Question about 2001 Dodge Stratus

1 Answer

Put water pump in set the timing to the marks try to start no fire at all

Posted by on

  • 1 more comment 
  • ployal4265 Sep 06, 2010

    We replaced the crank shaft sensor, still no spark

  • ployal4265 Sep 06, 2010

    Replaced the water pump, reset timing, removed valve cover and plantium. Reassembled and now no spark. Replaced the crank sensor. The battery was being charged during this operation.

  • ployal4265 Sep 06, 2010

    We already removed the cam sensor and cleaned it, it looks ok. The engine is the V6 2.7

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 6,826 Answers

I would check the crank shaft sensor,if the timing marks where not on time,the ignition would still spark.

Posted on Sep 05, 2010

  • 2 more comments 
  • Ronny Bennett Sr.
    Ronny Bennett Sr. Sep 06, 2010

    ok,tell,me,what all have you done to the engine.

  • Ronny Bennett Sr.
    Ronny Bennett Sr. Sep 06, 2010

    witch engine does it have?

  • Ronny Bennett Sr.
    Ronny Bennett Sr. Sep 06, 2010

    Remove the cam shaft sensor and clean it on the inside,and make sure it is not broken.

  • Ronny Bennett Sr.
    Ronny Bennett Sr. Sep 06, 2010

    I am not doing you any good,I need to know what all you have already done so not to repeat this process.Have you read any codes?And make sure everything is plugged up,all sensors,and all grounds that where removed.

×

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
bluesman1956
  • 388 Answers

SOURCE: 97 seabring put new water

Where the rotor is facing only tells you what cylinder will fire. To get the #1 cylinder at top dead center you will need to remove that spark plug and place your thumb over the whole. Crank the engine slowly until you feel the compression blow your thumb off the whole. At this point the rotor should be pointing to the #1 cylinder. Please rate this answer, thanks.

Posted on Feb 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Car starts great, warms up then misfires and stalls out. Installed new water pump, timing. This question has been answered but the detail below still pertains to this same issue.


Hi, if you have been talking to somebody, if you reply on the comment link, they will know your asking another question. As far as firing order, whatever cylinder would have to be on compression stroke.
I don't know year--make--model?

May 01, 2016 | Cars & Trucks

1 Answer

After changing the water pump in Saturn and Car still won't start what could it be, acts like it's not getting any fire?


Check the timing belt. If it was removed to change the pump, it may have been put on a tooth or two off, out of time.

Aug 29, 2015 | Saturn Cars & Trucks

1 Answer

Hi, how do I bleed the fuel system on a vw microbus 1997 model 2.5iand how do I know if my timing is correctly set I,


fuel pump working?
injectors spray?
put some fuel 3 spoons in the air inlet and crank the engine
should start for couple of seconds the ignition is ok.
good luck

Dec 04, 2014 | Cars & Trucks

1 Answer

Put water pump on now getting no fire


think you have not put the timing back right and it will need to be re done. hope you used a new belt and adjuster when you put it back together. you need to re line the timing marks on cams and on crank. then put the belt on adjust up making sure the number 1 piston is at the top as well as the timing marks on the cam check this with the crank making, put belt on and adjust up then turn engine one full turn. no spark plugs fitted. back to the timing marks making sure they line up if not re adjust the time until it line back up every time you turn the engine one full turn. then put the spark plugs in etc and start enging.

Oct 15, 2013 | 1992 Oldsmobile Eighty Eight

2 Answers

Changed water pump now wont start battery is charged


If water pump is run by timing belt, the timing will need be reset prior to start up. Make sure timing is adjusted using the timing marks from factory. Check manual to determine timing mark locations.

Jan 20, 2013 | Pontiac Cars & Trucks

2 Answers

I just put a timimg chain an water pump in a 2001 chrysler sebring 2.7 liter engine an it will back firer at start up an not run .no matter how many times i check timing marks everytime it seems to no


I just recently experienced the same problem. The timing is 180 degrees out. Unfortunately the only way to correct it is to take the engine apart again. Set the right hand camshaft to TDC by using the marks on the timing gear for that bank. The left will follow to the degree it can although you will have to manually hold the cam in position when you put the timing gear back on. Now you can remove the timing chain. The crank TDC indicator may not be right on but it will be close. Rotate the crank CW one revolution to the point the TDC marks are lined up. Now install the timing chain according to the instructions. The timing gears on the camshafts will only go on one way as the bolt holes are slightly off the extreme diameter of the gear. If you put the chain back on making sure that all the marks are proper, she'll fire on the second cylinder up. Not a fun job I know, but when everything works right, you do get a sense of satisfaction.

Jul 13, 2012 | 2001 Chrysler Sebring

2 Answers

97 seabring put new water pump on thought i set it back in time all marks line up but no fire rotor button faces number 6 plug not 1


the crank shaft mark is 180 degrees of. It has to be set on the compression stoke. You set yours on the exhaust stroke. Sorry

Feb 04, 2011 | Chrysler Sebring Cars & Trucks

1 Answer

Water pump and timing belt replacement


confirm you timing belt marking at the engine before you start the work. then dismantle all the belt one by one until you reach the timing cover. mark the timing mark again. then start dismantle the timing belt set. after all the belt are out, open the water pump and start to put back the new part by using reverse order from the opening list. make sure the timing marking are the same as you check at the first time. before you start the engine, make sure you turn the engine 2 or 3 round and make sure no part are hitting. good luck.

Nov 19, 2010 | 2002 Isuzu Rodeo

1 Answer

I have a 91 300zx non turbo won't start


Are you sure the new belt didn't jump time? How was the belt tensioner when you replaced yhe belt? Did your water pump leak onto or into your crank sensor?Are you sure you have proper fuel pressure?When you replaced the timing belt, did you make sure to find top dead center on cylinder 1 ? Just lining up the timing marks may not have worked if this is indeed what you did.If you had the crankshaft rotated 180 degrees, your motor would be trying to fire on the exhaust stroke, instead of the compression stroke. To find T.D.C. disconnect your battery,rotate your crankshaft until the piston that is marked #1 in your firing order is at the top of its stroke, this can be accomplished by carefully inserting a wooden or plastic dowel into the sparkplug hole of cylinder#1. The dowel will rise with the piston and at the point where it starts to fall will be T.D.C. Now your timing marks should line up,and you will then be on the compression stroke. good luck! hope this helps

Feb 14, 2010 | 1992 Nissan 300ZX

1 Answer

Honda accord


Unfortunately, u must remove the timing belt. This is why it is recommended to change the water pump when the timing belt is changed.
Here's the procedure : Disconnect neg. battery cable, remove splash shield at wheel well, (after removing wheel to help gain access, turn the engine to align timing marks and set #1 cylinder at top dead center on the COMPRESSION stroke. Once this is done, u can NOT disturb engine or u will have a fun time trying to figure out how the heck to set the timing. Drain anitfreeze, remove timing belt, remove water pump bolts (be aware that bolts may be different lengths, don't mix them up, remove water pump and O ring.
Put it back together: install new O ring and water pump, be careful Oring doesn't slip or move out of position, tighten to 9 ft lbs, install timing belt, refill antifreeze, reconnect battery cable, start car, check for leaks, bleed cooling system, replace splash shield.

Oct 19, 2008 | 1995 Honda Accord

Not finding what you are looking for?
2001 Dodge Stratus Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...