Question about 1999 Ford Crown Victoria
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: bad coil pack on crown vic
well if you have checked the spark plugs and they look good then its probly the coil If the plugs have never been replaced i would start with a tune up and see if this fixes the problem. If not there is no good way for you to test it you would need a computer to hook up to the car
Posted on Jan 24, 2009
You can purchase the wiring diagram for $5.99 from the following site: http://www.wiring-diagram.com/. You can also purchase a wiring diagram book from the following link: http://cgi.ebay.com/ebaymotors/2008-FORD-CROWN-VICTORIA-MARQUIS-WIRING-DIAGRAM-MANUAL_W0QQitemZ120394723100QQcmdZViewItemQQimsxZ20090320?IMSfp=TL090320147007r15080.
Hope this helps,
Posted on Mar 23, 2009
1987 Ford Crown Victoria 5.0L FI 8cyl
Duraspark Type Plug Wires
The spark plug wires used with the Duraspark type ignition system are 5 / 16 in. (8mm) in diameter to contain the higher output voltage. There are two types of wires used in this system, and some engines may have both types installed. It is important to properly identify the type of wire used for each cylinder before replacements are made.
Both types are blue in color and have silicone jacketing. The insulation material underneath the jacketing on some plug wires is a silicone layer separated by glass braid. The plug cable not incorporating the silicone layer is used where engine temperatures are cooler and are identified with the letter SE with black printing. The plug cables with the silicone insulation are used where high engine temperatures are present. These cables are identified with the letters SS with white printing.
Each spark plug cable, if original, is marked with the cylinder number, model year and date of cable manufacture (quarter and year). Service replacement wires will not have cylinder numbers, or manufacture date.
On any vehicle equipped with a catalytic converter, never allow the engine to run for more than 30 seconds with a spark plug wire disconnected. Unburned fuel in the cylinder may ignite in the converter as it is exhausted and damage the converter.
When removing spark plug wires, mark and tag the individual wires. Grasp, then slowly, twist the insulator back and forth on the spark plug to free the insulator. Do not pull on the wire directly as it may become separated from the connector inside the insulator. Special tools are available which can help ease plug wire removal, and prevent damage to a cable.
When installing a new set of spark plug wires, replace the wires one at a time so there will be no confusion. Start by replacing the longest wire first. Route the wire exactly the same as the original.
Fig. 1: 6 cylinder engine-240Firing Order: 1-5-3-6-2-4Distributor Rotation: Clockwise
Fig. 2: 8 cylinder engine-255, 302, 351, 400Firing Order: 1-5-4-2-6-3-7-8Distributor Rotation: Counterclockwise
Fig. 3: 8 cylinder engine-390, 427, 429, 460Firing Order: 1-3-7-2-6-5-4-8 DistributorRotation: Counterclockwise
Visit autozone.com (free register) for more details.
I hope helped (rememer rated this) Good luck.
Posted on Oct 15, 2009
Tips for a great answer:
Mar 11, 2015 | 1987 Ford Crown Victoria
Jan 15, 2013 | 1999 Ford Crown Victoria
Aug 24, 2011 | 1997 Ford Crown Victoria
Mar 10, 2010 | 1999 Ford Crown Victoria
Sep 02, 2009 | 2005 Ford Crown Victoria
Jan 11, 2009 | 1999 Ford Crown Victoria
75 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: