Question about 1998 Chrysler Concorde

Open Question

Mi 96 chrysler concord 3.5 have no fire in the 6 spark cable the coil conector,dont have voltage,i did change the computer,alternator,fuel pump,the starter working good,but cannot get the engine runing what next

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
motor1258
  • 6674 Answers

SOURCE: 2000 chrysler concorde no spark on #2 cylinder

If it ran good prior to spark plug replacement, then yes, I'd be looking real close at the plug wire to that particular spark plug. Perhaps it pulled apart inside boot upon removal. It may even be an indication that they are all getting weak, and time to think about a new set if it's originals.

Posted on Mar 22, 2009

Ad
  • 1 Answer

SOURCE: my 96 chrysler concorde 3.3 wont start.

Change spark plugs wires and coil pack.

Posted on Jun 28, 2009

ZJLimited
  • 17970 Answers

SOURCE: how to remove alternator from 1997 Chrysler

e
3.3L Engine

  1. Disconnect the battery negative - cable.
b9a39c6.jpg

Fig. Wiring and nut locations



  1. Disconnect the alternator field circuit plug.
  2. Remove the B+ terminal nut and wire.
  3. Loosen the adjusting T-bolt, but do not remove it.
  4. Loosen the pivot bolt, but do not remove it either.
  5. Remove the alternator drive belt.
  6. Remove the adjusting T-bolt, pivot bolt, and mounting bolt, be careful not to loose the spacer.
  7. Remove the alternator.
To install:
  1. Attach the alternator to the support bracket. Tighten all bracket and alternator (except for the wiring nuts) bolts to 40 ft. lbs. (54 Nm).
  2. Install the B+ terminal nut and wire and tighten to 75 inch lbs. (9 Nm).
  3. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  4. Connect the negative - battery cable.

3.5L Engine

  1. Disconnect the negative battery cable.
  2. Loosen the lower mounting bolt but do not remove it.
  3. Loosen the pivot bolt, but do not remove it.
3260271.jpg

  1. Loosen the belt adjusting bolt.
  2. Remove the alternator drive belt.
  3. Remove the bracket.
  4. Remove the lower mounting bolt and pivot bolt.
  5. Remove the alternator.
  6. Disconnect the alternator field circuit plug.
  7. Remove the B+ terminal nut and wire.
To install:
  1. Attach the alternator and bracket to the engine, then tighten the mounting bolts to 40 ft. lbs. (54 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Install and tighten the B+ terminal nut and wire to 75 inch lbs. (9 Nm) onto the new alternator.
  4. Connect the alternator field circuit plug.
  5. Connect the negative battery cable.
Hope helped with this (remember rated this help) Good luck.

Posted on Nov 03, 2009

  • 1 Answer

SOURCE: My 96 Chrysler Concorde turns but won't start. It

it is the cam shafy sensor

Posted on Jan 17, 2010

  • 834 Answers

SOURCE: firing order for 1996 chrysler concorde

Here is the firing order diagram, and it is the same for the 3.3 litre and the 3.5 litre engine.


28ced56.gif

Posted on May 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 CHRYSLER CONCORDE, 2.7 HAS NO IGN ENG HAS BEEN REBUILT. TIMING DOUBLE CK, CRANK AND CAM SENSORS REPLACED. POWER TO COILS CKD OK. FUEL INJECTORS WORKING PROPERLY, BUT STILL NO IGN SPARK. HELP!!!!


Check that the wiring harness to the coils is getting 12v, this will confirm if the pcm is sending a signal for the sparks to fire. Check the ignition coil is sending spark to the plugs with a spark plug tester.

Oct 14, 2013 | 2002 Chrysler Concorde

1 Answer

I have a 1995 chrysler concorde and it wont start it is getting fuel and is rolling over but getting no fire


Have you checked the computer for trouble codes ?
Are you getting voltage to the coil ?
Have you checked the ASD relay ?

Jul 29, 2012 | 1995 Chrysler Concorde

1 Answer

96 chrysler missing terrible


check compression, check fuel pressure, test coils

Mar 14, 2012 | 1996 Chrysler Concorde

2 Answers

1994 CONCORD NO POWER TO FUEL PUMP, NOT FIRING AND DOES TURNOVER, REPLACED CRANK SENSOR AND CAM SENSOR, TRIED DIFFERENT RELAY FOR FUEL PUMP-STILL WON'T START?


NO POWER TO FUEL PUMP......CHECK ALL IN LINE WIRING
NOT FIRING... START WITH COIL PACK, DIST CAP ETC...PLUGS/WIRES??????
"HOT WIRE" (DIRECT W/ FUSED JUMPER) TO FUEL .PUMP....NO - GO,,,BAD PUMP

Oct 09, 2011 | 1994 Chrysler Concorde

1 Answer

Firing Order diagram for 2006 Ford Explorer


Hope this helps. The ignition coil:
  • changes low-voltage pulses from the PCM to high-voltage pulses.
  • fires 2 spark plugs simultaneously.
  • has 3 transformers.
    • One transformer fires the spark plugs for cylinders 1 and 5
    • One transformer fires the spark plugs for cylinders 2 and 6
    • One transformer fires the spark plugs for cylinders 3 and 4
Spark plug wires:
  • carry high-voltage pulses from the ignition coil to the spark plugs.
The spark plugs:
  • change high-voltage pulses to spark at the gap, which ignites the fuel and air mixture.
The firing order is 1-4-2-5-3-6.

69efa96.jpg

Jun 06, 2010 | 2006 Ford Explorer

2 Answers

Chrysler wont start


I CHANGE CAM AND CRANK SENSOR,FUEL PUMP,COMPUTER BRAIN BOX AND COIL PACK STILL GETTING NO FIRE UNLESS I JUMP A FIRE WIRE FROM BATTERY

Jul 02, 2009 | 1994 Chrysler Concorde

1 Answer

2.7 l misfire after changing plugs


From karjunkie:

If the plugs get wet, then you have a spark problem somewhere in the ignition system. Pull a spark plug and hold it against a ground while you turn the engine over. You need to see a fat blue spark. If not, check the distributor, spark plug wires and coils. An easy way to test for spark is with an inexpensive spark tester. This is a device that is readily available at most auto supply stores. If the plugs do not fire properly, check the spark plug wires for fraying or cracking. Next, you need to check the coil(s). If firing voltage is low (weak spark), measure the coil primary and secondary resistance with an ohmmeter. If it is out of specifications, replace the coil. Also, make sure the coil is receiving normal voltage from the PCM or ignition module. If it is low, check the charging system for anything that may be reducing alternator output (battery and alternator cable connections, ground connections and voltage output).

Mar 22, 2009 | 2000 Chrysler Concorde

Not finding what you are looking for?
1998 Chrysler Concorde Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...