Question about 2005 Lexus RX330

1 Answer

2005 RX330. P0018. new timing belt in vehicle(from dealer). timing is correct. changed both bank 1 and bank 2 camshaft sensors,changed crank sensor. Code erases but comes back. Engine idles smooth and drives fine. Any suggestions?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 61 Answers

Bad ecm

Posted on Jan 27, 2011

  • Jun Chen Jan 29, 2011

    or the bank 2 cam gear borke. just open the vavle cover to find out.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a csmshsft sensor on a 2008 cadillac srx


Before you replace a part you may or may not need . Why ? What code ? Does the vehicle run ? There has been a lot of confusion on these vehicles with variable valve timing , mixing up cam sensors with camshaft actuators
DTC P0008: Engine Position System Performance Bank 1

DTC P0009: Engine Position System Performance Bank 2
The presence of DTCs P0008 and P0009 along with P0016, P0017, P0018, and P0019 indicates a possible condition with the primary timing chain and the alignment between both intermediate sprockets and the crankshaft. Or, the crankshaft reluctor wheel has moved and is no longer referenced to top dead center (TDC).


?€¢
Observe the scan tool CMP Desired, Actual, and Angle Variance parameters before a DTC sets. This may help to isolate whether a condition is specific to one camshaft, one bank, or caused by a condition with the primary crankshaft timing.



DTC Descriptors
DTC P0010: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1

DTC P0013: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1

DTC P0020: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 2

DTC P0023: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 2

DTC P2088: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 1

DTC P2089: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 1

DTC P2090: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 1

DTC P2091: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 1

DTC P2092: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 2

DTC P2093: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 2

DTC P2094: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 2

DTC P2095: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 2
DTC P0341: Intake Camshaft Position (CMP) Sensor Performance Bank 1

DTC P0342: Intake Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 1

DTC P0343: Intake Camshaft Position (CMP) Sensor Circuit High Voltage Bank 1

DTC P0346: Intake Camshaft Position (CMP) Sensor Performance Bank 2

DTC P0347: Intake Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 2

DTC P0348: Intake Camshaft Position (CMP) Sensor Circuit High Voltage Bank 2

DTC P0366: Exhaust Camshaft Position (CMP) Sensor Performance Bank 1

DTC P0367: Exhaust Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 1

DTC P0368: Exhaust Camshaft Position (CMP) Sensor Circuit High Voltage Bank 1

DTC P0391: Exhaust Camshaft Position (CMP) Sensor Performance Bank 2

DTC P0392: Exhaust Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 2

DTC P0393: Exhaust Camshaft Position (CMP) Sensor Circuit High Voltage Bank 2
I'm sorry but when dealing with these problems your best bet is to take your vehicle to a qualified repair shop , I have never see a DIY'ER correct the problem with these , an in the end always end up taking it to the dealer .

Jul 24, 2016 | 2008 Cadillac Srx

1 Answer

I am getting code p0018. the pcm is not receiving signal from bank 2. could this be a relay? please help.


question you change the timing chines if you dont change te code p0018 is the camshaft correlation need to ck sensor or timing

Oct 10, 2014 | 2007 Hyundai Azera Limited Sedan

2 Answers

What can i do to fix p0420 & p0430 code.. 2005 ford expedition 5.4 ,,,, can you please tell me where is located p0010 code, A camshaft position actuator circuit/open bank 1... Same truck .. Thank you


p0420 and p0430 both indicate a clogged catalytic converter. the vehicle's control module has detected that the three-way catalytic converter is not working properly (is not as efficient as the factory is expecting). Replacing the oxygen (O2) sensors may sometimes fix the code, but in most cases the catalytic convert needs to be replaced to fix the problem. The p0010 indicates camshaft sensor. The camshaft sensor may be the main problem, as it will affect your timing and fuel/air ratio, which in turn can effect what your Oxygen sensors detect, throwing the p0420 and p0430.

Make sure your car is timed correctly by the timing chain/belt, reset light, then if it dont' solve the problem, change oxygen sensors, if those don't help, catalytic converter is clogged.

