Question about 1996 Buick Skylark

1 Answer

Fuse panel inside car.. turn,cruse,alarm,airbag,and pcm fuses have 0 volts......fuse panel at Batt fuse panel has. pcm fuses o volts...also ing only two of these small fuses are hot.....was running fine any ideas

Posted by on

  • leinkdesigns Sep 05, 2010




1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Master
  • 373 Answers

Check neg battery cable

Posted on Sep 05, 2010

  • leinkdesigns Sep 05, 2010

    if that was true no fuses would be hot.

  • Rick Wrieden
    Rick Wrieden Sep 05, 2010

    only the ecm fuse and fuel pump fuse will keep it from running



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Is there 12 volt I can tap into to fit alarm

12 volt taps are everywhere. One of the easiest places to tap off 12 volts is in the electrical fuse box. Whichever fuse you decide to use, make sure it is a non-critical fuse like the ECM or fuel pump. When you look at the fuse panel, test which side of the fuse has voltage when the vehicle is turned OFF. You don't want an alarm system that only works when the vehicle is turned on!

Nov 28, 2017 | Cars & Trucks

1 Answer

Fuse for 2002 yukon dash board

There are a four fuse's that supply B+ voltage to the instrument cluster . Three are in the left instrument panel fuse box and one is in the under hood fuse box .ING 1 fuse 10amp , ING 0 fuse 10amp and CRUISE fuse 10amp . these fuse's are in the I/P fuse box. The last one is RADIO fuse 15amp located in the under hood fuse box . What kind of problem are you having ? A gauge not working or the whole instrument cluster not working ?

Jan 01, 2017 | Cars & Trucks

1 Answer

I have cadillac deville 2003 my battery reads good but my front fuse panel fuse number eight itpcm/batt keeps poopping car shuts off I am trying to figure out wat is ausing this need hel

This fuse has nothing to do with the battery .
PCM BATT Fuse 10A Powertrain Control Module (PCM), Theft Deterrent Module. That just means it's B+ voltage feed for the PCM an theft module . IT actually supply's B+ voltage too two different feed's for the PCM . Connector 1 terminals 20 & 21 . You have a dead short to ground on one of those feeds or your PCM or theft control module is shorted . If you don't know automotive electrical , I suggest very strongly you take to someone who is !

Oct 04, 2015 | Cadillac Cars & Trucks

1 Answer

98 chevy malibu my alt isnt charging new alt batt test good cut out the fuselink on starter the alt wire runs thru firewall If i run a wire straight to the batt it is putting out 19v any suggestions

Did you check the fuse in the under hood fuse box ? GEN / BATT fuse 10amp . Is your check engine light on ? This is a computer controlled charging system , it should have four wires connected to the alternator . 1 - the heavier wire on the back ,this comes fro the starter - the one with fusible link , you could have checked for battery voltage with voltmeter ! The three other wires in the connector are the orange one ,this comes from the GEN / BATT fuse an should have battery voltage ! The last two come from the PCM - engine computer . The gray wire is the turn on signal from the PCM an the Red wire is the control from PCM ! Charging System Wiring Diagram MOTOR Magazine Article MOTOR Information Systems

Aug 14, 2015 | Cars & Trucks

1 Answer

Where is the fuse for the brain on a 99 chevy malibu

there are three fuse's for the ( pcm ) powertrain control module ! engine brain ! two are in the under hood fuse/relay junction block.
it is marked pcm / batt. fuse.10 amp. the other is pcm / ign fuse 10 amp. and then there is one in the let hand instrument panel fuse box. open the driver door at the end of the dash pull off end panel, fuse box behind there. fuse is marked pcm / acc 10amp .

now what is the problem your having ? i can help !

Jan 21, 2015 | 1999 Chevrolet Malibu

1 Answer

What is the fuse number for driver cluster, temp, fuel, sensors, and radio on 2002 Pontiac Montanna

Do you know where the Instrument panel fuse block is ? Open the right front door, end of the I/P or dash. End panel comes off . just grab an pull. Fuses under panel and are marked on inside of panel. There are four fuses. Cluster /Batt 10 amp fuse , PCM/PASSKEY/ CLUSTER 10amp , IGN1 10amp , and MALL/CLUSTER 10amp fuse .

Jan 11, 2015 | 2002 Pontiac Montana

2 Answers

We just bought a 94 geo prizm a fuse was missing in ECU-IB slot when i put it in the air bag light went on and would not go out even with the car turned off. when I removed the fuse then the car would not...

The fuse was probably removed purposely due to an electrical short in either the air bag system or alarm system. Have it checked professionally. U will have a dangerous air bag on your hands if u leave it be. Speak to the seller 1st, if possible. Maybe they can compensate u.

Jul 24, 2017 | 1994 Geo Prizm

1 Answer


Open the hood and look for the engine compartment fuse block next to the driver's side firewall. Open the cover in order remove and inspect the fuse closest to the radiator labeled ING (Ignition) to see if the fuse connection is visibly broken or blown. If it is OK open the fuse panel located at the left end of the instrument panel inside the vehicle. To open, push the tab on the access door to the left and pull the door forward. Remove and inspect the two top right fused labeled IGN and PCM/IGN to see if the fuse connection is visibly broken or blown. Replace any defective fuses and try to start the vehicle. If it starts it could have been a bad connection or a more serious problem requiring service if the fuse keeps blowing. If it does not start it could be the ignition switch or starter.

Jul 27, 2010 | 1999 Chevrolet Cavalier

1 Answer

I have 1991 ford explorer 4.0 my battery light on my dash stays on when ing is off when i start the truck the batt. light goes off but when the ing is off lights on it kills the batt what s my problem

If you have tow package (factory) pull the fuse to trailer charge 30amp fuse. Under the hood fuse panel. It sould correct the problem. I corrodes in rear and backfeeds to Ignition.

Apr 09, 2010 | 1991 Ford Explorer

Not finding what you are looking for?
1996 Buick Skylark Logo

Related Topics:

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts


Level 3 Expert

80417 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides