Question about 2006 Pontiac Montana

1 Answer

Looking to replace the rt fron hub bearing in my 2002 montana van.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 373 Answers

I may be wrong it has to be preesed out and in

Posted on Sep 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace front hub assembly 2002 Suzuki XL7


the front wheel bearing hub?
XL-7 (the dash matters)
my wild guess, is the questions was
what are all steps to do this job. and tools.
that?
RTM?

https://suzukipitstopplus.com/Products/10056-2002-grand-vitara-xl-7-service-manual.aspx

http://www.fixkick.com/hubs/FW_BEARINGS.html#newer
the link shows all years, and variances.

here is a photo review, that is accurate up to
1998, and beyond , if you skip the bearing service parts. as yours are INTEGRATED
and NON-serviceable.
http://www.fixkick.com/hubs/FW_BEARINGS.html


the photo 6a and B
shows removing the hub,
so do that , buy a new hub and put it back
the same way, using the tool stated
at the stated ranges of torque
123-180 ft/lbs.
this range allows you to get the screws into the locking rings.

Dec 11, 2016 | 2002 Suzuki XL-7

1 Answer

Lost right front wheel while driving. no studs in hub. wheels very rusty. what caused studs to come out?


now you have to replace hub bearing to put wheel back.I pull out 95 chevy hub bearing still OK.

Feb 24, 2013 | 2003 Pontiac Montana

1 Answer

As the van is slowing down,i get a rubbing noise


Probably the front hub bearings, how many miles are on it? have they ever been changed?

Nov 23, 2010 | 2004 Pontiac Montana

1 Answer

Need to replace the front wheel bearings can i just replace them or dp i needto replace the hole hub?


The bearing comes pressed onto the hub. You can't get the bearing seperately.

Oct 30, 2010 | 2000 Pontiac Montana

1 Answer

How do you install a front wheel bearing on a 2001 Pont Montana


jack the vehicle up remove the wheel
remove the brake caliper bottom bolt 15mm. lift the caliper up and slide the caliper pin out
remove the caliper housing bracket 2 - 15mm. bolts
remove the brake rotor
remove the drive axle nut 1 5/16
the remove the hub bearing bolts 3- 13mm. they are in behind (best to use a 13mm flex socket)
disconnect the ABS harness
use a hammer and hit the hub bearing flage (it maybe corroded )
now the hub bearing is out clean the steering knuckle with sandpaper to remove corrosion
install the hub bearing (make sure the ABS harness is in the right position)
and reassemble
hope this helps

Apr 29, 2010 | 2001 Pontiac Montana

2 Answers

TURN RT APPLY BRAKES ABS/TRAC OFF COMES ON


bad front bearing/abs sensor The sensor is part of the bearing,or the wires are bad so that when you steer it open circuts and thinks the wheel is stopped. need to read codes or use a scan tool with live data to see which wheel the computer thinks is stopping. then look at that wheel for problems

Apr 25, 2009 | 2002 Pontiac Grand Prix

2 Answers

2003 Pontiac Montana Front Wheel Bearings


Remove the wheel, remove the hub nut, remove the brake caliper and rotor, put your socket and extension through the hub flange onto the bearing retainer bolts, undo them, release the abs sensor connector if it has it, remove the bearing and hub flange as an assembly, put the new one on and go backwards from here. Torque the hub nut to 180 ft/lbs, your done.

Apr 08, 2009 | 2003 Pontiac Montana

2 Answers

2002 Pontiac Montana


are u saying u replace the switch on the climate control
cause it would be the resitor on the blower causing it

Jun 09, 2008 | 2002 Pontiac Montana

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...