Question about 2006 Ford Explorer

1 Answer

Trying to find location of the OBD II on an 2006 Ford Explorer

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 4,369 Answers

Should be in the car under dash on dirver side. 16 pin connector. Auto Zone will run scan for free.

Posted on Sep 05, 2010

  • gerry bissi Sep 07, 2010

    Here's waht an OBD II diagnostic connector looks like.




×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ive got a 93 ford ranger.after it gets warm & u cut it off for about 5 mins,& start it back its like it floods


Ford Check Engine light Codes - FreeAutoMechanic

www.freeautomechanic.com/diagnostictroblecodes7.html
Full list of OBD I Diagnostic Trouble Codes for your Ford Vehicle. If your Check engine light is on you may have a serious problem. Scan your codes and follow ...

EEC-IV 2 and 3 digit trouble codes. - Ford Explorer and Ranger ...

www.explorerforum.com > ... > EEC IV
Feb 6, 2007 - Serious Explorations Ford Explorer and Ranger Message Board .... 3.8L AXOD - Message center data link circuit fault - See code 70 73 (O) Is FORD DEALER the only place who can read out ABS error ...
Dec 5, 2011
Error codes 186 & 539.
Aug 15, 2009
OBD-II Diagnostic Trouble Codes (DTCs)
Nov 8, 2008
Have a Code? OBD II Trouble Codes Here
Jan 19, 2006
More results from www.explorerforum.com

EEC-IV Diagnostic Trouble Codes - Diagnose problems in


Dec 19, 2015 | 1988 Ford Ranger

3 Answers

Where do you plug in a actron obd scanner ?


The connector is located on the drivers side just above the parking brake pedal.

Hope this helps.

Zeppelinx12

Mar 05, 2011 | 1994 Ford Explorer Limited

2 Answers

I need to disable DRL in Ford Explorer 2006


Go underneath the hood and find the DRL module in the Fuse Box and just pull it out.

May 28, 2010 | 2006 Ford Explorer

1 Answer

2000 explorer 4x4 4.0L SOHC - I have no power to


check fuse number 5 in the passenger compartment fuse box, it is a 10 amp, that is the OBD connector power supply, if that fuse is good just run power to pin number 16 of the connector, this the bottom row of pins last one on the right.

Mar 02, 2010 | 2000 Ford Explorer

1 Answer

Failed emissions What fuse for OBD port on 2006 Ford Fusion?


check the out put from the computer to the obd ll port if good need to check the wiring harness ,connections and pin contacts from computer to obd ll port connections possible short,frayed or broken wire

Feb 14, 2010 | 2006 Ford Fusion

1 Answer

Check engine light 97 ford explorer. obd-II po141 bank 1 sensor 2. need to locate sensor


Looked up your OBD II code for your Explorer and got the following: Bank 1 Sensor 1
The possible causes are listed below per Chilton: *same result for all engines available on your vehicle

Trouble Code: P0141 (4.0L V6 VIN E Auto)
HO2S-11 Heater Circuit (Bank 1, Sensor 1) Print this code dataprint_icon_codes.gif
Number of Trips to Set Code: 2
OBD II Monitor Type: CCM Details
Indicators: MIL Details
Trouble Code Conditions:
During testing the heated oxygen sensor (HO2S) heaters are checked for open and short circuits and excessive current draw. The test fails when the current draw exceeds a calibrated limit or an open or short circuit is detected.
Possible Causes:
  • Vacuum hose disconnected on exhaust gas recirculation (EGR) system module (ESM) applications* Short to VPWR in the harness or HO2S
  • Water in the harness connector
  • Open VPWR circuit
  • Open GND circuit
  • Low battery voltage
  • Corrosion or incorrec
The sensors themselves appear in the illustration linked to below. The illustration is for the Ford Ranger but indications are that other models have similar locations. Hope this helps with your problem. Best of luck!
Greg

http://www.chiltonlibrary.com/content/images/8968/images/89684g23.pdf

May 17, 2009 | 1997 Ford Explorer AWD

Not finding what you are looking for?
2006 Ford Explorer Logo

452 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...