Question about Peugeot 405

1 Answer

I hav jst rebuilt my cylinder head on my 3071.6 hdi with new cambelt and new camshaft hain and tensioners and it starts ok but sounds like a tank u get a roar of it when u rev it sounds to me like the inlet manifold is blowing thats the noise im geting but its not that any1 any idears

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Peugeot Master
  • 7,772 Answers

Exhaust manifold not torqued or flange at end of manifold leaking

Posted on Sep 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jst put new cambelt on 54 plate corsa 1.8 16v sri now not starting getting code 0340 camshaft sensor can anyone help


Recheck the timing as possible it's 1 tooth out and this will give false reading from sensor if all is ok timing wise sensor at fault damaged, stressed wiring to sensor

Aug 07, 2013 | Vauxhall Cars & Trucks

1 Answer

How do i reset the timing on 2001 2.7l concorde if the chain was replaced and the timing is off


Did you take pictures while removing the originals? It's always a good habit. Below are the instructions you need to follow. Your own pics are very helpful when doing a big job like this.
  1. Disconnect negative battery (1) cable.
  2. Drain cooling system.
  3. Remove upper intake manifold.
  4. Remove cylinder head covers, crankshaft vibration damper, and timing chain cover.
CAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage.
117014297

  1. Align crankshaft sprocket timing mark to mark on oil pump housing (2). The mark on oil pump housing is 600 ATDC of #1 cylinder.
CAUTION: When the timing chain is removed and the cylinder heads are still installed, DO NOT rotate the camshafts or crankshaft without first locating the proper crankshaft position. Failure to do so will result in valve and/or piston damage.
117016938

  1. Remove primary timing chain tensioner retainer cap (2) and tensioner (1) from right cylinder head.
117016939

  1. Disconnect and remove camshaft position sensor (4) from left cylinder head.
  2. Remove timing chain guide access plugs (3) from cylinder heads.
NOTE: When camshaft sprocket bolts are removed, the camshafts will rotate in a clockwise direction.
  1. Starting with the right camshaft sprocket, remove the sprocket attaching bolts. Remove camshaft damper (1) (if equipped) and sprocket.
  2. Remove left side camshaft sprocket attaching bolts and remove sprocket.
  3. Remove lower chain guide (7) and tensioner arm (8).
  4. Remove the primary timing chain (5).
  5. Remove crankshaft sprocket (6).
INSTALLATION
117016940

  1. Inspect all sprockets (4,9,11) and chain guides (2,5,10). Replace if worn.
  2. For crankshaft sprocket installation procedures Refer to CRANKSHAFT SPROCKET.
  3. If removed, install right and left side short chain guides (11). Tighten attaching bolts to 28 Nm (250 inch lbs.) .
  4. Align crankshaft sprocket timing mark to the mark on oil pump housing (3).
NOTE: Lubricate timing chain and guides with engine oil before installation.
  1. Place left side primary chain sprocket onto the chain so that the timing mark is located in-between the two (plated) timing links (1).
117016941

  1. Lower the primary chain with left side sprocket through the left cylinder head opening.
NOTE: The camshaft sprockets can be allowed to float on the camshaft hub during installation.
  1. Loosely position left side camshaft sprocket over camshaft hub.
  2. Align timing (plated) link to the crankshaft sprocket timing mark (3).
  3. Position primary chain onto water pump drive sprocket (10).
  4. Align right camshaft sprocket timing mark to the timing (plated) link on the timing chain (8) and loosely position over camshaft hub.
  5. Verify that all chain timing (plated) links are properly aligned to the timing marks on all sprockets.
  6. Install left side lower chain guide (2) and tensioner arm (5). Tighten attaching bolts to 28 Nm (250 inch lbs.) .
NOTE: Inspect O-ring on chain guide access plugs before installing. Replace O-ring as necessary.
  1. Install chain guide access plugs to cylinder heads. Tighten plugs to 20 Nm (15 ft. lbs.) .
NOTE: To reset the primary timing chain tensioner, engine oil will first need to be purged from the tensioner.
117016942

  1. Purge oil from timing chain tensioner using the following procedure:
    1. Place the check ball (2) end of tensioner into the shallow end of Special Tool 8186 (3).
    2. Using hand pressure, slowly depress tensioner until oil is purged from tensioner.
117016943

  1. Reset timing chain tensioner using the following procedure:
    1. Position cylinder plunger (4) into the deeper end of Special Tool 8186 (3).
    2. Apply a downward force until tensioner is reset.
NOTE: If oil was not first purged from the tensioner, use slight finger pressure to assist the center arm pin of Special Tool 8186 to unseat the tensioner's check ball.

