Question about 2001 Chrysler Town & Country

1 Answer

Turn over but wont start no fuel to cylinders

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Chrysler Master
  • 76,673 Answers

Have the electric fuel pump tested for correct pressure, sounds like the fuel pump is defective.

Posted on Sep 05, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What are the possible reasons why the engine wont start ?

this sounds like no fuel to cylinders , could be an air lock so i'd suggest starting with the fuel lines and work forward , can't be more specific as you havent mention vehicle , model , year etc

Jul 13, 2015 | Cars & Trucks

1 Answer

94 jeep grand cherokee ltd 5.2l, wont start, turns over, smells like fresh fuel, has backfired from exhaust, replaced spark plugs (fuel fouled and dirty) and has worked for about a week and gradually...

You are saying the injectors are allowing too much fuel into the cylinders. Or not enough air from the air filter.
Is the check engine light on, and have you checked the fuel pressure regulator ?

Jan 15, 2014 | 1994 Jeep Grand Cherokee

2 Answers

2003 gmc savanna, fuel pump wont work, installed new punp and ignition cylinder, turns over but wont start. I put the key to on position and let it sit for 15 min and still wont start

Check pwr to pump with test light while somebody turns key on and off, if pwr check ground from pump to frame, if no pwr check fuel pump relay

Nov 03, 2013 | 1999 Cadillac Eldorado

1 Answer

Have new ignition lock cylinder but car wont start

The lock cylinder only lets the key turn to enable the ignition switch. The only way the lock cylinder would prevent the car from starting is if it no logger turned or it was tied into the security system. What engine do you have and what are the symptoms? Can you hear the starter turning the engine over? Have you checked for fuel and spark? Is the battery charged? Etc.

Sep 08, 2013 | 2001 Mitsubishi Eclipse

1 Answer

94 chevy s10 4.3 engine wont start but it will turn over has fuel pressure and when you spray a little gas in the intake it cranks up but then stops

fuel starvation ie blocked filter /blocked pipe / as no fuel is reaching the cylinders

Aug 17, 2012 | Chevrolet Chevy Cars & Trucks

1 Answer

1995 blazer cylinder full of fuel. starter wont engage changed fuel pressure regulator.. ran great then wouldnt start

Check oil at dipstick for too much gas in oil thinning it to the point where the engine seized and won't turn over. If the cylinder was full of gas, this is a possibility. If the cylinder was full of gas, the fuel injector(s) might be stuck open causing this problem. Good luck on this problem.

Oct 26, 2011 | 1996 Chevrolet Blazer

3 Answers

Ok replaced the intake manifold , car wont start, checked crank sensor, checked plugs and wires. fuses, fuel injectors ,engnition sensor bad , replaced it coil packs good and still wont start .getting...

or you getting the right fuel pressure? check fluid filter, check pressure regulator, check spark plugs to see if they are soaking wet if they or wet take them all out and pull fuel pump relay out turn engine over and blow all gas out the plug holes. install plugs and relay and try start again , check engine compression, check coolant senor ,check cam sensor

Jul 06, 2011 | 1999 Pontiac Grand Prix

2 Answers

My 2000 Oldsmobile intrigue wont start it was hard 2 start 4 months and now it wont start

If it is not cranking, you must check for battery voltage, if it is cranking you must check for ignition (spark) and verify fuel pressure and fuel delivery to the cylinders.

Mar 12, 2011 | 2000 Oldsmobile Intrigue

1 Answer

My 2000 hyandai elantra started slowing down by itself and filled with gas fumes inside. We changed the fuel filter and it will not turn over to start. It will also not roll start.

If you got a strong oder of fuel in the cab. I would say you have a sever fuel leak. Check for fuel leaks. Now if when you say it wont turn over and you mean the engine wont crank over. Then you might want to pull some of the plugs just to make sure the cylinders are not full of fuel. if that be the case you have some leaking injectors

Mar 25, 2010 | 2000 Hyundai Elantra

Not finding what you are looking for?
2001 Chrysler Town & Country Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides