Question about Chevrolet Blazer

1 Answer

Positive wires from battery, how many were do they go? I got this 1996 Blazer 4X4 LT with the engine out and all of the parts in boxes have it all back together but no power to the body. I have one running to the starter one to the alternator and one into the wiring harness. I should have one more to power the body?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 8,180 Answers

One should go to the fuse/relay box. Make sure you also have a ground wire between the engine and firewall/frame.

Posted on Sep 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blazer service engine soon light reset


If it is an early blazer, pre 1996 and has the OBD I system, you can reset the computer by removing the positive battery cable and touching it to metal or 10 seconds to ground the system. Then hook it back to the battery and if the light comes back on then you need to jump the "A" and "B" terminals to read the code. If your blazer is 1996 or newer then you will have the OBD II system and will need a scan tool to reset the light.

Aug 23, 2014 | Cars & Trucks

1 Answer

1996 dodge ram 1500 4x4 low voltige to transmission


If you only have 5 volts you may have a bad battery or alternator. Or maybe a B+ (battery positive) wire short to ground. Check voltage engine running at the battery then alternator +. If your voltage is that low your TCM won't work.

Jul 28, 2012 | 1996 Dodge Ram 1500 Club Cab

1 Answer

Will a '92 4.3 Vortec motor fit in a '96 4x4 Blazer?


Yes it will bolt up but NO it won't run . The 96 has a crank sensor hole in the timing cover the 92 does not . The timing covers are not interchangeable (different bolt pattern ) . You would have to change complete wiring harness including computer all the way to the OBD diagnostic port . It will work but a LOT of work .

Mar 27, 2017 | 1996 Chevrolet Blazer

1 Answer

Headlights intermittently turn on and off on a 1996 Chevy Blazer


I have a 95 blazer lt had same problem I went through complete wiring and found nothing took apart headlight switch found the copper diades corroded on entire switch I cleaned it with a small wire brush reistalled it and low and behold headlights work fine...

Nov 02, 2010 | 1996 Chevrolet Blazer

2 Answers

My 95 blazer 4x4 4.3 engine has a battery drainage problem when it sits all night,i had the charging system checked and it was ok.I tested all the fuse's with a tester with the key off,and more then half...


you would want to make sure everything is turned off in the truck and doors are shut. Take the positive battery cable off, connect a test light to the positive cable and the other to the battery, if there is a drain, the test light will light. Try pulling 1 fuse at a time til the test light goes out. Also have the battery tested to make sure it holds a charge.

Mar 07, 2010 | 1995 Chevrolet Blazer

3 Answers

Need wiring diagram of 1995 chevy blazer 4x4 with 4.3 vortex engine


need email address to send diagrams, need to know what parts of electrial you need

Feb 07, 2010 | 1995 Chevrolet Blazer

3 Answers

1991 Chevy S10 Blazer 4.3 4x4


4170636.jpgThis is all I've got.Hope this helps?

Dec 20, 2009 | 1991 Chevrolet S-10 Blazer

2 Answers

1996 chevy blazer won't engage in four wheel.


its the actuator on the front diff . this is a common problem and a easy but expensive fix

Mar 10, 2009 | 1996 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...