Question about 2005 Dodge Durango

Open Question

2005 DODGE DURANGO CRANK SENSOR LOCATION - 2005 Dodge Durango

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

techbuster
  • 5081 Answers

SOURCE: tips on replacing 1999 dodge durango crank sensor

The crankshaft position sensor is on the right side of the engine just to the rear of the right hand exhaust manifold, the sensor is attached to the block with two bolts, part of the sensor overhangs the transmission bell housing. Look at the bell housing and start going up, you will see the sensor almost inline with the right exhaust manifold. It has a gromment that overhangs the transmissions bell housing. Use a flashlight from below and you will see it,

Posted on Oct 07, 2009

66 chrgr
  • 1011 Answers

SOURCE: where is the crank sensor located on 2005 chrysler pt cruiser?

the crank sensor is located on back right side of engine by were the trans. bolts up.is the no start when could or hot?

Posted on Jan 25, 2009

awcforever
  • 359 Answers

SOURCE: Crank sensor location 1999 dodge durango

The crank sensor is on the front of the motor on the case of the timing gear. If you want to replace it, the sensor itself isn't the problem, but you have to actually reset your timing, and get it recalibrated. If the timing isn't set, you can possibly damage your engine. But as far as location, it should be fairly easy to find. Hope all works out.

Posted on Feb 22, 2009

  • 193 Answers

SOURCE: Dodge Durango 1998 5.2L Output Speed Sensor code P0720 Location

Its in different locations depending on if its 2wd or 4wd. For 2wd its in front of the drice shaft or for 4wd its in the tranfer case, just look for a white shape like box with wires plugged into it and you need a socket to remove it, iam not sure how much it is to replace as the cost varies at different shops.

Posted on Jun 19, 2009

  • 51 Answers

SOURCE: locating and replacing a camshaft sensor in a 2005 dodge neon

this is a very very simple procedure. you do not need pics. there is a sensor located at the end of the engine on the far side from the belts. at the top. it has a plug with two wires in it. just remove the two 10mm bolts un hook the plug and reverse the process to reinstall. if you have a factory intake you may have to remove it to access this sensor. just the intake tube.

Posted on Aug 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is a coil and where is it located in a 2005 Dodge Durango?


I believe each spark plug has it's own coil.

coils take 12V and cranks them up to thousands of volts

Dec 17, 2015 | 2005 Dodge Durango

1 Answer

Where is the o2 sensor bank sensor 2 located on a 2005 dodge durango 4.7 engine I get an error code of P0038


P0038 HO2S Heater Control Circuit High (Bank 1 Sensor 2) It is located behind the catalytic converter, in the exhaust pipe . P0038 HO2S Heater Control Circuit High Bank 1 Sensor 2

Nov 01, 2015 | 2005 Dodge Durango

1 Answer

How do I locate the Crank shaft sensor on a 2005 Dodge Durango


Have you looked on the transmission just behind the engine block? A lot of the Dodge vehicles get readings of the flexplate/flywheel.

Sep 12, 2014 | 2005 Dodge Durango

1 Answer

Trying to find the crank sensor on a dodge durango 1999


To get exact procedure , please click on the link below and follow the procedure:--- http://technoanswers.blogspot.com/2011/06/where-is-crank-sensor-located-on-dodge.html ------------ This should help.Thanks.Helpmech.

Jun 02, 2011 | 1999 Dodge Durango

1 Answer

WHERE IS THE IAT SENSOR ON A 2005 DODGE DURANGO LOCATED AT?


The sensor is located either in the air filter box or in the air duct coming from the box going to the throttle body. Let me know if you need anything else.

May 07, 2010 | 2005 Dodge Durango

2 Answers

Crank sensor location for 2002 durango 5.9


should be on the drivers side back of motor stuck in the tranny bellhousing at the top held in by either a 10mm bolt or a 12 mm

Jan 21, 2010 | 2002 Dodge Durango

1 Answer

Crank shaft sensor. where is it located on a


behind the engine on the top passenger side of the engine. 2 13mm. bolts.goes through the bell housing.

Mar 29, 2009 | 2000 Dodge Durango

4 Answers

Crank sensor location 1999 dodge durango


the crank sensor is located passenger side back of the engine were the trans and engine come together .there are 2 - 13mm.bolts that bolt to top of the engine.

Feb 22, 2009 | 1999 Dodge Durango

1 Answer

Where is the crank sensor located?


The sensor is bolted to the top of the cylinder block near the rear of right cylinder head
The sensor is accessed by removing the right front fender liner
  1. Remove right front tire and right front wheelhouse liner.
  2. Disconnect crankshaft position sensor pigtail harness from main wiring harness.
  3. Remove two sensor (recessed hex head) mounting bolts
  4. Remove sensor from engine.

Jan 08, 2009 | 1999 Dodge Durango

Not finding what you are looking for?
2005 Dodge Durango Logo

Related Topics:

861 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...