Question about 1995 Honda Accord

1 Answer

Brake pedal loosing pressure it works fine then slowly goes to the floor

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 8,531 Answers

If there are no leaks at any of the wheels, suspect your master cylinder has failed.

Posted on Sep 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My brake pedal slowly losing pressure goes to the floor and then I have to pump it up again


If you break fluid level is correct and your break pedal goes down to the floor means that your master cylinder is going bad and you might loose your breaks completely if not checked or replaced. Your breaking system is down to the last O ring inside the master cylinder, once that rubber O rings goes you will not have any breaks at all. Master cylinders have a number of rubber O rings that work like a plunger or piston that produce pressure within the breaking system. When the first one wears down due to age, your pedal begins to loose break pressure and you have to pump your breaks several times to gain breaking. You are now down to the last rubber O ring and a warning that your master cylinder needs to be checked. You can still use your breaks but only for a few days before the other rubber O ring gives out too. Once both O rings give out you completely loose your breaks.

Apr 12, 2015 | Cars & Trucks

1 Answer

Brake pedal goes to floor when engine running but is fine when engine off


bleed the brakes again starting at the longest line at the rear and work forward . The indication is still air in the lines.

Feb 05, 2015 | 2002 Saturn SC

2 Answers

Why do i have loss of brake pressure


Long shot: Bad master cylinder - Typically the brake pedal will slowly sink to the floor. On early 2000 vintage Chrysler products you need to check brake lines as they have been known to rust (and fail catastrophically)

Jul 04, 2014 | 2003 Jeep Wrangler

2 Answers

I have replaced my brake pads I've bleed my lines several times. The brakes work fine until I hold the brake pedal down, thats when it slowly goes down to the floor in a few seconds and the brak


sounds like the brake master cylinder seals are worn buy a master cylinder kit and get a mechanic to repair it it is a lot cheaper than replacing the whole unit

Feb 27, 2013 | 1995 Honda Passport

1 Answer

Brake pedel fades


Chances are you have a small pin sized hole in your brake lines were your fluid id slowly leaking loosing brake pressure. I would fill the master cyl. full then have a friend look under your car while u step on the peddle to see if u can see any brake fluid leaking anywere. If there is none i would try bleeding the brakes. There could be air in your brake lines also causing this to happen.

Nov 17, 2011 | Dodge Sprinter

1 Answer

1992 F250 460 cid automatic 2w drive 85000 mi. Just replaced my master cylinder, all 4 brakes, and both front rotors. Afterward I blead the brakes and got bubbles out of fluid. Problem is : when not...


There is never a test or reason to pump your brakes

Accomplishes absolutely nothing.

There is no pressure in a braking system at all,
until you SLOWLY apply the brake pedal.

Then less than 1" off movement in the master cyl,
will develop 600 to 1800 lbs at the wheels

Release the brake pedal, the system goes to zero,
IT DOES NOT HOLD ANY PRESSURE

To answer your question

You not suppost to press the pedal hard
The saying goes--you apply the brakes,
not force the pedal arm and pin into the
vacuum booster, as though you want to damage it

When your driving what happens ?
You have higher manifold vacuum and
thus your pedal is normal,why the VACUUM
brake booster

Mar 31, 2011 | 1992 Ford F250

4 Answers

2005 Equinox Brake Problems


My 03 trailblazer does the same thing and the service dept. told me that it was normal for this model to do that, it has never failed to stop but if your sitting at a red light you can feel the peddle go down to almost the floor but it stops fine and it has done this since day 1 and they say thats normal on the trailblazer.

May 15, 2008 | 2003 Chevrolet Equinox

Not finding what you are looking for?
1995 Honda Accord Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...