Question about 1991 Volvo 740

1 Answer

I need to put my timing belt back on and I don't know what the marks are and how to set them?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Volvo Master
  • 8,522 Answers
Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to set timing from scratch on 1993 Mercury Tracer 1.9L


On the pulley, they are marks that line up with a mark on the head. That is TDC for the cam. Then set the crank to 0 on the timing marks. Put the belt back on.

Nov 28, 2014 | Ford Cars & Trucks

2 Answers

Why doesn't My truck start after changing the Timing belt on My 1999 Ford Ranger?


you need to pull the timing back apart pull the number one spark plug and role the motor over by hand to top dead center on the compression stroke the the mark for the crank should be lined up or almost lined up line it up perfect on its mark then set the cam to its mark install belt role over by hand 2to4 full rotation marks should line up perfect . install crank pulley fire it up for a split second shut it off and put it all back together

May 25, 2014 | 1999 Ford Ranger SuperCab

1 Answer

1990 ford ranger 2.3 timing belt pully diagram


Set the crank to TDC using the timing marks, look for a mark on the cam pulley and a mark on the head, line those marks up and put on the belt

Feb 12, 2013 | Cars & Trucks

1 Answer

1991 Mazda Miata 1.6l timing belt broke.


You need to purchase a Haynes Manual or better. They are very common in your nearest chain part store. Like Autozone, Advance, Napa. More than likely you will have to set the crankshaft at TDC. "top dead center" and allign the two marks with the cam shaft! Watch when you put tension on the belt it will move the camshaft sprocket! And throw it back out of time.

Jul 13, 2012 | Cars & Trucks

1 Answer

Resetting timing after replacing head gasket


Do you have the timing belt on and the tensioner set correct? If so, just rotate the crankshaft around until the notch on the crank sprocket is lined up with the pointer on the oil puimp housing (TDC). Now the camshaft sprocket's notch or pointer should be at the top and exactly in line with the mark on the rear timing belt cover. If it's not correct, you'll have to release tension on the belt, remove it, and set the camshaft to the mark. But before you do that, turn the crankshaft back (counterclockwise) just three notches. Then you can turn the cam to line up, then return crank to line up, and continue with belt installation, setting the tension, and re-checking timing marks after rotating the crankshaft a couple of revolutions. Once you know the timing is set to TDC, no further timing adjustments are possible, because the computer controls timing. I don't know how important it is, but just to let you know: Chrysler recommends after belt removal or replacement that one perform the "crankshaft and camshaft relearn alignment procedure" using the DRB scan tool (Chrysler's scanner device) or equivalent scan tool.
And the firing order on all four cylinder engines is the same: 1 3 4 2.
I hope this helps you out. Cheers.

May 11, 2012 | 1996 Plymouth Breeze

1 Answer

I have a 1998 Dodge Stratus ES and am having problems getting the timeing belt on. Can somebody please explain how we may put the belt back on without a bunch of trouble?


Make sure your timing marks are lined up and start putting your belt on the rear cam first that would be 1,3,5 cam. Then route it under the water pump and up around the front cam 2,4,6 cam being careful the rear cam don't jump off it's mark. Keep tension on the belt while routing it. Continue routing it over the idler pulley keeping tension on it route it down and around the crank sprocket. Now set your tension pulley and replace the tension pin. Once the belt is set hand crank the engine 2 to 3 complete cycles then recheck your marks. This is for a 2.5 engine. Good luck hope this helps.

Jun 20, 2011 | 1998 Dodge Stratus

1 Answer

I have a Isuzu rodeo 1994 3.1 in I can't find the


The timing marks are stamped into the head and in the cam pulley, also on the crank and the case, find them and paint them white so you can see them, the new belts have the marks on the belt, they will line up, If they don't , you got it wrong, You can do this without spinning the cams or crank and losing the marks, as long as the belt marks line up, you will be all set. Put the pin in the tensioner before removing the belt. Did you change the water pump? And I think the engine is 3.2L. Get it in there and pull the pin, It should be right on. Turn over the engine by hand a couple times to make sure it comes around on the marks. If it is wrong, it will go about 11 or 12 miles, and you will need a new engine. Hope this helps.

Jun 04, 2011 | 1994 Isuzu Rodeo

1 Answer

I had to change my head gasket on my 2001 VW Passat. That went great but know when I try to put back my timing belt it will not start. I have tried everything. I have alligned all the marks and still...


After you aligned the timing marks and tightened up the tensioner pulley, did you re-check your timing marks? Usually when you tighten the tensioner it will pull the cam and crank out of alignment. Line up the crankshaft first and then check to see where your cam gear is. If it is not lined up, loosen the tensioner and move the cam gear ahead to line it back up. If it doesn't line up perfectly then go AHEAD until the marks line up and put the belt back on. If the gear is on the mark and the belt teeth don't line up, move the gear ahead until you can get the belt on,but no more than a full tooth on the belt. Tighten your tensioner and check again. At most the cam sprocket should only be off about 1/2 tooth from the marks and it should be ahead not behind. Re-align your distributor to #1 and it should start. Hope this helps.

Apr 11, 2011 | 2001 Volkswagen Passat

1 Answer

Which direction does the timing belt installs?


You know, I replaced alot of these and seen that on the directions. And yet they do not put a mark on the new belt. I have looked these things over and found know way to tell. So I just put them on. I have never had one come back. May I also recommend that since your already in there, that you replace all the timing components and the water pump too, if it's in there.You don' want to go back in a couple of months from now.

Nov 30, 2010 | 1991 Chrysler LeBaron

1 Answer

Need to time the engine ..trying to put new timing belt on it accidentally moved the top sprocket a bit and lost original timing not starting now...worked perfect before need to know how to put it


you will need to pull the distributor cap off and pull the #1 plug out and timing covers need to come off leave the harmonic balance on or take it off an put it on temporally so you can line up timing marks. with the #1 cylinder at top dead center and the rotor pointing to #1 plug put air into the cylinder to see if it holds compression if it does your in the right postion. Next trun the crank until the cylinder is at the top of the stroke power stroke, next make sure the harmonic balancer marks are lined up next look at the two timing gears I believe they are supposed to point towards each other if not move the one you think is wrong one tooth in the direction oppisite of the way it slipped if it is not lined up you will not have compression pull valve covers off so you can see the valves both the valves should be fully closed on the # 1 plug if it is your timing should be right if one is slightly open then tuen it till the #1 valve is closed and the gear marks line up then slide the belt back on once you are sure you have it set correctly put it all back together to set the timing with the light look at the hood and under the hood it will tell you how to set the timing and how many degrees they very from engine to engine where it was manufactured for and you need to follow the emmison sticker timing proceedure, if you need more information let me know.

May 29, 2009 | 1996 Ford Ranger SuperCab

Not finding what you are looking for?
1991 Volvo 740 Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...