Question about 2001 GMC Jimmy

1 Answer

How do you remove the windshield wiper arm of a 2001 Jimmy GMC

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

It should be as simple as lifting the wiper arm off the window and underneath at the base there will be a secrew or a pin to lock it in place on the motor. Remove it and slide the arm off.

If this is helpful, I have created a group via facebook for people to help one another with automotive problems and to give advice about trouble shooting. Follow the link, http://www.facebook.com/group.php?gid=124082217647229

Posted on Oct 08, 2010

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
morganismo
  • 36 Answers

SOURCE: windshield wiper arm

These are a tight fit...Spray a little penetrating lubricant onto it and let it sit for about 20 minutes. You will notice there are splines that match up from the drive unit to the base of the wiper arm...sometimes these can get a little corroded and becasue of the relative surface area it makes them a real pain to get off. You may need to just pry against it gently with a flat head scredriver after you spray on the lubricant. Pray at it from all different sides of the base so that it doesn't bind up and get crooked.

Hope this helps! Good Luck!

Posted on Feb 12, 2009

  • 30 Answers

SOURCE: my wiper on my 2000 gmc jimmy went crazy. I cant

its part of combination switch need to remove steering column cover to get switch off

Posted on Mar 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove the front wiper blades on a 1987 gmc jimmy so that i can remove the wiper motor


If you're talking about the wiper ARM pull the wiper away from the windshield and at the base of the arm you should see a little clip.
Get a little screwdriver or needle nose pliers and pull the clip away from the base. It will not come all the way off, when it is pulled away just jiggle the arm at the base while pulling up. It might take some jiggling but it will come off.

Feb 04, 2015 | GMC Cars & Trucks

2 Answers

The rear windshield wiper motor needs to be replaced. where is it and how can i get to it?


MARK THE POSITIONS OF THE WIPER ARM ON THE LIFT GATE GLASS,THEN REMOVE WIPER ARM COVER AND NUT AT THE OUT SIDE LIFT GATE, THEN THE BEZEL.BECAREFUL DONT DAMAGE PAINT.ON THE LIFT GATE.AND REMOVE THE UPPER AND LOWER LIFT GATE TRIM PANELS.DISCONNECT THE ELECTRICAL CONNECTOR AT THE REAR WIPER MOTOR, THEN REMOVE THE TWO MOUNTING BOLTS SUPPORT WIPER MOTOR WHILE REMOVING BOLTS.THEN INSTALL NEW WIPER MOTOR AND PUT EVERY THING BACK IN PLACE VISA VERSA.

May 26, 2011 | 1998 GMC Jimmy

1 Answer

Where is the wiper motor on my 1999 GMC Yukon?


Windshield Wiper Motor
Removal & Installation
To Remove:


  1. Remove wiper arms.
  2. Remove weatherstrip from cowl.
  3. Remove two cowl vent grille panel screws.
  4. Remove windshield nozzles and hoses.
  5. Remove three cowl vent grille panels.
  6. Disconnect windshield wiper motor electrical connector.
    NOTE: Do not remove crank arm from windshield wiper motor.

  7. Loosen nuts that attach the drive link brackets to the crank arm.
  8. Remove wiper motor crank arm brackets.






    gm-06-00-1079.gif



  9. Remove three bolts and windshield wiper motor from vehicle.

To Install:


  1. Install windshield wiper motor and three bolts.

    • Torque to: 62 in lbs. (7 Nm)

  2. With right side linkage closest to the windshield wiper motor, install drive
    link brackets to wiper motor crank arm.

    • Torque nuts to: 44 in lbs. (5 Nm)

  3. Connect electrical connector.
  4. Install nozzles and windshield washer hoses to cowl vent grille.
  5. Install three cowl vent grille panels and screws to vehicle.
  6. Install weatherstrip to cowl.
  7. Install wiper arms.


prev.gif next.gif

Oct 30, 2010 | 1999 GMC Yukon

1 Answer

The windshield wiper on the drivers side does not work. Sometimes when you turn them on it wigs out and flings clear over to the side view mirror. Is their any way I can fix it myself?


Hi, the wiper arm is held on with a 13mm nut. with the wipers off, remove the plastic cap on the nut, and simply tighten this nut,(with the arm in thecorrect position, you should be able to move the arm by hand, while it is loose. Good luck...

Sep 23, 2010 | 2000 GMC Jimmy

1 Answer

My wiper on my 2000 gmc jimmy went crazy. I cant


its part of combination switch need to remove steering column cover to get switch off

Mar 19, 2010 | 2000 GMC Jimmy

1 Answer

Wiper arm removal 1997 GMC Jimmy


youll have to raise the hood on the truck to access the screws that hold it in place there should be 2 of them holding it

Oct 25, 2008 | 1997 GMC Jimmy

Not finding what you are looking for?
2001 GMC Jimmy Logo

655 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...