Question about 1993 Jeep Cherokee Country

1 Answer

Show installation procedures for front brakes on 1993 jeep cherokee ,country model. size of nut that holds front brake rotor in place

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

Don't need a diagram for this... Leave the center nut alone! To replace the pads and remove the rotors, remove the two bolts that are on the inboard side of the calipers. Can't remember the size but there are small, somewhere around 10mm to 1/2". Once you get them off, remove the pads, then re-install the inner pad and using a large "c" clamp, drive the piston back into the caliper.
Once the caliper has been removed, it should just about fall off.
If not, use lots of wd40 or other solvent around where it meets the hub and into the wheel studs where they pass through the rotor. Use a heavy mallet or even a hammer to loosen them up.
Rotors are inexpensive and generally cutting them unless they are not very old is not recommended, so don't bother saving them unless it's absolutely necessary.
Be careful threading the caliper bolts back in. They must be in straight as they are very narrow and easily cross threaded.Always make sure that the slides they pass through are not frozen ane are properly lubed. Install is the reverse of removal.

Posted on Sep 06, 2010

Testimonial: "thanks easy to understand and helpful."

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace Front Wheel Hub Bearing 2002 Jeep Grand Cherokee 2 wheel drive


Removal
  1. Raise and support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the brake caliper, caliper anchor, rotor and ABS wheel speed sensor.
  4. Remove the cotter pin, nut retainer and axle hub nut.
  5. Remove the hub/bearing mounting bolts from the back of the steering knuckle. Remove hub/bearing from the steering knuckle and off the axle shaft.
Installation
  1. Install the hub/bearing to the knuckle.
  2. Install the hub/bearing-to-knuckle bolts and tighten to specification.
  3. Install the hub washer and nut. Tighten the hub nut to specification. Install the nut retainer and a new cotter pin.
  4. Install the brake rotor, caliper anchor, caliper and ABS wheel speed sensor.
  5. Install the wheel and tire assembly.
  6. Remove the support and lower the vehicle.

Apr 22, 2012 | 2002 Jeep Grand Cherokee

1 Answer

When applying brakes at moderate speeds front brakes shudder


Rotors are warped and need to be turned down or replaced. Make sure when the wheels are put back on, that they are torqued down to the specifications for that jeep. I have a 92 cherokee and torque them to 100 ft. lbs. On disc brakes, the lug nuts on the wheels have to be torqued down or the rotors will keep warping, a lot of people don't know this.

Apr 11, 2010 | 1999 Jeep Cherokee

4 Answers

How do you remove the front brake rotor? Jeep Grand Cherokee 4X2


To remove the rotor you need to first remove the two bolts holding the caliper on. You need to make sure that you have something to put the caliper on or a piece of string to tie it up so that it's not hanging. After that, you need to remove the two bolts holding the caliper bracket on. You will have to get to this by looking behind the caliper (it's pretty easy to find). Once you have removed the caliper bracket, you will be able to just pull the caliper off. I have a 99 jeep and this is exactly how I did it just a couple of weeks ago. Let me know if once you have taken the caliper and bracket off if it doesn't just pull off. I assume the 01 and 99 will be the same. If it doesn't pull off, your jeep is a little different and you will have a hub nut in the middle of the rotor that you need to take off first. Again, I don't think that will be the case but if it is you can "rent" for free, the correct size socket from Auto Zone to take the hub nut off. Let me know if you have further questions. Thanks for rating my response and for using FixYa!

Jul 23, 2009 | 2001 Jeep Grand Cherokee

1 Answer

How do i remove stop relay switch at brake pedal grand cherokee 2000 model drawning if poss


disconnect the wire from the brake light switch, remove the 2 booster push rod nuts, slide out the push rod bolt.

Jun 20, 2009 | 1993 Jeep Cherokee Country

1 Answer

I have a 2000 wrangler did a front brake job on it (new rotors new pads) all back together fine then when i went to test drive jeep won't move acts like parking brake on. thanks


Try jacking up the front of your jeep and see if you can turn the front wheels by hand. If you can the do the same thing to the back. If you can't turn the front tires then you might have a brake caliper that needs to be replaced.

Jun 03, 2009 | 1993 Jeep Cherokee Country

1 Answer

I need to know the procedure for r and r on a front rotor if this is something that can be done at home with limited tools?


