Question about Toyota RAV4

Open Question

How we repair shift solenoid malfunction code P0750 for toyota rav4

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

frcs68
  • 1605 Answers

SOURCE: Repair Codes - B2796, P0750 and P0420.

B2796 is no communication in Immobiliser system, which means you or some one else try to use a key transponder to start the car.
you need some one to clear that code. it doen't affect the car performance.
P0750 is shift Solenoid malfunction, you hsould have engine management light on the dash. this you can call the dealer, I believe this is cover by Toyota service bulletin.
http://www.mediafire.com/?jjmootmytfz
P0420 is O2 oxygen sensors.Toyota has issued a service bulletin regarding the P0420 trouble code that could apply to your vehicle, to be sure if this bulletin applies to your car I will need the VIN# and e-mail to tedrttr@yahoo.com with that information.

Posted on May 19, 2009

moparownr
  • 667 Answers

SOURCE: TRANSMISSION PROBLEM

You have a shift solenoid problem, it will probably have to be replaced, it will require taking off the transmission oil pan (draining trans oil), I recommend that you leave this task to a repair shop, it is a little tricky to do and it is very important that the inside of the transmission stays very clean. I hope this helps you, please let me know

Posted on Jun 03, 2009

  • 142 Answers

SOURCE: What does code P0753 Shift Solenoid mean?

P0753 means your powertrain computer detects a continuous open, short to ground or short to power in the circuit to your transmission's 1-2 shift solenoid. When the code is active, your transmission runs in a fail safe/limp home mode that only lets certain gear ratios function in the transmission.

The solenoid in your application looks like this
1edc2e6.jpg and it is located sometimes on the side of the transmission, but my guess is from the looks of it, it might be found inside the transmission, only accessible with the oil pan removed.
The problem might be the solenoid itself, or the wiring going to the solenoid from the computer that controls the transmission, or the computer itself.

Posted on Sep 09, 2009

  • 1 Answer

SOURCE: P0760 Shift Solenoid C Malfunction

Possible wiring problem on shift solenoid c on my 2002 Montero Sport. Mechanic replaced tranny on the truck and said that it has a wiring issue and he doesn't think it can be fixed. Truck only has 65K on it with rebuilt tranny,what can be done?

Posted on Nov 24, 2009

  • 1 Answer

SOURCE: P0750 shift solenoid A malfunction

where the shift solenoide locate inside the transmission?

Posted on Sep 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bad transmition, the car wonte will not go in drive or reverse, just revs up real high


code p0743 refers to torque converter clutch solenoid-electrical=== causes wiring--clutch solenoid ECM/TCM
code p0750 refers to shift solenoid--A circuit malfunction=== causes wiring --- shift solenoid --ECM/TCM
code p0755 refers to shift solenoid B --circuit malfunction=== causes -- wiring---shift solenoid ---ECM/TCM
First is to check the wiring and connections are in good condition. next is to replace the clutch solenoid for the torque converter and work up from there

Jun 06, 2013 | Mazda 626 Cars & Trucks

1 Answer

What are these codes in toyota rav 4 PO171 PO105 PO760 PO 770 PO130 PO171


OBD=11
code p0171 refers to system to lean---causes ---intake/ exhaust leak---air system---MAF/VAF sensor---fuel pressure/ pump---injectors HO2s
code po105 refers to manifold absolute pressure (MAP) sensor/bar ometric sensor and circuit malfunction causes---wiring---MAP sensor ECM
code p0760 refers to shift solenoid--circuit malfunction causes--shift solenoid---ECM?TCM
code po770 again refers to shift solenoid.
code p0171 again refers to shift solenoid ---performance or stuck off.
code po130 refers to heated oxygen sensor HOS2 1 bank 1-circuit and have the rest checked .malfunction -- causes---heating inoperative---poor connection---wiring--- HO2S. So replace the shift solenoid and oxygen sensor

Apr 22, 2013 | 1996 Toyota RAV4

1 Answer

2005 Dodge RAM 1500 Quad Cab; 5.7 Hemi: Trouble codes: P1521 Transmission Engaged at High Throttle Angle P0700 Transmission Control System Malfunction P0750 Shift Solenoid A Malfunction Truck feels...


