Question about Toyota Sequoia

Open Question

How can i fix sencer p1441 & p1442 toyota sequoia 2005

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1986 Answers

SOURCE: want to fix the passenger side mirrow motor for

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you can remove the bolts holding the mirror onto the door and disconnect the cables from the mirror going into the door

Posted on Sep 03, 2009

  • 1861 Answers

SOURCE: how to program 2005 toyota sequoia garage door

Hello.I will be glad to help you out.

Choose which of the 3 buttons you wish to use, on the car.

Take the remote transmitter, depress the actuator button, and continue to hold it until advised to release.

Depress the button, on the car, of your choice, and hold it down until advised to release.

Hold the garage door actuator (while holding the actuator button down) above the car's 3 buttons.

Rotate the door transmitter until the red light above the 3 buttons starts to flash slowly.

Stop moving the remote around when the light flashes slow.

Within several seconds, the same light n the car will now flash rapidly.

Release the car's button, release the transmitter button.

Verify that the door now operates..

Posted on Nov 30, 2009

duane_wong
  • 6826 Answers

SOURCE: Where is the oil drain

Look under the engine (not the transmission) for the drain plug on the engine oil pan.

The following is some information on how to change the oil pan:
REMOVAL & INSTALLATION 3.4L Engine

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Drain the engine oil.
  4. Remove or disconnect the following:
    • Engine undercover
    • Front differential, if equipped with 4WD
    • Oil pan, separate it from the engine using SST 09032-00100 and a brass bar
    To install:
  5. Apply seal packing to the oil pan.
  6. Install the oil pan to the cylinder block. Tighten the nuts and bolts to: 67 inch lbs. (8 Nm) WARNING
    If parts are not assembled within 5 minutes of applying time, the effectiveness of the seal packing is lost and must be removed and reapplied.
  7. Install or connect the following:
    • Front differential, if removed
    • Engine undercover
    • Negative battery cable
  8. Fill with engine oil.
  9. Start the engine and check for leaks.
4.7L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove the engine from the vehicle and mount it on a stand.
  3. Remove or disconnect the following:
    • Oil dipstick tube
    • Lower oil pan
    • Oil pan baffle
    • Upper oil pan
    To install: Fig. 1: Upper oil pan bolt location — 4.7L engine 7924sg75.gif

  4. The upper oil pan bolts are different lengths and are identified as follows:
    • A: 0.79 inch (20mm) w/10mm head
    • B: 0.98 inch (25mm) w/12mm head
    • C: 2.36 inch (60mm) w/12mm head
    • D: 1.38 inch (35mm) w/10mm head Fig. 2: Upper oil pan sealant application — 4.7L engine 7924sg74.gif

  5. Apply silicone sealant to the upper oil pan as shown.
  6. Install the upper oil pan and tighten the fasteners in several passes to the following specifications:
    • 10mm: 66 inch lbs. (7.5 Nm)
    • 12mm: 21 ft. lbs. (28 Nm) Fig. 3: Lower oil pan sealant application — 4.7L engine 7924sg76.gif

  7. Install or connect the following:
    • Oil pan baffle. Tighten the fasteners to 66 inch lbs. (7.5 Nm).
    • Lower oil pan. Tighten the fasteners in several passes to 66 inch lbs. (7.5 Nm).
    • Oil dipstick tube
  8. Install the engine.
prev.gif next.gif

