Question about Dodge Dynasty

1 Answer

The door what close at all and the lock what shut the door at all

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 33 Answers

Open the door and look at the lock check to see if the lock is shut, it will look like a ( C ) if it is in the correct position for a open door. If the lock has locked while the door is open it will be in a closed position. if this has happened you will need a screw driver , and when while the door is open insert the key, and insert the screw driver into the lock mechnism and pop it open as you unlock it with the key

Posted on Sep 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does rear passenger side door of 2000 Toyota Avalon occasionally not lock securely in freezing weather?


The actuator/latch is bad. Basically a spring in it is not tight enough to close it.

Dec 23, 2016 | Toyota Cars & Trucks

1 Answer

I have a 2002 Ford explorer and I can't figure out how to get the child safety lock off. The door doesn't shut now due to trying to disengage the lock. What can I do?


the child safety lock is normally a small lever at the edge of the door and has no effect on closing a door
it just prevents the door from being opened on the inside
what may have happened is that the door lock mechanism is in the 1/2 closed position and will not allow full lock (close) to occur
place a small screw drive under the latch or tongue of the lock and pull out as you press the door handle as if opening the door
that should then place the latch in the correct position for latching the door when closed properly

Sep 30, 2016 | Ford Cars & Trucks

4 Answers

I have a 1997 ford thunderbird lx and the other day when i went to close the door when i got out it,it wuldnt shut i slammed it a couple times n it still wouldnt shut i really need help because i cant...


Here's something that might help you. Look at the door theres a little hook that grabs the striker on car, hold the door handle "open" and move the hook to the open position try to close the door. That should solve your problem. Hope that helps you.

Aug 05, 2011 | Ford Thunderbird Cars & Trucks

1 Answer

1994 pontiac sunbird 3.1 L V6...door locking system has gone haywire. I got home, opened the door to the car, and when I tried to close the door, it would not shut. Can I unhook the battery to reset the...


Your door locks will not prevent your doors from closing, you should be able to lock the doors by hand and then close them with no problem. Take a look on the car where the door closes there will be a brass rod, this is your striker, it is what holds the door shut. This striker lines up with a latch in the door, the latch is on a spring and when the door is open it should be up, when the door closes the spring closes the latch around the striker. Check to make sure the latch is up, if it is not the door(when you try to close it) will typically bounce back toward you. If the latch is down you maybe able to take a flat head screw driver or prying device and twist the latch back up, this should allow your door to close. If you open the latch and it immediately closes it will need to be replaced. Hope this gets you on the right track.

Sep 24, 2010 | 1994 Pontiac Sunbird

1 Answer

Power locks stuck.... After a cold Christmas day,


should like water has frozen inside the door on the mech, its probely released by now , or water has cause a short in the door electrics

Dec 26, 2009 | 2007 Kia Sedona LX Minivan

1 Answer

My 2002 town & Country Rear sliding door wont close


You need to change the locking mechanism on the door,not the theft lock that you push down by the window,the lock that keeps thew door shut.I dont know why it wouldnt lock,it must be a factory defect,that worn out before its time..

Jul 29, 2009 | 2006 Pontiac Montana SV6

1 Answer

Door lock staying locked so door cant clamp on to the striker


Hello and welcome to FIXYA, it sounds like you have two problems, first the door ajar switches in your truck are sticking, and causing the ajar light to remain on, and second the door lock actuator is shorted and getting stuck in the lock position. To repair the switches, obtain a can of brake cleaner and spray the door latch of each door for about 3 to 5 seconds, then open and close the door 10 times to work the cleaner into the switches. To fix the lock problem, you must first pull up on the knob in the door panel to unlock it. Then remove the door panel, and replace the door lock actuator.

Feb 07, 2009 | 1999 Ford Explorer

1 Answer

Program my remote


Program your factory keyless entry functions
For 2001+ Tacomas equipped with a factory alarm or keyless entrymag-glass_10x10.gif, here are some programming options that allow you to adjust the way your locks work.
The first programming option allows you to set the entry unlock to: (A) unlock the driver door with one push, and the remaining doors with a second push OR (B) unlock all of the doors with a single push.
  • Open the driver's door. Remove the key from the ignition switch.
  • (Complete these steps within 40 seconds)
    1. Insert the key into and remove it from the ignition switch 2 times.
      (IN - OUT - IN - OUT)
    2. Close, then open the driver's door 2 times.
      (SHUT - OPEN - SHUT - OPEN)
    3. Insert the key into and remove it from the ignition switch 1 time.
      (IN - OUT)
    4. Close, then open the driver's door 2 times.
      (SHUT - OPEN - SHUT - OPEN)
    5. Insert the key into the ignition switch and leave it in.
    6. Close the driver's door.
    7. Turn the key from LOCK to ON 4 times, ending at LOCK
      (LOCK - ON - LOCK - ON - LOCK - ON - LOCK - ON - LOCK)
    8. Wait for the locks to stop, then remove the key from the ignition switch.
  • On the key fob, press and release both LOCK and UNLOCK buttons at the same time.
    1. [For all doors unlock] press and release the UNLOCK button.
    2. [For driver door unlock] press and release the LOCK button.
  • Open the driver's door. The programming is complete. If programming did not occur, start over.

Jan 13, 2009 | 2001 Toyota Tacoma

1 Answer

Power Locks are Buggy


are you sure all of the doors are shut completely?
try taping the door shutting sensors to the body. ha

Aug 12, 2008 | 1993 Toyota Camry V6

1 Answer

Door won't shut


I had the same problem on nearly the same day. The rear door would not close, and then in trying to fix it I flipped a latch closed. After trying all the child safety and power locking features, I just poked around with a small screwdriver until I could open the spring that held the latch closed. Once I got that open, the door worked normally.

Jul 11, 2008 | 2000 Volvo V70

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...