

  • 75 Answers

SOURCE: my remote door locks dont work with the remote

hi,problem with remote key,you check the battery of the transmitter,fine,how about trying with spare key,or check fuse or send to dealer for proper diagnose,preventing wrong part replacement.

Posted on Feb 20, 2009

lester482529
  • 226 Answers

SOURCE: 2003 Saturn ION 2 trunk Problem

there is a manual switch that is located near the trunk latch for a safty lockout it might have been switched by accident look to make sure.hope this helps.

Posted on Jun 21, 2009

  • 1 Answer

SOURCE: programming keyless remote

2003-04 Mazda 6 REMOTE PROGRAMMING


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the driver’s door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the driver’s door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1 twice. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) twice. Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done!

Good Luck.

Posted on Jul 10, 2009

  • 87 Answers

SOURCE: 2005 Nissan Altima electronic trunk latch does not

sounds like a bad connection on relay start there first do ya hear a click at all. if not check fuses. otherwise wiring would be where I would start

Posted on Aug 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Central locking 2005 subaru liberty stopped working on 2 doors


1. Replace battery in remote
2. Replace sensor at rhf door lock (it is inside of door)

Apr 30, 2014 | Cars & Trucks

1 Answer

2005 Nissan Sentra, the keyless entry locks the doors but does not unlock them.


does your unlock button work in car? If it does, do you have another keyless entry key fob? If so does it work? If you just replaced the battery you can try removing battery and cleaning contacts within remote. I know some of the nissan altimas had the same issue and the only solution was a new key fob. Good Luck

Jan 04, 2013 | 2005 Nissan Sentra 1.8

1 Answer

Vauxhall Astra's remote suddenly stopped working.


Start troubleshooting by redoing the "mechanic's" work, making sure that the correct and unblown fuses are in the correct places.

May 13, 2017 | Cars & Trucks

1 Answer

I unhooked the battery now i cant stop the horn and it wont start the remote key does not work it got washed in clothes help please.97 camry


Lock then unlock the doors with the power lock button, with all doors closed (key not in ignition). If this doesnt work, try again using the key to lock and unlock from the driver door, with all doors closed.

May 12, 2010 | 1996 Toyota Camry

1 Answer

Remote locking/unlocking device suddenly stopped working - battery change did Not fix the problem Is this a wiring issue? and if so where do I look? Car is a Ford Escape


take it to auto zone they will test if its still good if it is u may need to replace the battery on the romote or reprogram it to ur vechicle if needed to reprograming look at the thing were they connect the computer under the dash on the driver side then connect a wire from the 4th port and the 8th port the doors will lock and unlock signaling that the remote is ready to program then hold the lock key for 15 sec and your done

Apr 15, 2010 | 2005 Ford Escape

1 Answer

Remote key lock stopped working after wal mart put new battery in and now my head lights stopped workin!!!


check fuse for low beam, then possibly both low beam globes. they could have blown.
the key remote may need reprograming into system try put key in ignition in on position then press remote buttons a couple of times then try if no good need to go to dealer to be programed into system again or it needs repairing/replacing.

May 31, 2009 | 1996 Chevrolet Camaro

1 Answer

Remote key fob suddenly stopped work


Check out page 57 of the manual:

http://www.motorcraftservice.com/pubs/content/~WO6FOC/~MUS~LEN/41/06focog4e.pdf

If that doesn't work, it sounds like a trip to the dealer.

May 02, 2009 | 2006 Ford Focus

1 Answer

Need to reprogram door locks for 2004 Toyota Camry


I recently replaced the battery on my 2004 Toyota Camry. When I installed new battery the door locks will not stay unlocked once opened with remote. How do I reprogram?

Feb 21, 2009 | 2005 Toyota Camry Solara

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

317 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...