Posted on Sep 01, 2010

  • 1509 Answers

SOURCE: My 2005 Toyota Sequoia rear

first decide if your going though the right things to turn it on as he key needs to be on for it to work with it on go back arounf=d and see if tryig to ust it makes it work if it does it may have been just stuck. After that your trying to detenine that made it stop. The fuse it theunder dash fuse apanel theres a circuit breaker they can fail if the wiper stayed stuck too long. Testing the fuse for power with a test light ( test light; an ice pick with a clear handle with a light bulb inside ad a grounding wire on the end with an allagater clip attached ) connect the light to ground and (look ) for power with the tip as it lights you( see) the power. You may have to look right at the wiper motor. With the cover removed on the rear lid youshould be able to see the motor for te wiper and its plug in connections. with the key on and the test light connected to a good ground, the light should light in all positions of the switch on one or another wire going into the motor. One wire will be ground and it should'nt light the light ( its black). If the ground is good and powers getting to it then the motors badand, take it with you to the parts store to get another one. Have them test yours and also show you the one their selling ou is ood as it's no fun to change it twice. You may decide to get a used one, after they tell you what they want for a new or rebuilt one. Make sur the used one works or that they;ll garentee it before you leave te used parts store ( Junkyard). They want to sell goodpartsand they'll tst yours and theirs too.

Posted on Nov 06, 2010

johnjohn2
  • 5763 Answers

SOURCE: I got a toyota sequoia

The fuel filter is located inside the gas tank, the filter should last the life of the pump. i work on many models with this design and never had a problem, i tell customers it lasts the life of the pump. your fuel filter doesnt need replacing, it will last the life of the pump, it gets replaced with the fuelpump when it goes,good day.

Posted on Apr 10, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Toyota Sequoia shuts down while driving


It is possible that your cam angle sensor is on its way out. Have it checked asap, it will choose a lonely, deserted road miles from nowhere to finally let you down.

Mar 02, 2015 | 2005 Toyota Sequoia

1 Answer

Looking for upper and lower ball joint torque specs 2005 Toyota sequoia


What is theTorque on front ball joints 2005 Toyota sequoia ...

www.fixya.com/cars/t25021879-thetorque_front_ball_joints_2005_toyotaAug 28, 2014 - Tightening specs for castle nuts - Toyota 2005 Sequoia question. ...There are no torque specs for the upper or the lower ball joints on any of

Aug 28, 2014 | 2005 Toyota Sequoia

1 Answer

2005 sequoia limited and just new rotors and pads on front and refaced rotars and break pads in the back. Brakes make noise when shifting from park to drive or reverse and vice versa. Any idea the cause?


I have heard that Toyota's are sensitive to off brand brakes. IF you did not use Toyota brake pads, you might need to wait and see if it goes away with time. If not use Toyota pads.

Apr 10, 2014 | 2005 Toyota Sequoia

2 Answers

How do you remove a broken rear door handle for a 2005 toyota sequoia?


well you can crawl across inside and open . inner door panel has to be removed to access the screws or bolts that hold handle

Feb 26, 2013 | 2005 Toyota Sequoia

1 Answer

I got a Error Code P1441 Definition EVAP System Flow During Non-Purge Conditions Possible Causes: EVAP purge valve, purge pipe, or the charcoal canister has a temporary blockage (this fault could...


P1442 usually gas cap. P1449 usually vent solenoid. P1441 usually always a faulty FTP sensor. Very problematic to Malibu, Grand Am Cavaliers and Aleros. That would be my first area to check. They are also known for poor wiring connections at the Left rear passthru connector to the fuel tank and vent solenoid, but not necessarily for that code.

Jan 25, 2011 | 2001 Pontiac Grand Am SE

2 Answers

Dtc 1442 and 1446


P1442
The code actually has another character in front of it, most likely a P (Powertrain) code as they're most common, although it could also be a B (Body) or C (Chassis) code. So it's likely P1442 and it's description is Evaporative Emission Control System Leak Detected. That code is specific to Toyota vehicles, although it seems nearly identical to the generic code P0442. This error pertains to the emissions system in the car. You now have the choice of either taking the car to a qualified technician or you can try a few troubleshooting steps yourself. If you're not mechanically inclined, I would recommend you change the gas cap to a brand new Toyota one (not a cheap aftermarket one), reset the code and see if it comes back. If the code returns there are additional steps you can take. Take a look at this P0442 article for other ideas.

May 18, 2010 | 2006 Toyota Sequoia

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

682 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...