Question about 1996 Volkswagen Golf

1 Answer

My car either cuts out or dont start at all . its like a switch has been flicked

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

Reset the alarm,if you dont know how get back.....

Posted on Sep 05, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Cut out wont restart,power light flicks on briefly(so not the fuse!) poss main switch?

what is year--make--model? Can you check for applicable trouble codes?

May 12, 2015 | Cars & Trucks

1 Answer

Can I turn off the beeping on my Rav4 (2013) while the rear hatch is open?

Hi there
Yes if you look in the book you will find the wire code for the rear buzzer then cut the wire and fit a flick switch in between the cut wires BUT dont forget to turn it back on again after.

Aug 23, 2014 | 2013 Toyota RAV4

1 Answer

Why are my headlights cutting out when i turn my high beams on?

The problem will be due to a malfunctioning headlight dimmer switch and a dimmer switch connector. Also check the high beam connector.

Jul 14, 2013 | Ford Futura Cars & Trucks

1 Answer

Theft switch under dashboard

is this a question ?

it shuld be 2 wires going to it 1 in 1 out the flick switch will allow power through if switched on if not it cuts the circuit

u can buy switches from most good car shops

ull want a 2 position togle switch on / off

it would be a good idea to take ur old switch to the shop as sizes and styles vary

Oct 30, 2012 | 1994 Toyota Camry

1 Answer

My car cuts out when i flick it over to lpg any answers?

check power to gas lock valves check gauge switch. check saftey switch

Aug 01, 2010 | 1995 Land Rover Discovery

2 Answers

My 1997 jeep Cherokee will only run for about 3 seconds because the immobilizer needs resetting how do i do this.

i just put an earth switching solenoid on mine. cuts the earth to the whole car. when i want to start car, i just flick switch, to activate earth and start the car. this is a solution if ya got no money or live like i do 1000kms from the nearest dealer.

May 08, 2010 | 1997 Jeep Cherokee

1 Answer

My high beams dont work.

high beam switch is faulty look at getting a new stalk.....

Aug 25, 2009 | 1990 Toyota Land Cruiser

1 Answer

Automatic car starter

Check the hood pin it is usually place by the battery make sure it is not bent or damaged. Then shot off the toggle shitch and disconnect the battery and reconnect it, turn the toggle back on see if it resets. Good luck

Aug 03, 2009 | 1998 Toyota Corolla

2 Answers

My car alarm is blinking but the remote doesn't work. I already replaced the battery to the remote so I know that's not the problem. If I open the car the alarm goes off and doesn't allow me to start the...

You need to first look under the drivers side dash area near the hood release/fuse panel area and see if there is a valet switch. The switch will look like a little toggle or a push switch. After you locate it, turn the ignition switch to the on position(dont start it) and flick the valet to the opposite position it is in now. If done correctly in most cases the red system light will stay a constant instead of off or blinking indicating you are in valet mode. Next try to start the engine. If this doesnt work you need to remove the alarm system and repair the ignition switch wiring or replace the electrical portion of the ignition switch. The aftermarket alarm cuts into the ignition switch wires and bypasses the start circuit through the alarm module. When disarmed the alarm completes the circuit and allows the car to start. Good luck hope this helps and please rate this.

Nov 05, 2008 | 1997 Nissan.5 Altima

Not finding what you are looking for?
1996 Volkswagen Golf Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

80417 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides