Question about 2006 Chrysler 300

1 Answer

Need to replace the tail light cover for Chrysler 300, driver side. Bulbs are ok. Clear part of cover assembly is broken. How do I do that?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 172 Answers

Generally, the cover, lens, and reflector assembly are all one piece (glued together) and you must replace the entire assembly. I would check with an auto recycler (junkyard) for this, as I'm sure the dealer wants a small fortune for it.
If you open the trunk and (if needed) remove the liner, as if you are going to replace the bulbs, you will be able to see the fasteners around the perimeter of the reflector. They may be screws, they may be some kind of clip or push-pull fastener, depends on the model. Remove all the bulb sockets (label them for the correct position) then remove the fasteners, remove the lens assembly (usually pushes out toward the back of the car), then reverse to install the new one.
You may need some sealant around the perimeter of the lens assembly (to keep water out of the trunk), you can use kitchen and bath silicone caulk.

Posted on Sep 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the broken tail assembly on my 2012 Honda Accord so I can replace it with the new assembly ?


Have you tried going into the trunk and removing the panels covering the lights inside?
Hope this helps.

Feb 25, 2015 | Honda Cars & Trucks

1 Answer

I have a 2005 Chrysler Pacifica my driver side tail light and front amber light don't work passenger side works fine bulbs aren't burnt out


have the fuse box checked ,drivers side lower dash the cover should give list of fuse location , if ok check the wiring from the light fitting to the earth wire connection to the body/chassis,make sure this is a good connection , the bulb holders themselves can sometimes get brittle over time so the bulb may be fine but might need removing and refitting checking that the contacts are meeting etc ,keep me posted if you wish

May 12, 2014 | Cars & Trucks

1 Answer

How to replace brake light bulb audi a4 1.8t 2002


Start by opening the trunk lid. On the sides of the trunk, just beside where the trunk lid sits when closed there is a circle cap on either side. Remove the cap it is the same material as the trunk side trim (fuzzy carpet) then there will be a screw set into the hole that you just uncovered. You can use either a philips screw driver or an 8mm socket and remove the screw/bolt. you may need to reach in with a set of needle nose pliers to remove the screw after it is loosened all the way. Once the screw is removed grab the tail lamp assembly from the inside and twist the tail lamp out of the holding pins located on the side edge of the tail lamp. The whole light will come off of the body in your hands. Once the tail lamp assembly is out there is an access panel on the back side where all the bulbs are installed. Depress the two holding tabs on the sides and carefully remove the bulb holder. Then replace any blown bulbs and reinstall.

Jan 17, 2014 | 2006 Chrysler PT Cruiser

1 Answer

Tail light lens replace


Not clear on make or model. Generally the tail light assembly is accessible from the trunck. May have to unscrew or remove bracket to gain access. Most lens covers are held in place by series of clips. Carefully remove clips and the existing lens should come out. May need second person to position replacement lens cover from outside while you secure from inside trunck.

Jan 26, 2012 | 2008 Chrysler 300

3 Answers

Tail lights do not work on a 2000 lexus rx 300 bulbs are fine, all other lights work fine


You may have a fried fuse. Look in your owners manual to find out which fuse it is in the fuse box diagram. If that is the problem make sure to use the same amperage fuse to replace the burned one with. I fried fuse is usually a sign that you have a short somewhere. But they can also fry for other reasons such as excess moisture somewhere. Sometimes they just burn from age and fatigue. It may solve it to just replace the fuse, but if there really is a short, the new fuse will fry too.

Dec 29, 2010 | 2000 Lexus RX 300

1 Answer

Tail light burned out. How to get tail light cover off to replace it?


There are 2 screws holding the light assembly. You need a special star shaped screw driver to take them out. Then the assembly pulls out straight back. Next, the cover plate comes off exposing the bulbs. If I remember correctly, it is a 3057 bulb.

Dec 18, 2010 | 2000 Oldsmobile Silhouette

1 Answer

How do i replace the tail light bulb


pop the trunk and look at the trim directly behind the light assembly. If you're lucky, then it'll have an opening for you to take out the bulbs from inside.

Otherwise (most likely with NA Cars), you'll have to remove the screws holding the taillight assembly down and pull it off the car to get to the sockets of the bulbs

Sep 08, 2009 | 2005 Chrysler 300

1 Answer

'01 Lexus GS 300,My dash tail lights warning just


check you tail bulbs as you have a broken circuit

Jun 10, 2009 | 1992 Lexus Ls 400

2 Answers

How to replace tail light


First you need to lift the hatch. There are two screws under plastic caps. Remove the caps and you will be able to unscrew these screws. Carefully using a flat screw driver to pry out the tail light assembly. It have to plastic pin that attached to the car body. do not break the pin. After you pry out the tail light assembly, you will be able to replace the light bulb. Replace everything in a reverse order.

Nov 17, 2008 | 1999 Lexus RX 300

Not finding what you are looking for?
2006 Chrysler 300 Logo

279 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

77544 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...