Question about 1989 Chevrolet C1500

1 Answer

89 chev 1500 halfton 4x4 was driving( radio off) hear pop or snap service engin light came on motor stoped , now turns over but wont start ?????

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 33 Answers

Check the timing chain.

Posted on Sep 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my 89 chev 4x4 s10 blazer turn over and back fire but won't start?


did you have any work done on the engine? it sounds as though the engine and/or valve timing may not be set correctly. Have the timing checked and reset if needs be. Good luck!

Apr 17, 2014 | 2001 Chevrolet Blazer

1 Answer

How do you remove the radio on a 1999 chev halfton?


First you need to remove the dash bezel. To do so you need to put the truck in low gear and tilt the column all the way down then grab a side or the top and pull on the bezel with moderate pressure. now that your down to the radio there are tabs on either side of the radio, push them down and pull the radio out. unplug the wiring harness and antenna from the back of the radio and your done.

Apr 25, 2011 | 1999 Chevrolet Silverado 1500

2 Answers

I have a 02 Chevy Z71 1500. I locked it in 4lo and now my (service 4wd) light is on and the lights on my panel for my auto, 2wd, 4hi and 4lo don't work. Plus it will not come out of 4lo. Any answer's?


Okay the motor for the 4x4 got stuck in 4LOW, Can you accsess the 4x4 motor switch,at see if that will retract the motor and default to 2 wheel drive because the switch itself went bad and wont disengage. see if that will help if not youll just have to by pass the switch and trigger to its normal position make sure its in neutral also

Apr 23, 2011 | 1999 Chevrolet K1500

1 Answer

Service light keeps coming 4x4 work fineand there are no leaks and i have alwayschanged oil as required in transfer case 1999 chev silverado 1500 5.3 engine


This is good that you have done this,but it does not mean there is no problem,have the auto zone read the codes stored in the computer.It can be just a o2 sensor,but have it checked to correct the problem.

Jul 06, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

2003 dodge pickup 5.7 hemi motor ---- driving along fine stoped at stop light it started to run rough , then stalled ,it started back up then stalled again . now it will roll over ok but will not...


your problem sounds fuel related chk your fuel pressure. or simply turn key off then to on position (engine off) and see if u can hear your fuel pump run (2-3 sec) then it will turn off.

Nov 07, 2009 | 2001 Dodge Ram 1500 Truck 2WD

2 Answers

Chevrolet Suburban 4 Wheel Drive Indicator Lights


Just serviced my own 4x4 Suburban, by buying a 2nd hand encoder motor and replaced the old one, which was trashed by the winter salt. The device is prone to failure since it's made of alluminium and water has an easy time of entering the unit and trashing it.

CAUTION: Abbreviated gratuitous information of how an encoder motor was serviced. If unqualified to deal with repair, seek professional service.
CAUTION: Read at one's own risk.

To replace it, you need to crawl under the vehicle and remove the front drive shaft;

Disconnect the electric harness to the encoder motor, followed by unbolting it.

Take replacement encoder motor and install. There may be an issue with aligning the cogged cam of the transfer case to the encoder motor. If so, the vehicle's 4 wheels will need to be raised off the ground. The engine started, transmission in Park, and using a Vice-Grip® wrench gently rotate cam clockwise approximately 1/16 to 1/8 of an inch, then while set in this position, stop engine. Now attempt to align and attach the encoder motor.

After successfully attaching new encoder motor, attach its wiring loom.
Test vehicle.


Mar 22, 2009 | 2003 Chevrolet Suburban 1500

1 Answer

89 chev truck 1500 4X4. Speedometer only works sometimes.


Sounds like a loose connection on insterment cluster. or a dead spot on printed circute, either way dash will have to come apart to fix.

Feb 12, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

ENGINE LIGHT ON ATFER HAVING IT SERVICE & THE 4 WHEEL DRIVE LIGHT


There are well over 100 problems in the electronics that turn the service engine soon light on, go to autozone or a kragen and they will run the trouble code test for free, then record that code and post it here. As far as the 4X4 goes that problem is most likely the electric motor that engages the 4X4 tranfer case, u will have to have that tested by either a 4X4 shop or the dealer, the dealer is the best option.

Jan 14, 2009 | 2004 Chevrolet Silverado 1500 Crew Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...