Question about 1995 Mercury Sable

Open Question

1995 mercury sable no spark has new coil new ignition module and still no fire has power on both coil wires could it be crank sensor

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
pippall
  • 1486 Answers

SOURCE: cranks but wont start

possible timing belt slipped or broken.

Posted on May 30, 2009

Ad
boysor2933
  • 293 Answers

SOURCE: 89 jeep cherokee 4.0 cranks and gets fuel but no

If you can access a good engine control module (computer) replace it to your unit and try starting the engine again.

Posted on Jun 01, 2009

  • 30 Answers

SOURCE: no spark from ignition coil

did you reuse the balace shaft if you did have you check the teeth or it may ecm problem

Posted on Jun 09, 2009

  • 52 Answers

SOURCE: 1995 mercury sable.turn key and car cranks over

use a test light and see if power is going to the coil. if yes then use a spark tester from a auto parts store. it will have settings for your vehicle. if the spark is not big enough it's just the same as not having one. then change the coil. if you don't get power before the coil have the ignition control modual checked. if bad replace it. good luck.

Posted on Oct 12, 2009

  • 1 Answer

SOURCE: My 95 Mercury Sable won't start I am getting spark

My 95 mercury sable drives a while then splutters and dies. after it sits a while it starts. It only seems to do this whem its hot outside and has run a while

Posted on Jun 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1995 mercury sable i get no spark it has the 3.8l .it also has a ditribitor and coil packs why am i getting no spark replaced plugs coil packs distributor


Ignition control module ? Is there B+ voltage on the red an lit green striped wire at the ignition coil ? Watch this video on how to trouble shoot . This is a ford pick up ,ignition system similar . 1996 Ford 150 No Start with ScannerDanner EricTheCarGuy

Jan 08, 2016 | Mercury Cars & Trucks

1 Answer

Have a 1986 chevy celebrity tec4 an have no fire from coil ive replaced coil checked fuses an have power going to coil still no fire


ignition will trigger if signal from crank sensor, with hei spark plug tester ,read to coil wire and spark plugs wire if spark , depends wich engine
if c3i coil and module the module could be the problems you can check it before replace
hope it helps

Mar 29, 2014 | 1986 Chevrolet Celebrity

1 Answer

1995 mercury sable no fire from ignition coil


MAke sure its in park( just move it though the gear shifts) sometimes the neutral switch gets sloppy age/usage/transmission swap etc. Check for voltage at the coil positive terminal when the ignition key is on. YES there is voltage, the problem is on the trigger side of the coil (pickup, crank sensor, ignition module or primary wiring circuit). If there is NO voltage at the coil, the problem is on the supply side (the ignition switch or ignition wiring circuit). Check Relays and Fuses.

Mar 08, 2013 | 1995 Mercury Sable

3 Answers

I have a 1996 mercury sable that wont srat i pulled up at home about 2 hours later tried o leave and it did not start, i checked the coil pack for a spark and it gave no fire, so i replaced the coil pack...


Probably the crank sensor, do you hear the fuel pump 'buzz' when you turn on the key (not cranking the engine, just key on)? If you do hear the fuel pump (only lasts about 2 seconds), it may be the ignition module, otherwise it is probably the crank sensor.

Jul 20, 2011 | 1996 Mercury Sable

1 Answer

1995 ford probe new engine no spark


did you install the crank sensor?

Mar 23, 2010 | 1995 Ford Probe

2 Answers

1995 ford explorer doesn't start, crank & cam sensors replaced


Does you fuel pump delivers fuel. Is it there a spark.

Dec 29, 2009 | 1995 Ford Explorer

3 Answers

My 95 Mercury Sable won't start I am getting spark from the ignition coil but none from the distributor I replaced the ignition module not sure what to do next


remove distributor cap,check for moisture or poor condition of 'contacts' on rotor & inside cap.check for a clean connection at coil to distributor lead,check spark plug wires.

Oct 12, 2009 | 1995 Mercury Sable

1 Answer

1995 mercury sable.turn key and car cranks over but no spark from coil.


use a test light and see if power is going to the coil. if yes then use a spark tester from a auto parts store. it will have settings for your vehicle. if the spark is not big enough it's just the same as not having one. then change the coil. if you don't get power before the coil have the ignition control modual checked. if bad replace it. good luck.

Oct 12, 2009 | 1995 Mercury Sable

1 Answer

Need to know what fires coil 1995 mercury sable both wires to coil have power when key is turned on car cranks no spark from coil new coil what gives the coil extra power to fire


what engine? 3.0L 2 Valve? 4 Valve?
3.4L SHO engine?

The PCM (engine computer) fires the coils, but it is never the cause of a problem. I suspect it is the crankshaft position sensor on the front of the engine by the crank pulley. easy to change.

Crankshaft Position Sensor The crankshaft position sensor (CKP sensor) (6C315) is a variable reluctance sensor triggered by a 36-minus-1 tooth trigger wheel located on the crankshaft pulley and damper. The signal generated from the crankshaft position sensor is called the crankshaft position (CKP) signal, which provides base timing and crankshaft speed (rpm) information to the ignition control module (ICM) (12K072). Base timing is set at 10±2 degrees before top dead center (BTDC) AND IS NOT ADJUSTABLE. The powertrain control module (PCM) (12A650) will use this information with the spark advance information to determine ignition coil (12029) turn on or turn off time.

Sep 15, 2009 | 1995 Mercury Sable

1 Answer

No spark from coil


I had the same problem with my 97 sable it turned out to be the ecm module.

Sep 06, 2009 | 1995 Mercury Sable

Not finding what you are looking for?
1995 Mercury Sable Logo

Related Topics:

293 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...