Question about 2001 Ford Windstar

1 Answer

Need to know the location of grease zerks - 2001 Ford Windstar

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 678 Answers

Your vehicle most likely didn't come with any greaseale joints from the factory. However given the age, there could have been parts replaced that now have fittings. So, without looking at the vehicle it'd be impossible to tell which joints are greasable. But, the parts that could have a zerk fittings on your van include the outer tie rod ends, and lower ball joints. So just take a look and grease where appropriate.

Posted on Sep 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Does a mazda 2006 have grease zerks


Check your vehicle's owner's manual service guide; contact the service or parts dept at a local Mazda dealership; visually (look) at the steering linkages, or call your local auto parts store...I know that some models have sealed units with no lube points and others that have lube points...the consideration is model and are the steering components stock or aftermarket?

Mar 22, 2015 | Mazda Cars & Trucks

1 Answer

Where are the grease zerk locations


On most newer cars there are no zerk fittings.

Aug 04, 2014 | 2000 Chrysler LHS

1 Answer

How many and where are all grease zirk fittings on my 1997 lumina 4door,A/T 3.1 litre


Unless the outer tie rods or lower ball joints have been replaced than there will not be any grease zerks. If the outer tie rods have been replaces the zerks will be on top. If the ball joints have been replaced the zerk will be on the side or the bottom.

Jan 03, 2012 | 1997 Chevrolet Lumina

1 Answer

I have recently bought a 1984 Ford F150. I have greased the 4 zerks between the two front tires but am not sure if there are any more that I need to grease. Are there any more zerks that I should be...


Yes Upper and lower ball joints are probably the ones you greased, also ther are 4 more to greas on tyerod ends , 1 on pitman arm , and front & rear u joints on driveshaft. Good luck

Aug 17, 2011 | 1984 Ford F 150

1 Answer

Where are the grease zerks located on a 1996 Old Ciera S.L.?


they are located on the bottom center of the ball joints and the bottom center of the outer tie rod ends below the joint.at the rear of the suspension in the same location on the ball joints if this set up has rear ball joints.if you don`t see them it may have joints that are what they call permanetly sealed joints and don`t need grease.they should be checked for being worn out.

Jun 08, 2011 | 1996 Oldsmobile Cutlass Ciera

1 Answer

What all is involved in a regular vehicle Service?


Basically you change the oil and filter and possibly the air filter and fuel filter if they haven't been replaced recently. Most ball joints and tie-rod ends and such are sealed on newer vehicles but if they have grease zerks then they will need filled with grease. Also the u-joints may have grease zerks to lubricate.

Mar 05, 2011 | 1995 Jeep Grand Cherokee

1 Answer

How do you lube fron end of a 2000 LincolnTowncar Executive


You need a grease gun and grease. Locate all grease "zerks" on upper & lower ball joints, tie rod ends, etc.. Clean of dirt & grime build-up off zerks, push grease gun on and give a few pumps, then on to next zerk.

Mar 01, 2011 | 2000 Lincoln Town Car

2 Answers

How zerks to lube on 2008 lucerne?


There are no grease zerks.There is nothing to lube on your suspension.Most newer vehicle do not have grease zerks anymore.Hope this helps.Good luck.

Feb 09, 2011 | 2008 Buick Lucerne

1 Answer

Are there grease zerks on the 2002 corvette? if so how many and where?


now this is another new one ,?? please is a grease zerk a grease nipple in english ,i mean the bonnet is called a hood and the wiring a pigs tail and the engine guard a dogs kennel ,No i cannot say i have ever seen any on cars newer than 1995 or so if its a grease nipple your refering to

Jan 10, 2011 | 2002 Chevrolet Corvette

1 Answer

Squeak when turning, can also be made if vehicle is rocked


Your luckey to have grease zerks on your tierod ends most newer cars don't have any at all. If there any more they would be on the upper and lower ball joints, and maybe the a-frame bushings, but don't be surprised if you don't find any.

May 27, 2009 | 1998 Lincoln Mark VIII

Not finding what you are looking for?
2001 Ford Windstar Logo

249 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...