Question about 2003 Ford F250 Super Duty Crew Cab

3 Answers

How do you change front side marker lightbulbs???

Posted by on

  • 2 more comments 
  • mehickey Sep 05, 2010

    its not the bulb,its the case surrounding the bulb, do you have to take the entire grill off? This is very difficult, do you take your tire off and go throught the hub?

  • mehickey Sep 05, 2010

    It is the running light on the passenger side that needs to be replaced, and we cannot get the cover off to get to the bulb - what is the secret??????

  • mehickey Sep 05, 2010

    That does not work - I cannot get my hand up there between the lining to change the bulb, I am giving up and going to a body shop. I have called 2 different auto parts store with no help. This was my last resort and a waste of time!

  • mehickey Sep 07, 2010

    i can't even see how you would take the light assembly off! I can see where the light plugs in, there aren't even screws to take the assembly off! A body man told me today ,they may have built those trucks to sell, but not to work on! This cite was a waste of my money!!!!

×

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,016 Answers

Hi,

Which marker lamps?

The side marker lamps on the tray?

If they are the side marker lamps then you need to remove the lamp assembly and then replace the whole lamp assembly, they are sealed units.

Hope this helped, let me know if you need more information.

Thanks

Jason

Posted on Sep 06, 2010

  • Jason Maurirere
    Jason Maurirere Sep 08, 2010

    Hi,

    Is this the lamp assembly you are talking about?



    Let me know.

×

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 76,848 Answers

Go inside the front fender wheel well linings to access the bulbs

Posted on Sep 05, 2010

×

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,044 Answers

You have to get to them from the bottom. you should be able to reach the bulb connector. Give it a half twist counter clockwise turn and pull out. The bulb is most likely a push in type bulb but you should be able to see what holds it in place. Reverse the process to put everything back in place.

Posted on Sep 05, 2010

  • James Young Sep 08, 2010

    Only other advise I can give you is to pop the inside fender well covering off to reach it if it's there. If you can't reach it from the top and you can't reach it from the bottom and there are no screws or pressure clips you can release to remove the assembly to access the bulb then your most likely looking at the wrong area. There are no vehicles that have bulbs that are not accessible unless it is a reflector in which case there is no bulb. Even Diode assemblies can be removed fairly easily to replace them. Trace the wires that lead to the light down and make sure your in the correct area. I've been doing these type of jobs for about 30 years, I know what your trying to do and there are only so many ways to do it.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to get front marker housing light off


change your light switch and you have to remove your headlight to take out the marker light

Apr 18, 2014 | 1994 Honda Accord

2 Answers

How to replace a front side marker bulb on a 2007 Toyota Yaris Sedan


You don't need a dealer for much of anything

All of todays vehicles require removing the lamp
assembly or housings,front or rear, of any vehicle,to
take out the lamps/bulbs

If you open the hood you will find screws that hold it in place

May not be an easy job, but that's the junk were sold

Sep 05, 2012 | 2007 Toyota Yaris

1 Answer

Change front turn signal


The side marker light must be removed in order to get at the turn signal light.
There are two screws holding the side marker light which is situated above the turn signal.
Open the hood.
Remove the phillips head screw at the top of the side marker light.
Using a long #2 Phillips screwdriver, remove the screw on the outside of the side marker light. This can be seen by looking between the lower side of the side marker light and the top side of the turn signal.
The side marker can be moved.
The turn signal has one screw on the top of the fixture that must be removed.
Slide out the turn signal fixture. There is a small feature on the lower front corner of the turn signal fixture that you must note to properly reinstall the turn signal.
In order to get to the bulb, rotate the bulb socket 1/4 turn CW or CCW. The bulb socket is loose.
The bulb is simply pressed into the socket.
Not sure of the type, but it can be found at your locale auto parts store.
The bulb is used in several places on the 1994 GC, so get apacket with two, if possible.
Assembly in reverse. Be careful not to overtighten the screws as they are replaced.

