Question about 1993 Ford Ranger SuperCab

Open Question

How do i bleed rear brakes on 1993 ranger nothing is coming out

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

polarcycle
  • 1392 Answers

SOURCE: BLEEDING REAR BRAKES CAN BLEED ONCE THEN SECOND

Sounds like a problem with the proportioning valve. Try not to push the pedal down to far when bleeding. The valve sounds like it is getting stuck closed, and takes a little bit to release and allow fluid to pass again.

Posted on Jun 10, 2009

BigBlue77
  • 59 Answers

SOURCE: how to bleed brakes

Sounds like the proportioning valve is stuck. You may need to break a front bleeder loose and hit the pedal the unseat the valve. Then blead the rearbrakse and then bleed the wheel where you broke the bleeder loose. That should work.

Good Luck

Posted on Oct 12, 2008

emissionwiz
  • 75005 Answers

SOURCE: 1989 Ford ranger rear antilock light on rear brakes lock up

metal particles on the trigger wheel sensor of the rear differential case, this causes a loose of signal and the light to come on. also a broken tooth on the trigger wheel inside the diff can cause this or a dirty/corroded connection to the sensor from water intrusion.

Posted on Dec 19, 2008

junmag
  • 175 Answers

SOURCE: Rear brakes wont bleed. Sucks fluid in when brakes applied. Has ABS.

try this. open the two bleeder screw at the rear calipers. leave it open untill the fluid drips generously. close the bleeder. try the brakes. if it works bleed it the nornal way. note: make sure you dont run out of fluid in the master cylinder

Posted on Jun 02, 2009

  • 4336 Answers

SOURCE: bleeding brakes 2000 suburban wsith ab

Why were the brake lines replaced?

Sounds like the mastercylinder may have run dry. You have to bench bleed the master and then DO NOT allow fluid to run low, while bleeding brakes...

if master cylinder runs low on fluid and air gets in, almost impossible to bleed with out releasing the lines and bleed master it self.

Posted on Sep 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bleeding brakes on 1993 mercury topaz brake fluid comes out rt front wheel and only the left rear wheel


ive found the best method to bleeding brakes is to use suction and not pressure method , this way its sure that all the lines have fluid in them , vac pumps are the best way of doing this

Jan 14, 2017 | Mercury Cars & Trucks

1 Answer

Grease in rear wheel hub


The rear brake cylinders are located inside the hub with the brake shoes on drum brakes...(common in 2004 Rangers on rear only) The brake cylinders are a "wear item" with seals...we used to rebuild the cylinder with new seals...best today to buy new brake cylinders to replace the leakey ones...You will need to bleed all 4 brake line/wheel connections after the replacement. Hope this helps.

Oct 14, 2013 | 2004 Ford Ranger

1 Answer

1989 ford ranger, no fluid flows to bleed rear brakes. (has anti-lock brakes)


there is actually a trick that works most times, when you go to bleed the rear turn the key to on, the pump will allow the fluid out to the rear.

Sep 20, 2011 | 1989 Ford Ranger

1 Answer

Can bleed my brakes 1999 ford ranger 4x4


You will need a friend to help. Pick up an extra bottle of brake fluid that your vehicle manufacturer recommends. Open the bleed valve on the closest brake first. Have your friend gently push the brake pedal until fluid comes out bleed valve. Tighten bleed valve. Check your brake fluid tank and top up as needed. Work your way around the vehicle repeating this procedure.

Jul 16, 2011 | 1999 Ford Ranger SuperCab

1 Answer

Brake pedal often goes almost to floor-not spongy at all-doesn't seep if pressure constantly applied.


Hi,
Probably air in the brake system. Bleed your brakes thoroughly. Start with right rear, then left rear, then right front then left front. Maintain proper fluid level in master cylinder while bleeding. Brake pedal hieght comes from the rear brakes, as those are the longest brake lines in the system. Mike

Jun 14, 2011 | 1993 Cadillac DeVille

1 Answer

I'm leaking brake fluid in my the rear my truck


Hello rodeure
The brake fluid can leak from a few places in the rear. Bad wheel cylinder/brake hose or the most likely cause, a rusted brake line.
Fill the master cylinder and have somone step on the brake while you
look under the truck. When you find the leak, the best thing to do is to
replace the lines up to the front valve (they don't rot in one spot) then
bleed the brakes and you should be good to go. Hope this helps.

Jul 07, 2010 | 1993 Ford Ranger SuperCab

1 Answer

The brake cylinder in the rear drum of a 93 ford ranger broke, how do i replace it


Remove wheel, brake drum, and brake shoes. The cylinder is the part the brake line goes into and it spreads the brake shoes apart when you brake.

Loosen the brake line but do not take off, unbolt the cylinder and then disconnect brake line. loosely connect the brake line to the new cylinder so you do not loose much brake fluid, bolt new cylinder in and then tighten the brake line.
Reinstall shoes. There should be a bleeding screw/grease head in the brake cylinder, loosen this and have someone step on the brake to bleed the line, have them hold the brake while you tighten the bleed screw. Do this as many times as necessary until brake fluid only with no air comes out.
Reinstall drum and tire, top off brake fluid.

Mar 16, 2010 | 1993 Ford Ranger SuperCab

1 Answer

No brake fluid coming out of rear cylinders after bleeding brakes . why


do the brake fluid level go down? if it does its a leak in the system, if it does not, it could be a defective master brake cylinder

Jan 24, 2010 | 1989 Ford Ranger

1 Answer

Soft brake pedal


DON'T KNOW IF U DID BUT U NEED TO BLEED THE BRAKES IN THIS ORDER RIGHT REAR,LEFT FRONT ,LEFT REAR AND RIGHT FRONT.IF THAT DOES NOT HELP SOMETIMES U CAN ADJUST THE ROD BETWEEN THE BRAKE MASTER & BOOSTER.U HAVE TO REMOVE THE MASTER TO DO THAT.U MAY HAVE A BAD MASTER.

May 01, 2009 | 1993 Honda Civic 4 Door

2 Answers

Brakes not working


You need to adjust the rear brakes and you might have to bleed them out.

Mar 29, 2009 | 1988 Ford Ranger

Not finding what you are looking for?
1993 Ford Ranger SuperCab Logo

Related Topics:

348 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...