Question about 2001 Mitsubishi Eclipse

1 Answer

I need to replace the fog light on the drivers side. Can I do that myself without taking it to a licensed mechanic?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

Yes. You may need to get to it underneath, but should be a easy job.

Posted on Sep 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear fog light shows up needs checking, which light bulb is the rear fog bulb?


Audio and WV have a rear fog lights that are usually behind a clear lens to either side of the license plate. They are activated by pulling on the headlight switch two notches. Pulling one notch turns on the front fog lights.

Jan 27, 2016 | Cars & Trucks

1 Answer

Changing fog light on a 2004 Kia Magentis EX V6


I believe you just need to reach up and under the bumper to disconnect the bulb and the harness

Aug 18, 2009 | 2005 Kia Sportage

1 Answer

Changing fog lights


you can take loose the black plastic shield that runs from inner fender to bottom of bumper. once loose you gain access to back of fog light where mounting bolts are located if its just the bulb your replacing you can also do that without removing it

Jun 28, 2009 | 1998 Dodge Neon

2 Answers

How to replace fog light bulbs


hi..You will have to access the fog light bulb from below the vehicle.
Remove the plastic clips from the wheel well cover extension that is
below the fog light.once the clips are out and the plastic cover is pull
down,you should be able to see the back of the fog light.you can try
to replace the fog light bulb by removing the two 10mm bolts and slide
the fog light assemble out through the front of the bumper.Turn the cover
of the rear of the fog light and replace light.
try this out..
thank u..
kindly rate my response..

Jun 14, 2009 | 2004 Toyota Celica

1 Answer

2001PT Cruiser door locks


The fuse is No.3 "DR locks" (near steering wheel)
If you take the fuse out the doors will not open itselves.

The root cause of the problem will be a microswitch inside the drivers door?

Check this:
http://www.ptdoityourself.net/tl/tl_index2.html#8n

======FOG LIGHTS ============

1.At first take out the foglight's fuse before you battery is dead. (Fog lights stays "ON" even you leave the car).

2.You must replace the Multifunction control switch =(

Here is the photo of problem:
http://www.ptcruiser.fi/ptgalleria/albums/userpics/10010/normal_sumuvalokytkin.jpg

Fog lights are connected to pin 13,14.
Fog light switch is "B". Because the current is many Amps, contact surfaces are heating up.
After that the contact opening "C" is melting (made of plastic) so the fog light stays "ON".

May 20, 2009 | 2002 Chrysler PT Cruiser

1 Answer

How do you replace the fog lamp on a 1997 dodge neon? As best as I can tell, you have to take off the front bumper which I hope is not the case.


To replace the fog light of the passenger side you need to remove the fog light bolt and pull out the fog light assembly, then you can remove the bulb and put a new one in.

To replace the fog light on the driver side you will need to remove the front bumper cover so you can remove the vacuum box that is in the the way of the fog light bolt.

To do so you need to remove the Torx (star) screws located in the front wheel wells as well as the bolts holding the plastic by the radiator. "CAUTION: DO NOT UNBOLT THE RADIATOR."

If any of the screws are rusted into place put some penetrating oil them to help loosen them up.

PLEASE DON'T FORGET TO RATE!!!

Mar 16, 2009 | 2002 Chrysler Voyager

1 Answer

2002 Grand Am Guage lights, fog, rear license, tail lights out


sounds like there is a bad short and they are hard to find.

Mar 04, 2009 | 2002 Pontiac Grand Am

1 Answer

Fog light replacement driver side


new light and yes the bumper has too come off to get to the bolts at the bottom of the lights..

Dec 11, 2008 | 1997 Volkswagen Golf

1 Answer

How to replace bulb for fog on the front .


You can access it from behind.You have to remove splash shield and go from the underside.

Nov 12, 2008 | 1999 Lexus RX 300

1 Answer

Replace fog light in 2001 cadillac Deville


is it on a DTS or is it the marker side light.

Jun 23, 2008 | 2001 Cadillac DeVille

Not finding what you are looking for?
2001 Mitsubishi Eclipse Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...