Question about Chevrolet Blazer

1 Answer

Where do the fuel lines hook up from firewall to motor on vortek 1999 chev blazer

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

At the back of the intake manifold, drivers side.

Posted on Sep 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuse for the blower motor an a 1999 Chev Blazer?


Should be a 30amp fuse in the box in the engine compartment.

Feb 21, 2015 | 1999 Chevrolet Blazer

1 Answer

1999 chev blazer won't start new fuel pump


So, do you hear the pump buzz on, when key is on? If that's good, then check your ignition circuit: check for spark at a plug. Use insulated pliers, hold end of plug wire 1/4 inch form engine bolt or ground source. When cranked, you should see a bright blue spark. Yes? Try another plug wire, too. No? Try another plug wire. If you have NO spark, could be your coil, coil pack, crank position sensor, ignition module. I would recommend using a diagnostic flow-chart to go through the ignition circuit. That way, you are not replacing unecessary parts_Expensive! Of course, if you have spark at plugs, your ignition circuit is good! Then you have to look further, like your injector circuit. Good luck.

Oct 30, 2011 | 1999 Chevrolet Blazer

1 Answer

Bought a new motor having trouble getting it on the timing. Its a 1999 chev blazer 4.3


would try going to www.autozone.com Log in. Then, vehicle repair guides. It will give you pictures and step by step guide. have a good day!! 7e85a108-8532-fcd6-059979af8418ea26.png

Nov 27, 2010 | 1999 Chevrolet Blazer

1 Answer

94' blazer will not strart just died one day while driving it .i replaced fuel pump,fuel filter,fuel ragulater, if you spray starting fluid in it it will start but then die whin the starting fluid burns...


check to make sure they sold you the right fuel pump. they are two pumps for a 4.3 ones a vortek and one is a throtlle body. the eighth digit of the vin will tell you one is a vin w and one is a vin z. the throtlle body only puts out about 11psi of pressure and the vortek puts out about 60psi of pressure.if you put the throttle body pump in a vortek engine there is not enough fuel pressure to run it.

Oct 20, 2010 | 1994 Chevrolet S-10 Blazer

2 Answers

Antifreeze leak on 97 chev blazer


Could be a heater hose or head gasket

Sep 08, 2009 | 1999 GMC Jimmy

1 Answer

1994 S-10 Chev will not start.


Undo the air intake hose and see if you can get it to start by spraying carb cleaner into the throttle body. Also you said the fuel pump is fine. You have 55 psi?

Jun 02, 2009 | 1994 Chevrolet S-10

2 Answers

4 wheel drive on 1999 chevy blazer


99 chev blazer should have an electric motor not a vac switch...Is your controll on the dash a switch you turn.. or on the floor you shift ??

Jan 07, 2009 | 1999 Chevrolet Blazer

1 Answer

I want to remove heater blower motor on a 1999 Chev Blazer Thanks


inside engine compartment on passanger side on firewall. If I recall correctly, you have to remove cooling resivor, and computer. You don't have to unplug the computer you might have to pinch off the hose on the resivor. Once those two are removed, you unplug blower motor and undo I think 5 or 6 small bolts and do the reverse for installiton.

Dec 24, 2008 | Chevrolet Blazer Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...