Question about 2005 Volvo S60

Open Question

How do you remove the center console cupholders module from an '04 S60? I can get to the driver's side screw, but can't get to the front and passenger side screws.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: how to remove front door

Pop the grab handle cover off, two different styles.

1. With a slot under the grab handle, take a small screw driver off and gently push up, it should just pop out.

2. Simple cover that can be separated with a bone tool or similar so you don't chip the cover piece.

Behind that you will find two Torx 25 screws, Take those out.

Around the edge of the panel should be around 8 plastic rivet type of thing.

Again...two different styles.

1. With center pins that blend in perfectly with the rivet. Should be about 3/32nds diameter. Push the center in and the rivet deals should pop out. Be sure not to lose the center piece...easy to lose.

2. Same deal but with a larger center pin.

Take the plastic triangle piece near the upper right hand area as facing the panel.

Pull bottom away from door and up to release from top section of door.

Careful removing the cable for the door lock release, and remove the connectors from the tweeter and driver's door module.

Posted on Aug 14, 2008

  • 651 Answers

SOURCE: I cannot remove the CDplayer from my 1999 TWIN CAM HYUNDAI EXCEL

try pulling it out, it should come out far enough to get at the screws. they got it in there without removing all the other stuff, so it has to come out. you may need to purchase a removel tool at a local parts store, there are several differant kinds so ask someone at the store to look at it. they should be able to tell you which one you need. they only cost a couple dollars.

Posted on Dec 29, 2008

motor1258
  • 6674 Answers

SOURCE: How to remove cupholder console on 2003 Explorer

did you try just sticking meter probe or test light probe in the hole,dead center at back for indication of power to it? Careful not to touch sides if using test light, you will blow a fuse. Steady hand.

Posted on Jan 04, 2009

co7196
  • 3433 Answers

SOURCE: 04' xc90 passenger side vents not putting out a/c

Hissing is a vacuum leak. Loose hose, or defective actuator ar vent shutter.

Posted on Jun 02, 2009

co7196
  • 3433 Answers

SOURCE: stuck front passenger seat - wont slide back or forwards due to small screw lodged in floor runner

Be there done that, but with a penny. All you can do is either get real aggressive with a hammer and long metal object as a punch or pull the seat. The seat should have 4 bolts. One at each end of each track. Ising a 1/4 in drive rachet and either a 1/2 or 9/16 socket should work. 1/4 in drive is low profile.. good luck

Posted on Jun 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the center console of a Isuzu Ascender


why not read on alldata.com, its all there,
remove a screw?


25402002-5afre3fjdbg1gkzo1rpx5eib-3-0.jpg
  1. Block the wheels to prevent the vehicle from moving.
  2. Remove the rubber ash tray inserts and rubber mat from the console.
  3. Remove the floor shift control knob. Refer to Floor Shift Control Knob Replacement.
  4. Remove the center console shift lever bezel, Buick only. Refer to Console Shift Lever Bezel Replacement (Refer To List 1).
  5. Remove the console storage compartment. Refer to Front Floor Console Compartment Replacement.
  6. Remove the center console retaining screws.
  7. Adjust the parking brake to the full-up, or fully engaged position.
  8. Release the 2 forward trim extensions ears attached to the lower instrument panel (I/P), Buick only.
  9. Slide the console rearward and raise the rear of the console in order to expose the electrical connectors.
  10. Disconnect the electrical connectors, as necessary.
  11. Adjust the parking brake to approximately the halfway position.
  12. Remove the center console from the vehicle.
  13. If replacing the floor console base, remove the following and retain for transfer:
    • 13.1.
      Remove the HVAC control module (if equipped).
    • 13.2.
      Remove the armrest.
    • 13.3.
      Remove the HVAC module and duct assembly.
    • 13.4.
      Remove the cupholder.
    • 13.5.
      Remove the HVAC upper duct.
or read the FSM (buy one) factory service manual, its all there every step and photos too, (all cars. are like that)
or
http://www.scantool.net/software/alldata-diy-1-month-subscription.html

log in, and see that. and more.

Feb 05, 2015 | 2006 Isuzu Ascender

2 Answers

How do you remove a rear cupholder tray in a 2003 Jeep Grand Cherokee?