CAUTION: Ensure the tensioner is properly reset. The tensioner body (4) must bottom against the top edge of Special Tool 8186 (3). Failure to properly perform the resetting procedure may cause tensioner jamming.

NOTE: Inspect the tensioner O-ring (2) for nicks or cuts and make sure the snap ring (1) is correctly installed, replace as necessary.
117016944

  1. Install the reset chain tensioner (1) into the right cylinder head.
  2. Position tensioner retaining plate (2) and tighten bolts (1) to 12 Nm (105 inch lbs.) .
117016945

  1. Starting at the right cylinder bank, first position the camshaft damper (1) (if equipped) on camshaft hub, then insert a 3/8 square drive extension with a breaker bar into intake camshaft drive hub. Rotate camshaft until the camshaft hub aligns to the camshaft sprocket and damper attaching holes. Install the sprocket attaching bolts and tighten to 28 Nm (250 inch lbs.) .
  2. Turn the left side camshaft by inserting a 3/8 square drive extension with a breaker bar into intake camshaft drive hub and rotate camshaft until the sprocket attaching bolts can be installed. Tighten sprocket bolts to 28 Nm (250 inch lbs.).
  3. Rotate engine slightly clockwise to remove timing chain slack, if necessary.
117016946

  1. Activate the timing chain tensioner by using a flat bladed pry tool to gently pry tensioner arm towards the tensioner slightly. Then release the tensioner arm. Verify the tensioner is activated (extends).
117016947

  1. Install camshaft position sensor (2) and connect electrical connector.
  2. Install the timing chain cover, crankshaft vibration damper, and cylinder head covers.
  3. Install upper intake manifold.
NOTE: After installation of a reset tensioner, engine noise will occur after initial start-up. This noise will normally disappear within 5-10 seconds.
  1. Fill cooling system.

Mar 27, 2013 | 2001 Chrysler Concorde

1 Answer

Hi, noticed a post of yours rear cambelt replacement on an a4 1.9 tdi ajm year 2000. Would be very grateful for any instructions. The car is stripped down ready for cambelt removing. Stuck on lining up...


Hi, I have pasted instructions below from autozone.com. The instructions call for the use of special tools. You can improvise with alternate tools, but please make sure your timing is right before closing the cover. Please let me know if you have questions, and thanks for using FixYa.

1.9L Diesel Engine
Some special tools are required to perform this procedure properly. A flat bar, VW tool 2065A is used to secure the camshaft in position. A pin, VW tool 2064 is used to fix the pump position while the timing belt is removed. The camshaft and pump work against spring pressure and will move out of position when the timing belt is removed. It is not difficult to find substitutes but do not remove the timing belt without these tools.

WARNING Do not turn the engine or camshaft with the timing belt removed. The pistons will contact the valves and cause internal engine damage.
  1. Disconnect the negative battery cable and remove the accessory drive belts, crankshaft pulley and the timing belt cover(s). Remove the camshaft cover and rubber plug at the back end of the camshaft.
  2. Temporarily reinstall the crankshaft pulley bolt and turn the crankshaft to Top Dead Center (TDC) of No. 1 piston. The mark on the camshaft sprocket should be aligned with the mark on the inner timing belt cover or the edge of the cylinder head.
  3. With the engine at TDC, insert the bar into the slot at the back of the camshaft. The bar rests on the cylinder head to will hold the camshaft in position.
  4. Insert the pin into the injection pump drive sprocket to hold the pump in position.
  5. Loosen the locknut on the tensioner pulley and turn the tensioner counterclockwise to relieve the tension on the timing belt. Slide the timing belt from the sprockets.

