Question about 1999 Cadillac Eldorado

1 Answer

How do i replace a cv joint on 1999 cadillac eldorado

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 385 Answers

Lots of trouble and expense and all you get is one new joint. trade that labor expense and for about the same money get a new or reconditioned axle that has 2 good cv joints, boots, and new axle. and you can change out the whole axle yourself much easier than the joint.

Posted on Sep 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Driver seat back is lying down on the back seat. Can't get it to stay in the upright position.


On the web

Power seat operation erratic : Cadillac Eldorado Common ...

repairpal.com > Problems > Cadillac > Eldorado
Cadillac Eldorado Power seat operation erratic. This is a verified problem based on 26 reports. Learn more about this problem, when it occurs and how to fix it. ... 13 model years affected: 1990, 1991, 1992, 1993, more1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002 ... Come back and drivers seat will not move.

Aug 04, 2015 | 1999 Cadillac Eldorado

1 Answer

Replace rubber cv boot on 1999 Isuzu rodeo


how to , who can, what are all steps. are there special tools?
sure. if the boot is bad, so be the joint, Yah think?
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Halfshaft from the vehicle
    • Snapring and bearing
    • Snapring and oil seal
    • Mounting bracket
    • CV-joint boot
    • Circlip and inner joint housing
    • Snapring and spacer
    • Inner joint balls
    • Snapring and inner CV-joint
    • To install:
    • Install or connect the following:
      • Inner CV-joint and snapring
      • Inner joint balls
      • Spacer and snapring
      • Inner joint housing and circlip. Add 150 grams CV-joint grease.
      • CV-joint boot
      • Mounting bracket
      • Oil seal and snapring
      • Bearing and snapring
    • Install the halfshaft and mounting bracket to the vehicle.
    • Check the wheel alignment and adjust as necessary.

Jun 30, 2014 | 1999 Isuzu Rodeo

1 Answer

Replace lower ball joints. How do you replace Lower ball jonits?


REMOVAL & INSTALLATION
  1. Raise and safely support the vehicle, allowing the front suspension to hang free.
  2. Remove the wheel and tire assembly. WARNING
    Be careful when working in the area of the CV-joint boot. Damage to the boot could result in eventual CV-joint failure. If necessary, install CV-joint boot protector tool J-34754 or equivalent, to protect the boot.
  3. On Eldorado and Seville with 4.6L engine, remove the road sensing suspension position sensor from the lower control arm.
  4. Remove the cotter pin and nut from the ball joint stud. Use ball joint separator tool J-36226 or equivalent, on Deville and Fleetwood or ball joint separator tool J-35315 or equivalent, on Eldorado and Seville, to separate the ball joint from the steering knuckle.
  5. On Deville and Fleetwood, loosen the stabilizer bar link nut.
    1. Drill out the 3 rivets retaining the ball joint to the lower control arm and remove the ball joint. NOTE: Recommended drill-bit is 1⁄2 inch (13 mm). Fig. 1: Drilling the rivets out of the lower control arm 91048g05.gif
      Fig. 2: Installing the bolts in the lower control arm 91048g06.gif
      To install:
  6. Attach the new ball joint to the lower control arm with 3 mounting bolts and nuts.
    1. On Deville and Fleetwood, the bolts must be installed from the top of the control arm.
    2. On Eldorado and Seville, the bolts must be installed from the bottom of the control arm
    3. Tighten the nuts to 50 ft. lbs. (68 Nm).
    4. On Catera, the bolts must be installed from the top of the control arm.
    5. Tighten the nuts to 26 ft. lbs. (35 Nm).
  7. On Deville and Fleetwood, tighten the stabilizer bar link nut to 13 ft. lbs. (17 Nm).
  8. Connect the ball joint to the steering knuckle and install the castellated nut.
  9. On Deville and Fleetwood, tighten the ball joint nut to 88 inch lbs. (10 Nm). Then tighten the nut an additional 120°, during which a tighten of 41 ft. lbs. (55 Nm) must be obtained.
  10. On Eldorado and Seville, tighten the ball joint nut to 84 inch lbs. (10 Nm). Then tighten the nut an additional 120°, during which a minimum torque of 37 ft. lbs. (50 Nm) must be obtained. If the minimum torque is not obtained, check for stripped threads. If the threads are okay, replace the ball joint and knuckle.
  11. On Catera, tighten the pinch bolt to 74 ft. lb. (100 Nm).
  12. Install a new cotter pin. If the cotter pin cannot be installed because the hole in the stud does not align with a nut castellation, tighten the nut up to an additional 60°to allow for installation. NEVER loosen the nut to provide for cotter pin installation.
  13. On Eldorado and Seville with 4.6L engine, install the road sensing suspension position sensor to the lower control arm.
  14. If necessary, remove the CV-joint boot protector tool.
  15. Install the wheel and tire assembly and lower the vehicle. Fig. 3: Separating the ball joint from the steering knuckle 84208016.gif
    Fig. 4: Lower ball joint installation - Deville and Fleetwood 84208017.gif
    Fig. 5: Lower ball joint installation - Eldorado and Seville 84208018.gif

Jan 17, 2011 | 1991 Cadillac DeVille

1 Answer

License Plate Lamp Replacement on 1999 Cadillac Eldorado ETC. Where is the access point for replacing the licence plate lamps?


Hello, remove the rear license plate, remove the housing where the license plate was mounted, now you can see how to replace the bulbs.

Sep 05, 2010 | 1999 Cadillac Eldorado

1 Answer

How to replace CV joint


jack up vehicle, remove wheel, remove split pin from hub nut, remove nut, remove lower ball joint nut & separate ball joint, lever lower arm down, pull hub forward while pushing cv joint in wards through hub, remove cv gaiter clips and slide back on shaft, hold shaft firmly and knock cv joint off with hammer, pack new joint with grease, and place on shaft with nut on threads carefully knock on with hammer, re-fit parts in reverse order

Apr 24, 2010 | 1999 Hyundai Accent

1 Answer

The best way to take out an engine of a 2002 Cadillac Eldorado


u have to drop the sub frame . meaning the transmission and motor gotta come together. unblot the torque strut located on top of the raditor and motor. unbolt strut towers. unbolt drive axles . use a large screw driver and a hammer and tapp out drive axles (cv joint). unblot subframe (slowly) . unbolt the rear part of subframe first so u can get to steering gear. and remove the shaft from the steering gear. and that should be it. also if doing this without a lot of shop equipment. u are gonna need alot of jack stands and jacks to do this job.

Dec 18, 2009 | 2002 Cadillac Eldorado

1 Answer

'99 cadillac eldorado, Northstar engine w/AC problem


Have you unhooked the battery since you put the freon in? If not, do it.

Jul 04, 2009 | 1999 Cadillac Eldorado

1 Answer

Strange clipping sound coming from front right side. where are the cvs joints could it be that? or the drive shaft? it's a touring sedan edition.


It sounds like the CV joint gone bad. Usually when you look underneath the car at the axle that comes out of the inside of the wheel, you will see an rubber boot that looks like an accordion. That boot will be separated with grease sprayed everywhere. That is sure indication that the joint is your problem.

Jun 28, 2009 | 1994 Cadillac Eldorado

1 Answer

Can i reset my ac code? 1999 cadillac eldorado


Hi, follow this step for clear the a/c codes on your cadillac el dorado 1999.
I Hope you will solve your problem with this instruction page, thanks for using fixya.1736984.jpg

Jul 07, 2008 | 1999 Cadillac Eldorado

Not finding what you are looking for?
1999 Cadillac Eldorado Logo

Related Topics:

339 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...