Hello
In order to remove the rear passenger cup holder you must remove the console from the car and turn it over to gain access to the retainers that hold the cup holder into the console. If you go to the page at the web link below you will find detailed instructions with pictures (click on the pictures to enlarge them) on how to remove the console assembly from the floor.

http://www.wjjeeps.com/console.htm

Jun 06, 2011 | 2006 Jeep Grand Cherokee

1 Answer

How do you get into the battery compartment to change the battery?


The battery compartment is located right behind the center console in the G-class. To access it you will need to remove the cupholder assembly. It should have only 2 screws holding it down. Once you remove those screws and move the cupholder to the side you should be able to lift up the carpet so that you can remove the battery cover. If you have any problems let me know and I will try to help in anyway I can.

Jan 25, 2011 | 2007 Mercedes-Benz G500

1 Answer

Need to remove heater A/C dash control , what is proper procedure?


Look at fig. 4 for the heater a/c dash control: HEATER CORE Altima REMOVAL AND INSTALLATION
  1. Position the steering wheel in the straight-ahead position.
  2. Turn the ignition switch OFF.
  3. Disconnect the negative (() battery cable; then, the positive (+) battery cable. NOTE: Wait for a least 3 minutes after disconnecting the battery cables for the charge in the air bag circuit to dissipate before working on the air bag module(s).
  4. Remove the driver's side SRS and steering wheel by removing or disconnecting the following:
    • Lower lid from the steering wheel and disconnect the driver's air bag module connector
    • Left and right side lids from the steering wheel
    • Special bolts from both side of the steering wheel using a tamper resistant Torx wrench (T50)
    • Air bag module and store it face up
    • Horn's electrical connector and remove the steering wheel nut
    • Steering wheel from the steering column using a suitable puller
  5. Remove the passenger's side SRS by removing or disconnecting the following:
    • Glove box door and the glove box
    • Front passenger's air bag module connector
    • 2 special bolts using a tamper resistant Torx wrench (T50)
    • 4 passenger's air bag-to-instrument panel nuts
    • Front passenger's air bag module and store it face up.
  6. Drain the cooling system into a clean container for reuse.
  7. Discharge and recover the air conditioning system refrigerant.
  8. Working in the engine compartment, disconnect the heater hoses from the heater core tubes.
  9. Remove the instrument panel by removing or disconnecting the following:
    • Kick plate and dash side finisher on the driver's side
    • 2 lower panel-to-instrument panel screws and the lower panel on the driver's side
    • 2 lower reinforcement panel-to-instrument panel screws and the lower reinforcement panel
    • 6 steering column cover screws, the covers, the spiral cable and combination switch
    • 2 cluster lid "A" screws and the cluster lid "A"
    • 3 combination meter screws, disconnect the electrical harness connector and remove the combination meter
    • Switch panel
    • Instrument panel lower covers
    • Snap out the transmission shifter finisher (boot)
    • 4 cluster lid "C" screws and the cluster lid "C"
    • 4 audio and deck pocket-to-instrument panel screws and the audio and deck pocket
    • 5 center console screws and the center console
    • 2 center instrument panel screws and the center panel
    • front defroster grilles
    • Front pillar garnish
    • Instrument panel 3 nuts/4 screws and the instrument panel
    • 8 instrument stay assembly nuts and the stay
    • Steering member assembly 5 nuts/1 bolt and the steering member
  10. Remove the air conditioning housing assembly by removing or disconnecting the following:
    • Refrigerant lines from the air conditioning housing assembly
    • Thermo control amp
    • Air conditioning housing assembly
  11. Remove or disconnect the following:
    • Heater unit
    • Heater core from the heater unit Fig. 1: Exploded view of the steering wheel and air bag module 93112gd9.gif
      Fig. 2: Exploded view of the passenger's side air bag module 93112gd0.gif
      Fig. 3: Exploded view of the instrument panel assembly 93112ge1.gif
      Fig. 4: Exploded view of the heater housing assembly and related components 93112ge2.gif
      Fig. 5: View of the heater core and heater housing 93112ge3.gif
    To install:
  12. Install or connect the following:
    • Heater core to the heater unit
    • Heater unit
  13. Install the air conditioning housing assembly by installing or connecting the following:
    • Air conditioning housing assembly
    • Thermo control amp
    • Refrigerant lines to the air conditioning housing assembly
  14. Install the instrument panel by installing or connecting the following:
    • Steering member assembly and the steering member 5 nuts/1 bolt
    • Instrument stay assembly and the 8 stay nuts
    • Instrument panel and the instrument panel 3 nuts/4 screws
    • Front pillar garnish
    • Front defroster grilles
    • Center instrument panel and the 2 center panel screws
    • Center console and the 5 center console screws
    • Audio and deck pocket and the 4 audio and deck pocket-to-instrument panel screws
    • Cluster lid "C" and the 4 cluster lid "C" screws
    • Snap in the transmission shifter finisher (boot)
    • Instrument panel lower covers
    • Switch panel
    • Combination meter, connect the electrical harness connector and install the 3 combination meter screws
    • Cluster lid "A" and the 2 cluster lid "A" screw
    • Combination switch, the spiral cable, the covers and the 6 steering column cover screws
    • Lower reinforcement panel and the 2 lower reinforcement panel-to-instrument panel screws
    • Lower panel and the 2 lower panel-to-instrument panel screws, on the driver's side
    • Kick plate and dash side finisher, on the driver's side
  15. Working in the engine compartment, connect the heater hoses to the heater core tubes.
  16. Install the passenger's side SRS by installing or connecting the following:
    • Front passenger's air bag module
    • 4 passenger's air bag-to-instrument panel nuts
    • 2 new special bolts and torque using a tamper resistant Torx wrench (T50) to 11-18 ft. lbs. (15-25 Nm)
    • Front passenger's air bag module connector
    • Glove box door and the glove box
  17. Install the driver's side SRS and steering wheel by installing or connecting the following:
    • Steering wheel to the steering column
    • Steering wheel nut and torque the nut to 22-29 ft. lbs.
    • Horn's electrical connector
    • Air bag module
    • New special bolts to both sides of the steering wheel and torque the bolts using a tamper resistant Torx wrench (T50) to 11-18 ft. lbs. (15-25 Nm).
    • Both the left and right side lids to the steering wheel
    • Lower lid to the steering wheel and connect the driver's air bag module connector
  18. Refill the cooling system.
  19. Connect the positive (+) battery cable; then, the negative (() battery cable.
  20. Evacuate, charge and leak test the air conditioning system refrigerant.
  21. Operate the engine to normal operating temperatures; then, check the climate control operation and check for leaks.