Dec 10, 2013 | Cars & Trucks

1 Answer

Toyota sequoia p0018


Here's a link to your P0018 code and causes,I had a 2004 Tundra,bought new,paid 31 grand,water pump started leaking,took to Toyota dealer,they put new timing belt and pump on and had no problem,only had 50,000 miles on it,but these vehicles are known for water pumps going bad.It cost me 1100.00 dollars.Sold truck,had 70,000 miles on it,had the 4.7 engine,had 2 oxygen sensors replaced by Toyota,was covered under warranty.The fuel injectors got clogged up,Toyota charged 99 bucks,it lost power and afterwards it would fly again.I would take to Toyota and let them check it out,here's the link I promised. https://www.obd-codes.com/p0018

Aug 02, 2017 | Cars & Trucks

1 Answer

P0014 p0366 cel codes


P0014 (causing the CEL) - "B" Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)



P0366 - Camshaft position Sensor B - Bank 1



All the means is you must take the vehicle to a dealer for timing belt change

Feb 03, 2013 | 2008 Audi A6 3.2

1 Answer

I have trouble code P0018.engine wont start


http://www.obd-codes.com/p0018



What does that mean?

This diagnostic trouble code (DTC) is generic and applies to all makes & models of vehicles. The crankshaft position sensor (CKP) and Camshaft position sensor (CMP) work in harmony to control the spark/fuel delivery and timing. They both consist of a reluctor, or tone, ring which passes over a magnetic sensor, which generates a voltage, indicating position.

The crankshaft sensor is part of the primary ignition system and functions as the "trigger". It detects the position of the crankshaft relays that information on to the PCM or the ignition module (depending on the vehicle) to control spark timing. The Camshaft position sensor detects the position of the camshafts and relays the information to the PCM. The PCM uses the CMP signal to identify the beginning of the injector sequence. What ties these two shafts and their sensors together is the timing belt or chain. The cam and crank should be precisely timed together.

If the PCM detects that the crank and cam signals are out of time by a specific number of degrees, this DTC will set. Bank 2 is the side of the engine that doesn't contains cylinder #1, the "A" sensor is most likely the intake camshaft side.

Note it is not uncommon on certain models to see this DTC in conjuction with P0008, P0009, P0016, P0017, and P0019. If you have a GM vehicle and have those multiple DTCs, check for service bulletins that may apply to your engine.
Symptoms

Symptoms of a P0018 will or may include:

  • Malfunction Indicator Lamp (MIL) illumination
  • The engine may run but with reduced performance
  • The engine may crank but not start
  • The engine may exhibit a rattle near the harmonic balancer indicating the tone ring is damaged
  • The engine may start and run, but poorly
Causes

Causes may include:

  • Timing chain stretched, or timing belt skipped a tooth due to wear
  • Misalignment of timing belt/chain
  • Tone ring on crankshaft slipped/broken
  • Tone ring on camshaft slipped/broken
  • Bad crank sensor
  • Bad cam sensor
  • Damaged wiring to crank/cam sensor
  • Timing belt/chain tensioner damaged
  • An improperly torqued crankshaft balancer
  • A mis-built or mis-timed engine
  • A loose or missing crankshaft balancer bolt
  • The CMP actuator solenoid stuck open
  • The CMP actuator stuck in a position other than 0 degrees

Feb 01, 2013 | Cars & Trucks

1 Answer

P0018


P0018 - Crankshaft Position Camshaft Position Correlation Bank 2 Sensor 'A'

P0018 Description Crankshaft Position Camshaft Position Correlation Bank 2 Sensor 'A' is the generic definition for the P0018; however your vehicle's manufacturer may have a different definition for the P0018 code.

Sep 25, 2012 | Smart fortwo Cars & Trucks

1 Answer

3.6vvt not starting


Hi there:

P0016 - Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)
The crankshaft position sensor (CKP) and Camshaft position sensor (CMP) work in harmony to control the spark/fuel delivery and timing. They both consist of a reluctor, or tone, ring which passes over a magnetic sensor, which generates a voltage, indicating position.



The crankshaft sensor is part of the primary ignition system and functions as the "trigger". It detects the position of the crankshaft relays that information on to the PCM or the ignition module (depending on the vehicle) to control spark timing. The Camshaft position sensor detects the position of the camshafts and relays the information to the PCM. The PCM uses the CMP signal to identify the beginning of the injector sequence. What ties these two shafts and their sensors together is the timing belt or chain. The cam and crank should be precisely timed together. If the PCM detects that the Crank and Cam signals are out of time by a specific number of degrees, this P0016 code will set.



