Question about 2006 Jeep Commander

1 Answer

What type of antifreeze do i use for 2006 jeep commander

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Jeep Master
  • 76,164 Answers

Use any brand marked as "LONG LIFE OR EXTENDED LIFE COOLANT"

Posted on Sep 05, 2010

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Gozer
  • 435 Answers

SOURCE: install a altenator for a 2006 jeep commander

I would rate this a 5 in difficulty. If you have a metric socket set, basic hand tools and a supertine belt tool it's fairly easy repair. You can rent a surpentine belt tool at Autozone.

Disconnect the battery
remove the cowling
remove the supertine belt from the altenator pully
disconnect the red wire on the back of the altenator
disconnect the harness plug from the altenator
remove the bolts holding the altenator to the mounting brackets.
Reverse the process with the new altenator and it it's done.
Make sure your battery is charged before you start the engine a low battery can cause damage to your new altenator.

Posted on May 21, 2010

greg_margo
  • 1959 Answers

SOURCE: Jeep Commander Rear Brake Pad Installation

Per Chilton Auto repair manual:

Removal & Installation

  1. Raise and safely support the vehicle.
  2. Remove the rear wheel.
  3. Siphon a small amount of brake fluid from the master cylinder reservoir.
  4. Insert a small prybar through the caliper opening and pry the caliper cover (using the outboard brake pad) to bottom the piston in the caliper bore.
  5. Remove the caliper slide bolts.
  6. Remove the caliper from the anchor.

    WARNING Support the brake caliper with mechanics wire. Do not let the caliper hang by the brake hose.
  7. Remove the brake pads from the caliper.
To install:
  1. Install the brake pads onto the caliper.
  2. Lubricate the slide pin bolts with grease provided with the brake pads, or suitable silicon grease equivalent.
  3. Install the caliper on the anchor and tighten the slide pin bolts to 18 ft. lbs. (25 Nm).
  4. Install the rear wheel.
  5. Lower the vehicle.
  6. Pump the brake pedal several times until a firm pedal is obtained in order to properly seat the pads.
  7. Refill the brake fluid reservoir to the proper level.

Posted on May 17, 2009

  • 645 Answers

SOURCE: ac/heater fan switch problem on a 2006 jeep commander

next to the fan motor there should be a connector that has three or four wires that attached to the blower resistor. it should have two screws holding it to heater case, just pull it out and replace.

Posted on Feb 13, 2010

Testimonial: "This info was very helpful but need a little more info of where the fan motor is located. I will post another question to find that info."

alicantecoli
  • 22156 Answers

SOURCE: 2006 Jeep Commander inefficient catalyst

most likely the oxygen sensors (lambada) ,they need changing ,their are two one before the cat and one after,do not think you need a new cat unless it has a min of 150.000 miles on the clock

Posted on Jul 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Jeep Commander seems stuck in 4wd. Dash displays service 4wd system, but doesn't throw a code.


google jeep commander forums join a few of them and post question there

Feb 05, 2013 | 2006 Jeep Commander

1 Answer

Leaking thermostat housing. New Housing or gasket or both?


without taking it off its difficult to say but if its a plastic housing then renew it as these plastic housings to tend to crack with age and dont forget the antifreeze

Mar 22, 2011 | 2006 Jeep Commander

1 Answer

2006 Jeep Commander dash display reports "Service


It cant hurt to check your spare. It may need a bit more air.

:)

Dec 19, 2010 | 2006 Jeep Commander

1 Answer

Starter repair estimate 2006 jeep commander


Check here for parts replacement and "How to": Jeep/Commander/Replacement/Starter

Hope helps (remember rated this).

Jul 07, 2010 | 2006 Jeep Commander

1 Answer

2006 Jeep Commander inefficient catalyst


most likely the oxygen sensors (lambada) ,they need changing ,their are two one before the cat and one after,do not think you need a new cat unless it has a min of 150.000 miles on the clock

Jul 02, 2010 | 2006 Jeep Commander

1 Answer

2006 Jeep Commander lost instrument panel power


check all fuses and battery connections start there.

Oct 13, 2009 | 2006 Jeep Commander

1 Answer

2006 Jeep Commander Scheduled Maintenace


Your Jeep dealer should be able to get you that

Mar 20, 2009 | 2006 Jeep Commander

Not finding what you are looking for?
2006 Jeep Commander Logo

Related Topics:

1,124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...