Question about 2002 Ford Excursion

1 Answer

How to replacew a backup sensor on a 2002 ford excursion

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 62 Answers

It is very simple to replace the backup sensor. It is a good idea to put on safety glasses or goggles to keep dirt out of your eyes. The easiest way is to lay down under the back of the vehicle and reach up behind the the rear bumper and disconnect the pigtail electrical plug from the suspected faulty sensor(s). Then simply remove the sensor by pushing from inside of bumper toward the rear of the vehicle. If you are not sure which sensor is bad, and if only one sensor is bad, you should check one sensor at a time. And then with the good sensor in place you could test each sensor to see if the vehicle beeps while reversing towards a harmless object (like a traffic cone). Repeat this procedure with the other three sensors and leave the good sensor in place when the back up sensor system works correctly. Hopefully, this will FixYa!

Posted on Oct 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a way i can replace the front clip of a 2002 ford excursion with other truck parts


It looks like the F250 and Excursion use the same part number for the outer fender sheet metal. You can compare part numbers on the link shown and decide if it will work for you
2002 Ford Excursion Fender Replacement Front Driver Side Replacement...

Feb 01, 2015 | 2002 Ford Excursion

1 Answer

What is the recommended gear oil for my 02 excursion?


The Ford recomended fluid is:

Motorcraft SAE

75W-140 Synthetic

Rear Axle

Lubricant
All 3.3L (6.9 pints)

See below for the manual, page 254 shows the capacities info.

2002 Ford Excursion Manual

Hope this helps.

Zeppelinx12

Mar 04, 2011 | 2002 Ford Excursion

1 Answer

Where is the location of the a/c cabin air filter on a 2002 excursion 7.3 L


The 2002 Excursion does not have an A/C cabin air filter. If I can be of further assistance, please come back to FixYa and I will be glad to help.

Sep 16, 2010 | 2002 Ford Excursion

1 Answer

The doors on my ford excursion rattle. how do I


You will have to loosen the striker and slide back, move back in small amounts until door is tight. also make sure its not something inside the door rattling before adjusting the striker.

Jul 20, 2010 | 2002 Ford Excursion

1 Answer

Need 2002 ford excursion schematic transmission


See if these Helm diagrams are what you need.

0be6fb3.png

Mar 17, 2010 | 2002 Ford Excursion

1 Answer

Where's the cruise control fuse located on a 2002 Ford Excursion V10 (Gas)? Stopped working,


Check the Central Junction Box and this diagrams; also can check this in your 2002-Ford-Excursion owners manual.

Fig. Vehicle Speed Control, Page 01 (2002, System overview, Gasoline engines)

f24e465.jpg


Fig. Vehicle Speed Control, Page 02 (2002, System overview, Diesel only)

20f05fd.gif



Fig. Vehicle Speed Control, Page 03 (2002, Gasoline engines)


ac23895.jpg






Fig. Vehicle Speed Control, Page 04 (2002, Gasoline engines)


05a7ea8.jpg





Fig. Vehicle Speed Control, Page 05 (2002, Diesel only)


1b97da1.jpg


Good luck.

Mar 10, 2010 | Ford Excursion Cars & Trucks

1 Answer

2002 excursion 4x4 stalls when stopping had fixed


SOUND LIKE THE IDLE AIR CONTROL OR MASS AIR FLOW SENSOR WILL CAUSE VECHICLE TO STALL OUT.ALSO BAD GASOLINE. BAD COILS OR BAD FUEL INJECTOR.STOPPED UP FUEL FILTER.AND A INTAKE LEAK.MANY THINGS CAN CAUSE VECHICLE TO STALL.

Nov 13, 2009 | 2001 Ford Excursion

1 Answer

How do you replace a speed sensor on a 2002 ford excursion 2 wheel drive?


Depends on which one you have- there are typically 2 types, one mounted on tailshaft of transmission and most likely the one you have, one mounted on the rear end. Replacement is rather easy on both. 1 10mm head bolt and it pulls out. Be sure the new one has an O ring so that it will seal. The one on the rear end is on top of the rearend towards the front of the rear end housing.

Sep 13, 2009 | 2002 Ford Excursion

2 Answers

2005 ford excursion cam sensor location I need to change the cam sensor and the crank sensors on my excursion and i do not know where they are located


On my 02 Excursion with the 7.3L Diesel, the Cam Position Sensor is located at the front bottom of the engine on the passengers side. There is one electrical pigtail plug that is attached and one bolt holds the sensor in position. It may be located in a similar location on your 05 Ex. I do not know where the crank sensor is located. I hope this helps.

Aug 27, 2009 | 2005 Ford Excursion

1 Answer

Error code 0472


try replacing the exhaust back pressure sensor

Feb 04, 2009 | 2002 Ford Excursion

Not finding what you are looking for?
2002 Ford Excursion Logo

1,281 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...