    jturcotte_1820.gif

    Fig. Use the VW tool to lock the camshaft at TDC for timing belt replacement-Volkswagen 1.9L Diesel engines


    jturcotte_1821.gif

    Fig. Locking the injection pump with the VW tool as shown-Volkswagen 1.9L Diesel engines


To install:
  1. Install the new timing belt and adjust the tension so the belt can be twisted 45 degrees at the halfway point between the camshaft and pump sprockets. Tighten the tensioner nut to 33 ft. lbs. (45 Nm).
  2. Remove the holding tools.
  3. Turn the engine 2 full revolutions to return to TDC for the No. 1 cylinder. Recheck belt tension and timing mark alignment, readjust as required.
  4. Install the belt cover and accessory drive belts.
    NOTE If the belt is too tight, there will be a growling noise that rises and falls with engine speed.

Jun 11, 2011 | Audi A4 Cars & Trucks

1 Answer

Gearbox chatter on tick over do they suffer from dualmass problems also is there a quick way to change the cambelt


Dual Mass Flywheel, and will also need new clutch Remove the engine coverUsing a [16 mm], rotate the tensioner arm clockwise (about 14° )and remove the belt from the pulley.
Remove the power steering pump pulley, idler pulley, tensioner pulley and crankshaft pulley.
Remove the upper and lower timing belt covers.

Remove the auto tensioner.
NOTE
Rotate the crankshaft clockwise and align the timing mark to set the No.1 cylinder's piston to TDC (compression stroke).
At this time, the timing marks of the camshaft sprocket and cylinder head cover should coincide with each other.




Unbolt the tensioner to remove the timing belt.
NOTE
If you plan to use the timing belt again, mark the rotation direction on the belt so you reinstall it correctly.

SERVICE MANUAL
Applies to: Santa Fe 2004
GROUP
Engine Mechanical System Timing System



INSTALLATION
Install the idler pulley to water pump boss.
NOTE
Insert and install the idler pulley to the roll pin that is pressed in the water pump boss.


Install the tensioner arm and plain washer to the cylinder block.
Install the tensioner pulley to the tensioner arm.
Install the camshaft sprockets and align the timing marks.

NOTE
When installing the camshaft sprockets, fasten them tightly while holding the hexagonal part of the camshaft.
Before installing the timing belt, if the timing marks of the cam sprocket and the cylinder head cover do not coincide, do not rotate the cam sprocket more than 3 teeth in either direction.
Rotating the sprocket more than 3 teeth may allow the valve and piston to touch each other.
If the cam sprocket is rotated more than 3 teeth unavoidably, rotate the crankshaft counter - clock wise a bit before rotating the cam sprocket.
Install the auto tensioner to the front case.
NOTE
At this time auto tensioner's set pin should be compressed and secured with set pin.




Align the timing marks of each sprocket and install the timing belt in the following order. Crankshaft sprocket--> Idler pulley--> camshaft sprocket (LH side)--> Water pump pulley--> camshaft sprocket (RH side)--> Tensioner pulley.
NOTE
In this step, No. 1 cylinder is in the TDC (Compression stroke).
Be very careful if you use your fingers.



Pull out the set pin of the auto tensioner.



Install the upper and lower timing belt covers.
Install the power steering pump pulley, idler pulley, tensioner pulley and crankshaft pulley.
Using the wrench [16mm], rotate the tensioner arm clockwise (about 14°) and install the belt to the pulley.
Install the engine cover.
How to adjust the tension of the timing belt
Rotate the crankshaft 2 turns clockwise and measure the projected length of the auto tensioner at TDC (# 1 Compression stroke) after 5 minutes.
The projected length should be 6-8 mm.
Verify that the timing marks of each sprocket are in their specified position.
NOTE
If the timing marks are not in their specified position, repeat from 6 above.