Nov 19, 2010 | 2002 Nissan Sentra

1 Answer

Replacing console light for shifter selection in 2002 Ford Escort ZX2


you have to remove the console from the car to get to the light. There are two retainers on either side of the console at the very front. push those in and the front will release. then you have to unscrew the rear of the console. two screws are located just below the rear cupholder on either side. the rear console should easily slide back and up. there are two screws exposed on the front console just in front of the emergency brake handle. remove those and you can remove the console. the gearshift lever must be in drive to clear the console. remove the screws holding the shift plate in place and the bulb is exposed

Jan 23, 2010 | 2002 Ford ZX2

1 Answer

Install a cd player in hyundai accent 2000


You have to remove the glove box, behind the glove box are some heater control cables that need to be unhooked, and also on drivers side by gas pedal there are 2 cables that need unhooked(the things they are hooked to, one is yellow and one is white). then there are two screws behind the slide out cupholder(hold cupholder halfway out to see them), then carefully pry the center console out starting at the bottom and working your way up. unplug all the plugs in the back and voila! you can unbolt the radio.

Jan 09, 2010 | 2000 Hyundai Accent

1 Answer

How do you remove the cupholder?


For the indash center cupholder, you need to remove that odd-shaped panel directly below it on the lower dash. There is 2 screws you can remove from there and then there are 2 more on the sides of the cup holder you can see from the front when the holder is in the open position... be patient and wiggle it around a little it will come out of there!

Let me know how you do..

