Question about 1994 Toyota Pickup

1 Answer

What do I loosen to get 1st belt off so I can change ac belt?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Toyota Expert
  • 178 Answers

Assuming you're talking about the 22re ... there are tensioners on both the power steering (first) and the a/c belts. Loosen the bolt on the pulley and then the bolt on the side of the tensioner tightens and loosens the belt. You might want to check the inner ... alternator / water pump belt while you're there. No tensioner for this one, you need to loosen the bolt that the alternator pivots on, loosen the bolt on top of the alternator that holds it in place on that bracket and then pry alternator and tighten bolts to hold the tension.

Posted on Sep 06, 2010

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
morse008
  • 1111 Answers

SOURCE: How do I loosen the bet that goes to the ac,power

loosen the bolt to the alternator itself all 3 to be exact then it will allow you to access the removal of the belt

Posted on Sep 06, 2009

BCAS1298
  • 3092 Answers

SOURCE: i want to change belt on ac it it nessary to have

Yes, that's what lock's it in place to hold tension on belt, loosen nut on pulley, and turn other bolt and pulley will slide up or down to release tension on belt.

Posted on Jul 09, 2010

duane_wong
  • 6826 Answers

SOURCE: cant figure out how to loosen AC belt, goes around

OK,

I would first determine where the bolts are for the ac compressor and loosen them until the belt slides off.

Or, I know this may sound goofy, but you can get a breaker bar and socket or a large wrench and turn the crankshaft while putting a large flat screwdriver in between the v-belt and one side of the v of the pulley, and TURRRRRN it slowly until the screwdriver wedged in there actually takes the belt off (with turning).

That's a trick to use, but inspect the belt for damage afterward, or replace the belt if it is damaged in the process, which it usually is not.

Hope that helps.

Posted on Jul 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing of ac belt


usually to change the serpentine belt all you will need to do is loosen the belt tensioner and take the belt off the pulleys. here is a video that might help you. the serpentine belt drives the ac.

Jul 24, 2015 | AC Cars & Trucks

1 Answer

Show me how to change ac pelt


loosen the belt tension adjuster jam nut on side and loosen the lockscrew to loosen release tension to the AC COMPRESSOR belt.your vechicle has two tension adjusters one for power steering and tension adjuster for AC COMPRESSOR AND ALTERNATOR.

Sep 01, 2012 | 2002 Kia Sedona

1 Answer

How to change ac belt


you have to loosen the drive belt adjuster jam side nut and loosen the adjuster bolt,that will loose tension so you can remove drive belt to AC COMPRESSOR.

Sep 01, 2012 | 2002 Kia Sedona

1 Answer

How to change belts on 2002 Nissan Frontier 4 cylinder


2002 frontier 4 cyl: 1) take off air intake tube, 2 screws 13 mm above radiator. 2) 1st belt for power stirring has pulley, undo pulley screw and unscrew adjuster bolt enough to take belt off 3) 2nd belt for alternator and water pump has no pulley but adjusting bolt and mounting bolt on alternator pulley, loosen mounting bolt and unscrew adjusting bolt enough to take belt off, if alternator will not move go under the truck and remove plastic cover- 6 screws 13 mm heads, after that look directly under alt. Pulley and should see a screw head 9/16 in, loosen it so alternator can move, now should be easy to remove belt ( it will be a lot harder to put new one though) 4) 3rd belt for compressor has pulley so follow #2 to remove it ,have to be done under the truck. First 2 belts will have to work around fan blades to remove them so wear gloves. After replacing belts remember that not to over tighten bolt on pulleys.

Jul 05, 2012 | 2002 Nissan Frontier Crew Cab

1 Answer

I am trying to change my 2001 Mitsubishi Mirage (w/ ac) alternator belt. I loosened the tensioner, took out the top - bottom and inside bolt of the ac compressor to take off the first belt and even took...


BEFORE ADJUSTING THE ALTERNATOR BELT DISCONNECT THE NEGATIVE BATTERY CABLE OR YOU MIGHT BLOW AN EXPENSIVE HIDDEN FUSE.
I would replace the steering pump belt at the same time you do the alternator belt (buy both).
To take off the alternator belt .
First , take off the negative battery cable so you do not blow an expensive fuse on the positive battery cable clamp(or a block fuse under the hood). Facing the back of the automobile , reach UNDER the alternator and loosen the bolt on the bottom right side, now loosen the bolt on the adjuster block on top, you can now turn the adjuster bolt and move the alternator to change the belt.
To take off the steering pump belt on the front of the motor, you need to loosen the nut on the back side of the pulley (right side of pump mount), the nut holds the adjuster pulley in place . With the adjuster pulley nut loose , you can use the adjuster bolt to move the pulley to adjust/take off the steering pump belt.

Jun 04, 2011 | 2001 Mitsubishi Mirage

2 Answers

How do you change alternator belt on 1997 mazada 626


heres a diagram to help you, loosen the bottom bolt a few turns then loosen the top bolt then loosen adjusting bolt to loosen belt, use the adjuster to tighten the new belt then tighten top and bottom bolts, hope this helps,8a841eb.gif

Oct 04, 2010 | 1997 Mazda 626

2 Answers

How do you remove/replace the AC belt? There are a lot how to's for serpentine replacement but none that tell you how to remove the AC belt which has to come off first.


loosen the center bolt of the a/c idle pulley, then on top of pulley you will see the adjusting bolt, turn to loosen to remove belt, after new belt , tighten to where you have 1/2 play on elt then tighten center nut of pulley

Feb 04, 2010 | 2000 Dodge Caravan

1 Answer

How do I loosen the bet that goes to the ac,power


loosen the bolt to the alternator itself all 3 to be exact then it will allow you to access the removal of the belt

Aug 12, 2009 | 2004 Dodge Stratus

1 Answer

How to change 1999 nussan quest ac belt


http://groups.yahoo.com/group/villagerquest/

Belt —A/C Removal
  1. Remove the A/C compressor drive belt.
    1. Loosen the A/C compressor drive belt pulley tensioner bolt.
    1. Loosen the A/C compressor drive belt idler pulley adjustment bolt.
40f6b66.gifInstallation
  1. sxv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Incorrect drive belt installation will cause drive belt failure.
    NOTE: Inspect the pulleys for warping or abnormal wear.
    NOTE: Make sure drive belt is properly installed on each pulley.
    To install, reverse the removal procedure.
    • Adjust the A/C compressor drive belt. For additional information, refer to Belt Adjustment—A/C .

Aug 10, 2009 | 1995 Nissan Quest

2 Answers

BELT TOO LOOSE ON 1990 FORD 5.0 BELT FOR AC & AIR PUMP.


the idle pulley is difficult to adjust on this one i will try to walk you through large bolt on front of pulley loosen about two turn the behind the bracket in which it is mounted there is a 15mm adjusting bolt tighten to tension loosen to loosen i say this because some are backwards lol tighten untill you push down on the belt and it deflects only about 1/4 in retighten the front

Jun 11, 2008 | 1990 Ford LTD Crown Victoria

Not finding what you are looking for?
1994 Toyota Pickup Logo

304 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8547 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...