Dec 28, 2010 | 2004 Hyundai Santa Fe

1 Answer

Need cylinder head torque specifications 2004 hyundai elantra


Install the cylinder head bolts. Starting at top center, tighten all cylinder head bolts in sequence as shown in illustration, using the Cylinder Head Bolt Wrench (09221 - 32001) or equivalent. Repeat the procedure, re-tightening all cylinder head bolt to the specified torque. (torque spec is Cold Engine 105-115 Nm (76-83 ft lb) )
. Install the timing belt tensioner pulley.
. Install the timing belt on the camshaft sprocket, making sure that the tension side is tightened by turning the camshaft sprocket in reverse, all timing marks are in alignment.
. Adjust the timing according to "Timing Belt"
. Install the rocker cover and tighten the bolts to the specified torque. Tightening torque: Rocker cover belt:

2.5-3.5 Nm (25-35 kg.cm, 2-3 ft. lbs.)

. Install the timing belt cover.
Install the new intake manifold gasket and the intake manifold. Tighten the nuts and bolts to the specified torque.
Install the new exhaust manifold gasket and the exhaust manifold. Tighten the exhaust manifold attaching nuts to the specified torque.
. Install the surge tank and tighten the nuts bolts to the specified torque.
. Install the power steering oil pump and bracket.
. Install the ignition coil.
. Install the air intake hose.
Connect the vacuum hose, fuel hose and water hose.
. Install breather hose.

Dec 22, 2010 | 2004 Hyundai Elantra

1 Answer

I just had my water pump changed and when everything was all finished I was told to start my car. Well it started right up but it sounded like the chain was dragging on metal. I opened the front plate and...


here is the procedure for the tensioner:
    1. Purge oil from the timing chain tensioner using the following procedure:
    1. Remove the tensioner from the tensioner housing.
    2. Place the check ball end of the tensioner into the shallow end of the Tensioner Resetting Special tool 8186.
    3. Using hand pressure, slowly depress the tensioner until oil is purged from the cylinder.
    4. Reinstall the tensioner into the tensioner housing.

    1. Reset the timing chain tensioner using the following procedure:
    1. Position the cylinder plunger into the deeper side of the Tensioner Resetting special tool 8186.
    2. Apply a downward force until the tensioner is reset.
      WARNING Ensure that the tensioner is properly reset. The tensioner body must be bottomed against the top edge of the Tensioner Resetting Special tool 8186. Failure to properly perform the resetting procedure may cause tensioner jamming.
    1. Install the chain tensioner into the right cylinder head.
    2. At the right cylinder head, insert a 3 / 8 in. square drive extension with a breaker bar into the intake camshaft drive hub. Rotate the camshaft until the camshaft hub aligns with the camshaft sprocket and damper attaching holes. Install the sprocket attaching bolts and torque to 21 ft. lbs. (28 Nm).
    3. Turn the left camshaft by inserting a 3 / 8 in. square drive extension with a breaker bar into the intake camshaft drive hub. Rotate the camshaft until the camshaft hub aligns with the camshaft sprocket and damper attaching holes. Install the sprocket attaching bolts and torque to 21 ft. lbs. (28 Nm).
    4. If necessary, rotate the engine slightly clockwise to remove any slack in the timing chain.
    5. To arm the timing chain tensioner: Use a flat-bladed prytool to gently pry the tensioner arm towards the tensioner slightly. Then, release the tensioner arm. Verify the tensioner extends.

    Oct 04, 2010 | 2002 Dodge Intrepid

    1 Answer

    Got audi a4 1996 diesel need to change cambelt but


    A diesel uses a different procedure. You'll need a tool to hold the camshaft pulley parallel to the top of the cylinder head. The timing mark to set TDC for piston #1 is located on top of bell housing. The pointer must be aligned on the diamond cut on the flywheel. A VW/Audi setting bar tool #2065A is needed to lock the camshaft in position. Lock the injection pumpin position using the special lock pin (VW/Audi special tool no. 2064). Caution: If the drive belt is broken or has jumped time, do not attempt to lock the sprocket at this time!!! You will also need VW/Audi special tool no. VW210 to measure belt tension between camshaft sproket and injection pump sprocket. So good luck.

