Question about 2003 Jeep Wrangler

Open Question

How to bleed brakes on 2003 jeep wrangler - 2003 Jeep Wrangler

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6982 Answers

SOURCE: clutch

Bleeder screw should be somewhere on the slave cylinder, generally somewhere above the centerline of the unit. (unless someone snapped it off. If that's the case, sometimes you can drill it out, but this takes a lot of skill mixed with some luck. (You can't damage the threads at all, and if you go too deep you will damage the sealing surface). Therefore better to replace it.

Posted on Jan 02, 2009

cat_daddy887
  • 2 Answers

SOURCE: how do I bleed hydraulic clutch in 1991 jeep

There is a bleeder on the drivers side of the transmission follow the tube from the clutch master cylinder if you cannot find it. Pump the clutch up and hold it down then open the bleeder repeat till air is gone. May have to bleed again after driving a bit. If you want to bleed the clutch master cylinder run a tube from where the line goes into the cylinder and take the cap off and run the tube into the fluid (make sure its in the fluid) then pump the clutch slowly until no air bubbles. I just replaced my clutch master cylinder this is where the information comes from hope it helps you out!

Posted on Apr 05, 2009

redbeard00
  • 957 Answers

SOURCE: how do i bleed the master clutch cylinder system on a 1995 jeep ?

A special pump is used to back bleed the system. If you don't own one then you have to be patient and just keep pumping the clutch pedal until it comes back. It can take a half hour to get it back. Just depents on how much air is inside.

Posted on Jun 16, 2009

  • 141 Answers

SOURCE: how do i bleed the clutch slave cylinder on a 95

pump up clutch pedal really fast about ten times....leave it held to floor....open bleeder on slave cyl... repeat untill you have good pedal....may need to adjust master cyl. rod on clutch pedal to get more travel....good luck....Lee

Posted on Nov 06, 2009

techbuster
  • 5081 Answers

SOURCE: bleeding brake system how?

BLEED BRAKE SYSTEM

Make sure one end of the Jeep is raised (starting with the rear end) and secure on jack stands and the wheels on each side have been removed. If you have been working on the brakes, this should already be done.

Connect a clear rubber tube to the bleeder valve on the right rear brake caliper. Start with this end and side because it is farthest from the master cylinder.Place the tube's other end into a container partially filled with brake fluid.

Open the bleeder valve on the caliper and have an assistant press on the brake pedal inside the Jeep. Look for a mixture of air and fluid to come out of the valve. Once all the air is purged and the fluid runs cleanly from the valve, close the screw and remove the tube.

Repeat the process for all four brakes. Move to the left rear next, followed by the right front and the left front. If you need to, reconnect the Jeep's rear wheels and lower the rear end before raising the front end and removing those wheels.

Check the level of fluid in the master cylinder periodically as you bleed the brakes. If the level drops below the needed fill line, add more fluid. Use fresh fluid, not any that you have bled from the brakes.

Start the Jeep's engine after bleeding all the brakes and press on the brake pedal. You might need to do this repeatedly to seat new brake pads you just installed. Turn off the engine and hold down on the pedal. Bleed the brakes again if the pedal sink within 15 to 20 seconds.

Posted on Dec 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the flasher relay on my jeep wrangler


it should be in the fuse box under the dash driver side by the brake pedal

Mar 04, 2015 | 2003 Jeep Wrangler

1 Answer

How do you do you bleed a clutch line on a 1993 jeep wrangler?


Just like you would bleed brakes. Fill the reservior with brake fluid, open the bleeder screw and have a friend press the clutch pedal in. Close the bleeder screw and let up on the clutch. Do that until the clutch pedal has a good feel. Be sure to check the reservoir frequently as they don't hold much fluid and if you let it get low you'll **** more air into the system.

Jul 31, 2010 | 1993 Jeep Wrangler

2 Answers

98 wrangler - brake pedal goes all the way to the floor. The master cylinder and all brake lines are free of leaks. I'm not losing any brake fluid anywhere. I replaced the booster that is attached to the...


You changed the master cylinder and vacuum booster and have no leaks anywhere, but did you bleed the entire brake system after you did this work? A little bit of air in any of the lines will make the brakes ineffective.

May 30, 2017 | 1998 Jeep Wrangler

2 Answers

Where is the bleed valve for clutch on a 1991 jeep wrangler


1. Fill master cylinder reservoir with DOT 3 brake fluid. Raise and support vehicle. Attach bleeder hose to bleeder screw on bleed line of slave cylinder. See Fig. 1 (attached in link) . Place other end of hose in glass container 1/2 full of brake fluid. Loosen bleeder screw while holding bleeder screw fitting.

2. Have an assistant depress clutch pedal to the floor. Tighten bleeder screw and release clutch pedal. Repeat bleeding procedure until fluid entering container is free of bubbles. DO NOT allow reservoir to run out of fluid during bleeding. Refill clutch master cylinder reservoir.

CAUTION: DO NOT allow bleed line to bend or flex when loosening
bleeder screw.

FIG1: http://anubiscycle.com/fixya/91wranglerslaveassy.png

Jan 14, 2010 | 1991 Jeep Wrangler

2 Answers

Where do you bleed the hydralic clutch on 1998 Jeep Wrangler 6 cyl.


you can do this at the slave cylinder down at the transmission make sure the resvoir is full and bleed like you would brakes

Jan 02, 2010 | 1998 Jeep Wrangler

1 Answer

Just put a set of rear brakes on my 1990 jeep wrangler an i still have no pedal presure


it sounds like you need to bleed the brakes. If the pedal will not pump up to bleed the brakes then you must have bad master cylinder. We just had the same problem with my wifes truck. Her brakes went to the floor and would not pump up. It was the master cylinder.

Oct 15, 2009 | 1990 Jeep Wrangler

1 Answer

Inoperative brake lights


try refitting bat make sure you have all wires on the connectors, maybe you have blown the bulbs but sounds like a wire somewhaire

Jun 05, 2009 | 2003 Jeep Wrangler

1 Answer

Brake fluid seems to be full


bleed brake lines they have air in them

Mar 21, 2009 | 1993 Jeep Wrangler

Not finding what you are looking for?
2003 Jeep Wrangler Logo

Related Topics:

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...