Causes may include:
Timing chain stretched, or timing belt skipped a tooth due to wear
Misalignment of timing belt/chain
Tone ring on crankshaft slipped/broken
Tone ring on camshaft slipped/broken
Bad crank sensor
Bad cam sensor
Damaged wiring to crank/cam sensor
Timing belt/chain tensioner damaged

Possible Solutions: First, visually inspect the cam and crank sensors and their harnesses for damage. If you notice broken/frayed wires, repair and recheck.
If you have access to a scope, check the cam and crank patterns. If a pattern is missing, suspect a bad sensor or a slipping tone ring. Remove the cam gear and the crankshaft harmonic balancer and inspect the tone rings for proper alignment and make sure they're not loose or damaged or that they haven't sheared the key that aligns them. If they are properly installed, replace the sensor.
If the signal appears normal, then check the timing chain/belt for proper alignment. If it's misaligned, check for a damaged tensioner that may have allowed the chain/belt to slip a tooth or several teeth. Also check that the belt/chain isn't stretched. Repair and recheck.

Other crank sensor codes include P0017, P0018, P0019, P0335, P0336, P0337, P0338, P0339, P0385, P0386, P0387, P0388, and P0389.


Additionally, in THIS LINK can find description and test about this fault.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jul 31, 2012 | Cars & Trucks

1 Answer

Code p0019 p0018 p0008


P0019: Cam/Crankshaft Pos. Correlation Sensor B - Bank 2
P0018: Cam/Crankshaft Pos. Correlation Sensor A - Bank 2
P0008: Engine Position System Performance (Bank 1)

P0019 & P0018
- Dirty Oil
- Engine mechanical problems
- Timing belt jumped teeth

P0008
- Engine mechanical problems
- Incorrect timing chain
- Stretched timing chain
- Failed camshaft actuator or actuator solenoid

The Engine Control Module (ECM) monitors the position of both camshafts and the crankshaft. The ECM performs a test for misalignment between both camshafts on one bank of the engine and the crankshaft. During the test the ECM learns the position of the camshafts and the crankshaft. While the engine is idling, the ECM compares the position of both the camshafts and the crankshaft with the learned value. The ECM will set the P0008 code if both learned values for one bank of the engine are exceeding a calibrated threshold in the same direction.

Feb 07, 2012 | 2005 Suzuki XL-7

1 Answer

3.6 in a 2006 pontiac g6 is throwing code p0017 is this crank sensors or what is the most common fix


P0017 - Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B)

The crankshaft position sensor (CKP) and Camshaft position sensor (CMP) work in harmony to control the spark/fuel delivery and timing. They both consist of a reluctor, or tone, ring which passes over a magnetic sensor, which generates a voltage, indicating position.

The crankshaft sensor is part of the primary ignition system and functions as the "trigger". It detects the position of the crankshaft relays that information on to the PCM or the ignition module (depending on the vehicle) to control spark timing. The Camshaft position sensor detects the position of the camshafts and relays the information to the PCM. The PCM uses the CMP signal to identify the beginning of the injector sequence. What ties these two shafts and their sensors together is the timing belt or chain. The cam and crank should be precisely timed together. If the PCM detects that the Crank and Cam signals are out of time by a specific number of degrees, this P0017 code will set.

Symptoms of a P0017 will or may include:
* Malfunction Indicator Lamp (MIL) illumination
* The engine may run but with reduced performance
* The engine may crank but not start
* The engine may exhibit a rattle near the harmonic balancer indicating the tone ring is damaged
* The engine may start and run, but poorly

Causes may include:
* Timing chain stretched, or timing belt skipped a tooth due to wear
* Misalignment of timing belt/chain
* Tone ring on crankshaft slipped/broken
* Tone ring on camshaft slipped/broken
* Bad crank sensor
* Bad cam sensor
* Damaged wiring to crank/cam sensor
* Timing belt/chain tensioner damaged

Possible Solutions:
1. First, visually inspect the cam and crank sensors and their harnesses for damage. If you notice broken/frayed wires, repair and recheck.
2. If you have access to a scope, check the cam and crank patterns. If a pattern is missing, suspect a bad sensor or a slipping tone ring. Remove the cam gear and the crankshaft harmonic balancer and inspect the tone rings for proper alignment and make sure they're not loose or damaged or that they haven't sheared the key that aligns them. If they are properly installed, replace the sensor.
3. If the signal appears normal, then check the timing chain/belt for proper alignment. If it's misaligned, check for a damaged tensioner that may have allowed the chain/belt to slip a tooth or several teeth. Also check that the belt/chain isn't stretched. Repair and recheck.

Other crank sensor codes include P0016, P0018, P0019, P0335, P0336, P0337, P0338, P0339, P0385, P0386, P0387, P0388, and P0389.


Hope this helps (remember to rate and comment this answer).

Nov 23, 2010 | 2006 Pontiac G6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

771 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

917 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...