Question about 1989 Dodge Daytona

2 Answers

We can not get all brakes to bleed..what should we be lookin for to fix this

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 2,100 Answers

Is the bleeder screw rusted? You need to start at the right rear wheel, get the right size wrench, a brake wrench would be good. get a piece of hose to fit the bleeder and a soup can to catch the fluid. Pump the pedal a few times to get the pressure up, loosen the bleeder screw and dump it in the can. If you can't get the bleeder screw open, you can use the line itself, Or get some blaster on the bleeder screw and let it set overnight, they will loosen up. Once you do this a few times, and no more air comes out, fill the reservoir and move to the other side rear, do the same thing, then right front, ending up under the reservoir, make sure you keep checking the level. Don't let it **** in more air or you will be doing it again. Hope this helps.

Posted on Sep 05, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 8,516 Answers

Lots of air in line? Try gravity bleed one at a time starting with RR--wide open 'til it drips, then LR, then RF, and LF.

Posted on Sep 05, 2010

  • shelbs_3 Sep 05, 2010

    we tryed that what else could we try

  • Jeff Turcotte
    Jeff Turcotte Sep 06, 2010

    pressure bleed, but you need special equipment. It may be boring and slow, but if you have some pedal, repeating bleed cycles over and over on the same wheel should eventually get the air out. Guy in the car pumps up the pedal and holds down, guy at wheel opens then closes bleeder. do over and over and should eventually get fluid out. Might take 20 times or so, sorry.
    If this doesn't work, you have have a bad master cylinder--or is that what you replaced? What was the original problem, and what did you do to fix it?

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fixed my ABS brakes by replacing two brake lines. Now I get ABS light on dash.Need to erase light. Fixd diagnostics said all is good. Just need to get light off for ABS.


Did you bleed the brakes after you replaced the 2 brake lines. Did you breed the brakes with or with out the power on.The right way to bleed brakes with abs is with thew power off. you will need a abs scan tool and re bleed the brakes

Aug 21, 2017 | Cars & Trucks

2 Answers

Ran out of brake fluid. Have filled it up. Brakes now soft. Do I just bleed brakes?


Yes bleed brakes and look for leaking seals or lines and repair.

Apr 02, 2015 | 2005 Ford Falcon

1 Answer

How do fix C1998 code on 04 expedition abs


anytime you open a brake system you should bleed the back furtherst away first then the work forward , easy

Dec 02, 2014 | 2004 Ford Expedition

1 Answer

I'm trying to bleed my clutch in my 2000 camaro ss. I finally found the the bleeder screw at the top of the transmission on the drivers side. Just lookin for some guidance from here forward.


Adam: fill the slave cylinder resivour with fluid attach a bleeder hose to
the port have someone pump the clutch pedal u ntil fluid runs thru
without any air bubbles in it depending on the amount of air in the line
and NO other leaks this may take a few fills.

Jan 30, 2013 | Cars & Trucks

1 Answer

Cant bleed front brake on honda foresight 2001


Try opening the bleeder and just let it gravity bleed is what I would try.

Jun 16, 2012 | Cars & Trucks

1 Answer

I hav a 1984 porsche 944 n the clutch petal is on the floor what am i lookin for that would cause this to happen is it a clutch cable set up or is it a hydrolic set up ???


hello there
first thing you check you brake fluid level if is too low that would create air in the system .
It is part of brake fluid reservoir
when you fill it you need to bleed the system at the sleve cyllinder which operates the clutch arm .
it is by the transmission

proporsche.

Dec 27, 2010 | 1984 Porsche 944

1 Answer

I have replaced all brake parts including front brake hoses and let all the brake fluid to drain out of the master cylinder. Went to bleed the brakes and it appeared to bleed all air out of the lines etc.....


U forgot to bleed the BRAKE MASTER! When ur bleeding the brakes, make sure ur engine is RUNNiNG. I f u haven't got any BLEEDiNG tools that sucks all the fluid in ur car, try Bleeding first the master, 2nd will be the front wheel brakes, and the REAR brakes! If everything FAiLS go to ur nearest garage and have them fix it! Drive slowly, using ur engine and hand brake! Hope that helps u out!

Nov 17, 2010 | 1990 GMC S-15 Jimmy

3 Answers

Brakes go to the floor after replacing them and the abs light comes on. we are lookin for a tonjng sensor that was bumped


when you say you fitted new brakes do you mean you replaced the brake pads or do you mean opened the fluid system in anyway if you did needs blead if not and only pads were replaced then the pedal needs pumped with you foot and keep pumping until the pedal comes back and do not go on public road until that pedal come back,engine running is better when doing this,you say the tonjng sensor was bumped if your sure it bumped then replace it.adrian,,,,,,,,,

Aug 19, 2010 | 2004 Dodge Durango

1 Answer

Brakes


The brakes just need to be bled properly which take 2 people or a bleeding pump,Please tell me how you are bleeding the brakes.

May 17, 2009 | 1998 Audi A4

Not finding what you are looking for?
Cars & Trucks Logo

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...