Mar 29, 2011 | 1994 Jeep Grand Cherokee

2 Answers

My rear marker/ running lights are out and i need to know how to get to them


Signal and Marker Lights Removal & Installation To Remove:
  1. Remove or disconnect the following:
    • Screw from the side marker lamp.
    • Side marker lamp from the front and/or rear bumper fascia.
    • Bulb/socket from the side marker lamp.
    • Bulb from the socket.
To Install:
  1. Install or connect the following:
    • Bulb to the socket.
    • Bulb/socket to the side marker lamp.
    • Side marker lamp to the front and/or rear bumper fascia.
    • Screw to the side marker lamp. Tighten to 2 N.m (18 lb in ).
prev.gif next.gif

Jan 08, 2011 | 2002 Pontiac Sunfire

1 Answer

How do I change the front side marker light bulbs?


Bi-Xenons - 6000K D1S
High Beams - Osram Nightbreakers H7
Fogs - PIAA H11 Yellow Ion
Cornering Lights - Osram Nightbreakers H3
Front Park Lights - High-Powered LEDs with built-in resistors
Front Signal Lights - Sylvania Silverstar 7507A ST (Silver Bluish but lights up Amber)
Front Sidemarkers - InviSilver W5W (Silver but lights up Amber)
Rear Signal Lights - P21W Stealth Bulbs (Silver but lights up Amber)
Reverse Lights - Sylvania Silverstar 7506ST or Error-Free LEDs
License Plate Lights - C5W Error-Free High-Powered LEDs
  • Turn the engine off and approach the side of the porsch with the burn-out side-marker light. If you are replacing both, start at either side; the replacement procedure is the same.
  • 2 Remove the screws from the plastic fender liner. Peel back the liner to access the area behind the fender.
  • 3 Reach your hand inside to gain access to the side-marker light's backing. Push the backing forward to release the side-marker lens; it's held in place by small clips.
  • 4 Grab the lens on the outer side and turn it over to access the back. Gently turn the bulb to release it from the plastic lens.
  • 5 Pull the bulb straight out to remove it from the electrical socket. Insert a new bulb, but do not touch the glass part of the bulb with your hand.
  • 6 Push the new bulb into the side-marker lens. Turn it clockwise to install it. Push the side-marker lens back into place. Apply gentle pressure to the lens to pop it back into its mount.
  • 7 Replace the screws along the edge of the fender liner.


  • Dec 04, 2010 | 2006 Porsche Cayenne

    2 Answers

    How to change the little front lights beside the main front light


    Side Marker Lights
    1. If visible, remove the attaching screws and partially remove the front side marker light lens.
    Fig. 7: To change a side marker bulb with no attaching screw, protect the body with a rag and gently pry the lens assembly outward . . .





    Fig. 8: . . . until the entire assembly is free of the body and access to the bulb socket is achieved


    2d8805f.jpgde76af4.jpg

    Aug 30, 2009 | 1994 Mazda 323

    1 Answer

    How do you replace the front side marker lightbulb on a 2005 chevy silverado??


    Remove headlight you will see 1 ( see pic) rods on top of the headlight you are going to turn them then pull up on the rods the pull out on the headlight.The look at the back side of the marker light and you will see a tab on left side push it the lenses will come out.25fd5df.gif

    Jun 27, 2009 | 2005 Chevrolet Silverado

    3 Answers

    Replace parking/marker bulb front pass 98 Jeep Grand Cherokee


    look in between the marker and headlights its a screw there screw it out

    Apr 04, 2009 | 1998 Jeep Grand Cherokee

    1 Answer

    I ned to change left side marker light up front bulb 194na how do i get assembly out on 1996 mercury grand marquis


    I changed the front left marker light on side of headlight assembly by unscrewing the screw on the far back of it. then i just pulled it off. it felt like it was gonna break but it came off just fine

    Mar 22, 2009 | 1996 Mercury Grand Marquis

    1 Answer

    How to change front driver side 2004 g35 coupe marker light


    Just pop out the side marker from where the marker meets the fender well and push outward on the side marker. It has a metal clip retaining it to the bumper.

    This entry was in January, most likely you figured it out already.

    Jan 19, 2009 | 2004 Infiniti G35 Sport Coupe

    Not finding what you are looking for?
    2003 Ford F250 Super Duty Crew Cab Logo

    Related Topics:

    135 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    76848 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    fordexpert

    Level 3 Expert

    5546 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...