P1521 - VRIS Solenoid 1 I have replaced the VRIS (Variable resonance idle solenoid 1).
P0750 - Shift Solenoid A malfunction
There is more than one solenoid in the valve body and to make sure he is replacing the right one. I will say that with an electrical malfunction code---it's usually the wiring or the solenoid----so not a real bad choice. Come to think of it I think there will be 4 solenoids---A,B,EPC and TCC. So he needs to find out which one is the bad one before he goes replacing.

Good luck

Aug 16, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

O/d light blinks when driveing o/d seems to be engaged car has 198000 miles and runs very good also engine light is on


O/D light blinks, but with that the check engine light is ON.--- This will make your troubleshooting easier.When the check engine light comes on, and remains on, this indicates that there is error stored in your cars computer.---- Once the computer is scanned, you will get error codes, as per that error code it will point towards faulty part, which is causing the O/D light to blink.-------- Most probably the O/D light blinks, If a problem exists in No. 1 or No. 2 solenoids or speed sensors .
--------------- For car after 1995 it requires OBD2 tool and for car before 1995 it requires OBD1 tool.------- --------- You car will require OBD1 tool.There are very few auto parts store and repair centers who have OBD1 tool.In your case you required OBD1 tool.------ You can just contact local auto-parts store and they will guide you to the nearest store who has OBD1 tool.There you can get your car scanned.If there is error set in your cars computer, then you will receive the error code.As per error code it will point towards the faulty part causing this problem in your car.------------- -------------- The codes which you get is scanning will be mostly any of this following codes:--- DTC P0500 - Vehicle Speed Sensor Malfunction
. DTC P0750 - Shift Solenoid "A" Malfunction
. DTC P0753 - Shift Solenoid "A" Electrical Malfunction
. DTC P0755 - Shift Solenoid "B" Malfunction
. DTC P0758 - Shift Solenoid "B" Electrical Malfunction
. DTC P0770 - Shift Solenoid "E" (SL) Malfunction
. DTC P0773 - Shift Solenoid "E" (SL) Electrical Malfunction
. DTC P1520 - Stop Light Switch Signal Malfunction
. DTC P1705 - Direct Clutch Speed Sensor Circuit Malfunction
. DTC P1765 - Shift Solenoid Valve SLN Circuit Malfunction
. DTC P1780 - Park/Neutral Position Switch Malfunction
--------------- Now it all depends on what code you get, as per that you can replace the following part.------- This will help.Thanks.Helpmech.

Jul 07, 2011 | 1995 Toyota Camry

2 Answers

Code P0700 and code P0750 what do i have too change


P0700 Transmission Control System Malfunction
P0750 Shift Solenoid A Malfunction

It seems you have a internal transmission problem, I suggest you have your transmission inspected by a reputable transmission shop.

Jun 04, 2010 | 2004 Dodge Durango

2 Answers

Van quit moving all at once fluid clean no burnt


P0743 Torque Converter Clutch Circuit Electrical
P0750 Shift Solenoid A Malfunction
P0760 Shift Solenoid C Malfunction
check all the ground wires on the harness look for broken wires or a plug pulled out

Mar 24, 2010 | 2004 Ford Freestar

1 Answer

Repair Codes - B2796, P0750 and P0420.


B2796 is no communication in Immobiliser system, which means you or some one else try to use a key transponder to start the car.
you need some one to clear that code. it doen't affect the car performance.
P0750 is shift Solenoid malfunction, you hsould have engine management light on the dash. this you can call the dealer, I believe this is cover by Toyota service bulletin.
http://www.mediafire.com/?jjmootmytfz
P0420 is O2 oxygen sensors.Toyota has issued a service bulletin regarding the P0420 trouble code that could apply to your vehicle, to be sure if this bulletin applies to your car I will need the VIN# and e-mail to tedrttr@yahoo.com with that information.

May 19, 2009 | 2002 Toyota Camry

1 Answer

P0750 shift solenoid A malfunction ?


where the shift solenoide locate inside the transmission?

May 08, 2009 | 2002 Toyota RAV4

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

978 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...