1999 Taurus/Sable Section 06-03: Brakes, Front Disc 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Disc Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Be careful to avoid damage or interference with caliper bleeder screw fitting and front disc brake rotor shield (2K004).
  1. ani_caut.gif CAUTION: Handle front disc brake rotor (1125) and disc brake caliper (2B120) assembly in such a way as to prevent deformation of front disc brake rotor , and nicking, scratching or contamination of brake linings/rotor surfaces.
    NOTE: To prevent damage, do not allow disc brake caliper to hang by the front brake hose (2078) .


    Remove caliper anchor plate bolts and discard. Position disc brake caliper out of the way. Prevent separation of caliper housing from anchor bracket because contamination of guide pin journals can occur.
  1. NOTE: If excessive force must be used during front disc brake rotor removal, the front disc brake rotor should be checked for runout prior to installation.


    If additional force is required to remove front disc brake rotor , apply Rust Penetrant and Inhibitor F2AZ-19A501-A or equivalent meeting Ford specification ESR-M99C56-A on front and rear rotor/hub mating surfaces. First, strike front disc brake rotor between lug bolts (1107) with a plastic hammer. If this does not work, attach 2-3 Jaw Puller 205-D027 (D80L-1013-A) or equivalent and remove front disc brake rotor . Remove front disc brake rotor from wheel hub (1104) assembly by pulling it off the lug bolts.
Installation
  1. If original front disc brake rotor is being installed, make sure rotor braking and mounting surfaces are clean.
  1. ani_caut.gif CAUTION: Failure to clean rust and foreign material from rotor and hub mounting faces when installing new or old front disc brake rotors will result in high rotor runout, which will speed up the development of brake roughness shudder vibration.
    Apply a small amount of Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A or equivalent meeting Ford specification ESE-M1C171-A to pilot diameter of front disc brake rotor.
  1. Install front disc brake rotor on wheel hub assembly.
  1. Install disc brake caliper and new caliper anchor bracket bolts on front disc brake rotor . Tighten caliper anchor bracket bolts to 88-118 Nm (65-87 lb-ft).
  1. ani_caut.gif CAUTION: Failure to tighten lug nuts (1012) in a star pattern may result in high rotor runout, which will speed up the development of brake roughness, shudder and vibration.
    Install wheel and tire assembly on vehicle. Tighten lug nuts to 115-142 Nm (85-104 lb-ft) using Rotunda Accutorq® Lug Nut Socket 164-R0303 or equivalent on a 1/2 inch air impact wrench, or use a torque wrench.
  1. Lower vehicle.
  1. Pump brake pedal prior to moving vehicle to position brake linings.
  1. Road test vehicle.









May 25, 2009 | 1999 Mercury Sable

1 Answer

CHanging out the front hub assembly on a 1992 Jeep Cherokee 4wd


Below is a link to the front rotor and all components on a 4WD Jeep Cherokee.

http://www.chiltonlibrary.com/content/images/8674/images/86749g36.pdf

4-Wheel Drive
  1. Loosen the lug nuts on the front wheels.
  2. Raise and support the vehicle safely.
  3. Remove the front wheels.
  4. Remove the calipers, but don't disconnect the brake lines. Suspend the calipers out of the way.
  5. Remove the rotor.
  6. Installation is the reverse of removal. Tighten wheel lug nuts to 75 ft. lbs. (101 Nm).
Best of luck!
Greg

May 20, 2009 | 1992 Jeep Cherokee Sport

3 Answers

When appling brakes on a 2000 Jeep Grand Cherokee, steeing wheel


New revised calipers. and have the new rotors machined right out of the box before installing

Dec 28, 2008 | 2000 Jeep Grand Cherokee

1 Answer

1993 Jeep Cherokee Front Rotor & Pad Replacement


This is a walk through for a 1993 2wd.

1. Jack up and remove tire
2. Remove 2 brake caliper mounting bolts
3. Remove caliper and hang out of way with wire
4. Remove rotor, if stuck hit on all sides with a rubber mallet until it breaks loose.
5. Install new rotor
6. Remove old pads from caliper
7. Using a c-clamp and a block of wood against caliper piston, compress piston until it is flush w/caliper
8. Install new pads in same location as old pads
9. Reinstall caliper, may have to nudge it into place with rubber mallet
10. Reinstall tire.

note: There are no bearings to grease. You must replace the entire hub assembly if yours are worn.

Jul 01, 2008 | 1993 Jeep Cherokee Country

Not finding what you are looking for?
1993 Jeep Cherokee Country Logo

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...