Question about Chevrolet 2500

Open Question

How to replace rear axle seal on diesel gmc 3/4 ton

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Rear Axle Removal

if you are talking about the axle seals, 1.REMOVE THE WHEELS.2. REMOVE THE DIFF COVER(slowly)3.REMOVE THE BRAKE CALIPER ASSEMBLY.4.REMOVE THE 8MM PIN IN THE DIFF CARRIER. 5.TURN CARRIER AND REMOVE THE LARGE PIN.6. FIRMLY HIT IN THE AXLE, A SMALL RETAINING C CLIP WILL FALL INTO THE DIFF HOUSING. DO THE SAME WITH THE OTHER SIDE. ( be careful if you have rear speed sensors remove it when you remove the brake calipers . you will break it when you are pushing in the axles.)7.pull axles and replace seals

Posted on May 30, 2008

  • 4 Answers

SOURCE: Rear Axle Leak

It might be the bearings that failed and letting the axle rest on the seal. Its a common problem for these cars. I've replaced mine and it did it again so now im replacing the rear end.

Posted on Jan 19, 2009

  • 52 Answers

SOURCE: Rear Axle Seal Replacement

remove rear tires, then remove brake calipers and rotors, then remove the 4 nuts (each side) that hold the axle shafts to the axle tube (located around the axle tube behind the backing plate) then using a slide hammer pull the axle shafts out, next using a die grinder and an air hammer get he retainer collar and the bearing off (without damaging the axle shaft) then remove the seal and the outer race which will still be in the housing. next put it all back together, make sure the plate with the studs is still on then slide the seal, bearing, then retainer on (all new parts) and using a press push them all the way back on. then is simple reassembly.

Posted on Apr 22, 2009

  • 335 Answers

SOURCE: REAR AXLE SEAL LEAKING ONTO BRAKE SHOES NEED INSTRUCTIONS ON HOW TO FIX

Jack up vehicle and support on stands. Remove wheels. Remove differential cover . Locate and remove lock pin that holds cross shaft in. Slide cross shaft out. Push axle inward to release axle c clip. Remove axle and pry out old seal. Install new seal with proper tool.Add some lube to the seal lip to aid axle intallation. Revese removal procedure. This is for a "c" type axle.
Another type has 4 nuts attaching a retainer plate to the backing plate behind the axle flange. In this case the 4 nuts are removed and the axle will come out. This may require a little effort. I think that you have a "c" type axle in your vehicle. Hope this helps. Moe

Posted on Apr 28, 2009

roniecon
  • 6826 Answers

SOURCE: Replaced rear axle pinion bearing and seal, need

There is no torque specs,this nut has to be tightened back like it was ,the best thing to do,was,to late now,is to use a torque wrench to remove the nut,and remember the torque,and when replacing it,torque it back to that spec,the reason being,there is a crush sleeve between the front pion bearing ,and the rear pinion bearing,and it has to be crushed to a certain amount,to aquire deepness into the ring gear,anyway just give it about 25 lbs torque,any more the crush sleeve will crush even more and the deepness of the pinion will be too much.

Posted on Apr 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you pull a 1979 gmc jimmy 4x4 rear right axle


QU40221 19 Spline Outer Axle Shaft for 1977 to 1991 Chevy, GMC Corporate GM 10 Bolt Front Axle is a genuine original equipment outer axle stub shaft for all GM 10 Bolt front axles in 1977 to 1991 Chevy Blazers, GMC Jimmys, and Suburbans, plus Chevy, GMC 4x4 1/2 ton and 3/4 ton Pickups. The splined end on these new axle shafts has three snap ring grooves in three places so they are compatible with all types of automatic and manual lockout hubs plus all full-time solid splined drive gears.

Also available while supplies last: QU40221U Used Outer Axle Shaft with 3 snap ring grooves and QU40660UUsed Inner Axle Shafts with 2 snap ring grooves (QU40660U is not compatible with automatic locking hubs)



see this vdio

Apr 01, 2015 | GMC Jimmy Cars & Trucks

1 Answer

How do i change the seals in a rear end in a 1985 chevy 3x4 ton pick up


Pinion seal? Wheel bearing seals? Several different rear axles could be in your 3/4 ton--full float or semi-float. Once again you are wise to buy a cheap shop manual which will tell all.

Dec 17, 2014 | Cars & Trucks

1 Answer

1984 Chevrolet Custom Deluxe rear hub service


If you can see inside the wheel bearings then they require lubrication from the differential. If they are sealed then no. You don't say if the rear axles are 1/2 ton or 3/4 ton. No brand of seal will seal better than any other. Spray engine degreaser in the rear end and flush out with water. You may need to do that more than once.

Mar 30, 2013 | 1984 Chevrolet C1500

1 Answer

2005 GMC 4x4 HD 2500 6.0 eng. rear axel seal


SEAL COULD BE LEAKING CAUSE YOU DIDNT LUBRICATE THE SEAL LIPS WITH PETROLEUM JELLY TO HELP THE THE SEAL LIP SEAL OR YOU DAMAGE THE SEAL WHILE DRIVING IT IN.AXLE FLANGE NUTS TORQUE IS 58 FT LBS THE AXLE HUB NUT TORQUE IS 177 FT LBS.

Jul 14, 2010 | 2005 GMC Sierra 2500HD 4WD

1 Answer

I need rearend stamatics for a 1993 GMC 3500. Can anyone help me find the stamatics?


Schematics for these rear axles are many. I will need the axle code to fetch the correct ones for you. A one ton have 14 different rear axle designs

Apr 11, 2010 | GMC Sierra 3500HD Cars & Trucks

1 Answer

Need detailed manual or assistance in replacing left rear axle seal and bearing on 2005 GMC Sierra pickup with 5.3L engine and a 324 rear end


You'll need to remove the rear end cover, remove the pin in the center pumpkin, push axle toward the center of vehicle and remove the axle clip, pull out axle. You may need a bearing puller to remove bearing.

Mar 04, 2010 | 2005 GMC Sierra

1 Answer

How do I remove the rear axle to replace the seal 1996 jimmy


You will have to remove the differential cover on the rear end, in the center of the gear cluster you'll have to rotate your axle until it exposes the ends of the axle shafts, push in the axles as far as you can from the brake pad assembly area, then, there this a C clips that slips into a groove on the end of the axle, you'll have to reove the C clip to pull out the axle.

Apr 25, 2009 | 1996 GMC Jimmy

1 Answer

Rear axle seal leaking on 1997 GMC Yukon 4x4


You are Talking about the Main Cover on the Rear of the Rear end Correct???? If so, This is Just a Gasket and is Very easy to replace. The Gasket is Simply Worn out.

Jan 17, 2009 | 1997 GMC Yukon

1 Answer

2000 gmc both rear tire oil leakage.


You are correct, it's not brake fluid. Check the level in your rear axle, it sounds like you have bad seals in the axles allowing the rear differential gear oil to leak inside the brake drums.
This is a heavy weight oil, 80 or 90 weight. This leakage will ruin your brake pads, and if enough leaks out, your rear differential will blow. The seals aren't expensive, but it's a lot of labor to pull everything apart to get at the seals, plus new rear brakes. My Ford ( and I'm sure your GMC) require removal of the rear axles to change the seals. Good Luck! countrycurt0

Sep 17, 2008 | 2000 GMC Sierra

2 Answers

Have to replace rear wheel bearings on 1987 sierra half ton


Not extremely hard just need the right tools for it and a manual.

Aug 12, 2008 | GMC Sierra Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...