Question about 1984 Pontiac Parisienne

1 Answer

Windshield Washer doesn,t work - 1984 Pontiac Parisienne

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 140 Answers

It may be the washer motor is bad. Check to see if the fluid is high enough first.

Posted on Sep 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1995 Ford Ranger's windshield wipers don't work


That involves airbag removal & a lot of delicate work. Let someone experienced handle it.

Jul 15, 2017 | Ford Ranger Cars & Trucks

1 Answer

How to remove windshield washer pump


sounds like the spray nozzles are clogged you can usually remove them and soak them in soapy water or spray water through it with a sprayer on the end of a hose. if that doesn't solve it then you may have a cracked line or the pump that pumps it out may be broken but usually is the nozzles are clogged.

Sep 23, 2012 | 2002 Pontiac Bonneville

1 Answer

Windshield washer fluid doesn't squirt after windshield replacement


They probably knocked loose one or more of the tubes that carry the washer fluid. Try to trace the lines back from the sprayer nozzles and you may find the problem.

Sep 17, 2012 | 2006 Nissan Frontier

1 Answer

Windshield wash doesn't work


Hello! Defective washer pump relay...Under hood box...# 33 (Front washer)...Guru...saailer

Feb 02, 2012 | 2005 Ford Expedition

1 Answer

Windshield washer fluid lamp will not shut off. It is full. States that i need to add windshield washer fluid and it is full, how do you reset the sensor. ?


sometimes that takes a few starts and stops, if it doesn't clear in a couple of days unhook the battery wait 5 minutes and hook it back up

Jul 11, 2011 | 2008 GMC Sierra 1500

1 Answer

2001 Escape. Rear window washer doesn't work. No noise. Front one works. Is there a relay? Where?


I belive on the bottom of the washer fluid resivor their is a pump for the front windshield and a pump for the back glass that pump may be bad.

Jun 05, 2011 | Ford Escape Cars & Trucks

1 Answer

Located washer fluid rear windshield


Sometimes the rear washer fluid tank is located in the rear hatch area. you may see it when you open the hatch, it will be on the side with a cap covering where you wouuld put the fluid in. If the nozzle is clogged you can use a small pin and stick it in the hole to try to dislodge ant debris in the hole.

Jun 03, 2010 | 2004 Hyundai Santa Fe

1 Answer

Mercury villager 1994 washer pump not working


the pump motor likely is bad. get a used washer fluid reservoir at a pick n pull yourself or at car-part.com. page with * is lowest cost.

Pump and Reservoir, Windshield Washer Removal
  1. Disconnect the battery ground cable (14301).
  2. Raise and support the vehicle.
  3. Remove the RH wheel (1007).
  4. Remove the RH front fender splash shield (16103). Refer to Section 01-02 for the removal procedure.
  5. Remove the windshield washer reservoir top bolt.

  6. Disconnect the windshield washer reservoir fluid level sensor electrical connector.
  7. Disconnect the rear window washer pump electrical connector from the rear window washer pump.
  8. Disconnect the windshield washer pump electrical connector from the windshield washer pump (17664).
  9. Place a suitable drain pan under the windshield washer reservoir (17618) and drain the washer fluid.
  10. NOTE: The rear window washer hose end is color-coded, matching the connector on the rear window washer pump. Match the colors to ensure proper installation.

    Disconnect the washer hoses from the windshield washer pump and the rear window washer pump on the windshield washer reservoir.

  11. Loosen the two windshield washer reservoir side bolts.
  12. Remove the windshield washer reservoir by sliding it out of the side slots.
  13. Remove the windshield washer pump.

    Installation
To install, reverse the removal procedure. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).

Sep 09, 2009 | 1994 Mercury Villager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...