Question about Ford F-250

1 Answer

How do i change out a ignitionkey switch - F-250 Ford Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 195 Answers

Remove lower dash and or steering column covers. follow directly back from where the ignition cylinder is and the igntion switch is usually two bolts remove and replace in the opposite manner.

Posted on Sep 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to get trouble codes using ignitionkey on a2002ford f-150 van


You can't do that on your year. To new. If your looking to get engine or transmission codes. A code reader will do this. If your looking to get security codes. This takes a scanner.

Mar 03, 2016 | Cars & Trucks

1 Answer

How to change headlight/multifunctional switch


To change a light switch, you first need to remove the old switch. Then go to a hardware store and buy the new switch. Then hookup the electrical to the new switch. Make sue all the wires are grounded. Then screw the switch in place.


------------------------------------------------------------------------------------------
FGTech Galletto 2-Master EOBD2 V51 BDM-TriCore-OBD

Dec 18, 2012 | 2006 Kia Rio

1 Answer

Mazda Tribute v6 2002 5-8 seconds to start


sounds like a problem with the ignitionkey comuting with body control module verifying that it is the right key for the car. if you have another key and see if it does the same. reprogramming of keys may help. Prados have been known to have a similar prob.

Nov 17, 2012 | 2002 Mazda Tribute

1 Answer

How do I reset alarm on Toyota corola 2002


You'll need to set off the alarm for a few seconds.
then, look under the dash area for a button or, a toggle
switch. When you locate it, turn on the ignition
key, press and hold in the button (little
spring loaded micro button, red or black possibly)
until the alarm chirps 1 time. This should over ride
the system, and only the keyless entry part,
if installed, would still be operating.
The LED (light emiting diode) light in the dash
should also go on solid.

At this point. the alarm would have reset.
If this had a starter kill relay installed,
it would now be opened, and the engine would
turn over when tried. This is override/reset.

Oct 30, 2012 | 2004 Toyota Corolla

1 Answer

Have 1987 chevy pickup truck not getting fuel to the TBI unit. when you turn ignitionkey to "on" pump starts to pump fuel, and will start to run but shuts off after 2 to 3 second or so. Even...


Kent, That sounds like normal operation.....see this link (https://www.justanswer.com/chevy/0z9bu-fuel-pump-relay-located-1987-chevy-silverado.html) The ECM shuts the pump down if the engine doesn't begin running in two seconds. I would bleed out the fuel line up to the TBI...crack the line at the TBI then cycle the key a couple of times until you see gas coming out of the line at the TBI. That will ensure you have fuel at the TBI, then try to start the engine. See the link for additional info.

Feb 24, 2018 | Cars & Trucks

1 Answer

How to tun off timing light after changing the belt


with ignition turned on, using the trip switch , change the display to ODO, and then turn the ignition OFF
While pressing the trip switch,turn the ignition switch ON and hold for five seconds
Release the trip switch,then press the switch again within five seconds.The digital display should change to T- BELT MODE. Each press of the switch then should change the reset time by 10,000km increments. After setting the klms hold the trip switch ON for more than five seconds then release the switch. Check that the display has now changed back to ODO and that now the warning has gone off when the engine is started .

Dec 28, 2010 | 2006 Toyota Land Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...