    May 01, 2010 | 1996 Audi A4

    1 Answer

    I need the head bolt torque specification for a 2005 aveo


    install:
    1. The cylinder head should be cleaned and inspected prior to installation.
    2. Lightly oil all bolt and stud bolt threads before installation.
    3. Clean all gasket mating surfaces thoroughly.
    4. Install a new head gasket on the cylinder block. WARNING Always use new cylinder head bolts when installing the cylinder head or damage to the engine may occur.
    5. Install the cylinder head on the cylinder block.
    6. Tighten the cylinder head bolts in reverse of the removal sequence. Tighten the 2004 cylinder head bolts to 18 ft. lbs. (25 Nm). Tighten an additional 70°, plus 70°, plus another 50°. Tighten 2005 bolts to 18 ft. lbs. (25 Nm). Tighten an additional 60°, plus 60°, plus another 10°.
    7. Install the right engine mount. Tighten the engine mount attaching bolts to 22 ft. lbs. (30 Nm).
    8. Install or connect the following:
      • Intake manifold
      • Intake manifold support bracket. Tighten the bolts to 18 ft. lbs. (25 Nm).
      • Throttle cable
      • Surge tank coolant hose
      • Heater hose to cylinder head
      • Fuel feed line at the fuel rail
      • All vacuum hoses
      • Exhaust manifold
      • Rear timing belt cover
      • Timing belt tensioner. Tighten the bolts to 18 ft. lbs. (25 Nm).
      • Idler pulley. Tighten the bolts to 18 ft. lbs. (25 Nm).
      • Intake and exhaust camshaft gears. Tighten the bolts to 49 ft. lbs. (68 Nm).
    9. Apply a small amount of gasket sealant to the corners of the front camshaft caps and the top of the rear camshaft cover-to-cylinder head seal.
    10. Install the valve cover using a new gasket
    11. Align the timing marks on the camshaft gears.
    12. Align the mark on the crankshaft gear with the notch at the bottom of the rear timing belt cover.
    13. Install the timing belt and rotate the water pump clockwise to apply tension to the timing belt.
    14. Tighten the water pump bolts to 89 inch lbs. (10 Nm).
    15. Adjust the timing belt tension.
    16. Install or connect the following:
      • Spark plug wires
      • Upper and lower timing belt coversCrankshaft pulley. Tighten the bolt to 70 ft. lbs. (95 Nm), plus an additional 30°, then another 15°.
      • Accessory drive belt
      • Air cleaner housing
      • Radiator hoses
      • Front splash shield
      • Right front wheel
      • Coolant temperature sensor
      • Fuel feed line from fuel rail
      • IAT sensor
      • Intake manifold pressure sensor
      • DIS coil connector
      • Fuel injector connectors
      • ECM ground terminal
      • Negative battery cable
    17. Fill the engine with oil and coolant.
    18. Start the engine and check for leak0900c1528009e8b5.jpg

    Apr 02, 2010 | 2005 Chevrolet Aveo

    1 Answer

    Nned to know how to set the cam and engine timing


    Start with crankshaft pulley. At the rear of the pulley is a notch. Align it with the mark on the oil pump.(No 2 piston is at TDC) There is also a groove on the pulley that needs to be aligned with the white dots on the cambelt. The lettering on the belt must be readable as viewed from the front of the vehicle.
    (When seated in the vehicle the RH bank of the engine is on the RH side of the vehicle.Keep this in mind)
    At the front of the camshaft pulley is a groove. Rotate the RH bank camshaft pulley to align this groove with the mark on the cylinder head cover. On the cambelt is a white line. This must also align with these marks. Do the same on the LH bank. To be sure the cams are now correctly aligned remove the cylinder head cover. On the camshaft drive gears the letters RI(Right intake) and RE(Right exhaust) will be at the top and readable for the RH bank. (For the LH bank it will be LI and LE) Reinstall the tensioner and rotate the crankshaft with a wrench to make sure there is no unintentional mechanical contact.

    Dec 10, 2009 | 2002 Isuzu Rodeo

    2 Answers

    Location of a cam sensor


    Hi
    you didn`t say which engine,but as a rule they are mounted behind the cambelt cover very near the camshaft sprocket not easy to change,if not there it will be mounted in the cylinder head relative to one camshaft.

    Jul 17, 2009 | 2002 Mitsubishi Galant

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    77 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Peugeot Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Wahs Team

    Level 2 Expert

    205 Answers

    yadayada
    yadayada

    Level 3 Expert

    75077 Answers

    Are you a Peugeot Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...