Mar 31, 2009 | 1999 Ford F350 Regular Cab

1 Answer

How do you remove or replace the passenger airbag on a 99 contour , Is it a whole dash unit? What holds the drivers bag in the steering wheel? I assumed it was a tork but not sure. Where is the control...


Please rate as fixya if this helps.
the air bag control module is under the console.

  1. Disconnect the battery ground cable.
    1. Wait one minute.
  2. Remove the center console. For additional information, refer to Section 501-12 .
-----------------------------------------------------------------
  1. Disconnect the battery ground cable.
  2. Wait one minute.
  3. NOTE: Contour shown, SVT similar.
    Remove the rear floor console screws.
    1. Move seat fully forward.
  1. Fully apply the parking brake.
  1. Detach the shift indicator selector bezel.
  1. Detach the shift bezel from the selector housing.
    1. Remove three bolts.
    1. Detach shift bezel from the console.
  1. NOTE: The rear floor console must be raised to disengage the front retaining clips.
    Raise and remove the rear floor console.
  1. Remove the four front floor console retaining screws.
  1. Detach the front floor console.
    1. Set the gearshift lever into position 1.
      Partially remove the front floor console.
  1. Disconnect the cigar lighter electrical connections and remove the front center console
-----------------------------------------------------------
  1. Disconnect the air bag control module electrical connectors.
    1. Depress the locking tang.
    1. Slide the locking bar back.
    • Disconnect the connector.
  1. NOTE: The air bag control control module is grounded by the retaining bolts.
    Remove the air bag control module.
    • Remove the three bolts.
--------------------------------------------------------------------------------------------
driver air bag module

  1. Disconnect the battery cables.
  1. Rotate the steering wheel 90 degrees to access and remove the Torx screw. Rotate the steering wheel 180 degrees to access and remove the Torx screws.
  1. Remove the driver air bag module.
    • Disconnect the electrical connector.
    • Remove the air bag module.
------------------------------------------------------------------------------------------
  1. Disconnect the battery cables. For additional information, refer to Section 414-01 .
  1. Open the glove compartment, press the sides inward and lower the glove compartment to the floor.
  1. Remove the passenger air vent duct.
    1. Disconnect the duct from the heater box housing.
    1. Disconnect the duct from the instrument panel register and remove.
29e093f.gif
  1. Disconnect the passenger air bag module electrical connector.
  1. Remove the two retaining bolts securing the rear of the passenger air bag module to the cross-vehicle beam.
14df419.gif
  1. sxp~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Support the passenger air bag module when removing the retaining nuts.
    Remove the two nuts from the front of the passenger air bag module.
4a697c8.gif
  1. Remove the passenger air bag module.
    • Lower the front edge of the passenger air bag module, roll the passenger air bag module around the cross-vehicle beam lowering it into the passenger footwell.
82a0ae0.gif

Mar 15, 2009 | 1999 Ford Contour

1 Answer

How to remove cupholder console on 2003 Explorer


did you try just sticking meter probe or test light probe in the hole,dead center at back for indication of power to it? Careful not to touch sides if using test light, you will blow a fuse. Steady hand.

Jan 04, 2009 | 2003 Ford Explorer

1 Answer

How to remove front door panel on volvo s60 t5 2002 driver side


Pop the grab handle cover off, two different styles.

1. With a slot under the grab handle, take a small screw driver off and gently push up, it should just pop out.

2. Simple cover that can be separated with a bone tool or similar so you don't chip the cover piece.

Behind that you will find two Torx 25 screws, Take those out.

Around the edge of the panel should be around 8 plastic rivet type of thing.

Again...two different styles.

1. With center pins that blend in perfectly with the rivet. Should be about 3/32nds diameter. Push the center in and the rivet deals should pop out. Be sure not to lose the center piece...easy to lose.

2. Same deal but with a larger center pin.

Take the plastic triangle piece near the upper right hand area as facing the panel.

Pull bottom away from door and up to release from top section of door.

Careful removing the cable for the door lock release, and remove the connectors from the tweeter and driver's door module.

Aug 12, 2008 | 2005 Volvo S60

Not finding what you are looking for?
2005 Volvo S60 Logo

Related Topics:

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7689 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...