Question about 2004 Dodge Ram 2500

Open Question

How do I replace steering box input shaft seal? 2004 Dodge Ram 2500 4wd

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: brake pad replacment on 2004 Dodge Ram 1500

Remove two bolts holding caliper on and pull up as hard as you can on the caliper. Wiggling back and forth at the same time helps.

Posted on Aug 02, 2008

  • 5 Answers

SOURCE: Steering problem 1997 Dodge Ram

the half shaft does not need to go in a certain way, Just as long as you get it in all the way. when checking steering play to see where it is. It's best to leave the truck off. Turn ignition on but dont start to unlock steering column, Then look by driverside tire while your buddy just turns the wheel only the amount of free play it has. Just back and forth usually a few inchs. till it starts getting tight. "Look at the steering shaft and you will see it turning back and forth. Then Look at the output on the pitman arm. It should move back and forth with steering shaft. slower but at the same rate. If it does not. you need a gearbox. but read up because you can adjust some of them with a locknot and screw on top of box. If it's ok. look at the drag link. And down the line. eventually you'l find the problem. Any more Q e-mail me at gethuge8@yahoo.com
:)

Posted on Dec 14, 2008

BCally1
  • 133 Answers

SOURCE: rear pinion seal replacement

with a puller

Posted on Jan 13, 2009

fgainer
  • 54 Answers

SOURCE: 2004 dodge ram 1500 rear brake light out how to replace?

Open up the tail gate, you will see two torque screws on the inside beside the tail lights. take these out, this will free up the housing and you can change it from there.

Posted on Feb 01, 2009

  • 840 Answers

SOURCE: passanger side mirror replacement on 04 dodge ram 1500?

very easy take the mirror inside cap off if you can not get to the 3 bolts then you will have to take trim panel off to take trim panel off look for plastic caps take them out and unscrew them then pop out the bottom of the door and pop the sides out then lift up and out should be loose enough for the bolts now/ 10mm bolts 3 Please rate my response thank you very much

Posted on Feb 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dodge steering gear box. How to identify the upper and lower seals to the Pittmann arm? Which way are they to be turned?


Im a little unclear about what your discribeing . But i think your asking witch side of the seal is up and witch is down. You need to look at the shaft that the seal is slideing over and the seal . The seal fits into a houseing and thats not going to leak . But the shaft that it seals againest will if the seal is upside down. In almost every case the side of the seal thats open has a grove that you can look inside of it and see a metal spring going around the inner lip of the seal goes to the inside of the compount . Look at the shape of the inner lip of the seals . And on a 2008 you shouldn't be haveing this problem its likely a front end problem that caused this or an oil leak in the power steering pump more likely the front end pitman arms are solid and vary strong as is the gear box Good luck

May 10, 2012 | 2008 Dodge Ram Pickup 1500

1 Answer

Steering fluid leak; oil covering steering gear box


if the leak is coming from the steering box there are usually only 3 places it can come from;most common place is the pitman shaft seal,which can be replaced.this is were the pitman arm of the steering connects to the steering box.another place is the steering box input shaft seal,this is were the steering colume connects to the steering box,which can be replace.the last place is the power steering hoses were they connect to the steering box.there are seals that seal the lines when screwed into the box which can also be replaced.so first you need to see exactly were the leak is coming from.rare occasions the steering box is porous which means the box will need replacing.a car of this age should have shown up long ago.you will have to clean the box off at the car wash then run the car and turn the steering wheel all the way to one side,this will build up pressure in the system to show up the leak quicker.

Apr 04, 2012 | 2000 Jeep Wrangler

1 Answer

How to install power steering geat seal kit on a 2001 Dodge ram 1500 3.9l


I will tell you that theres a good change this will not work. have tried this many times and when the seal leaks that means the shaft or components in the gearbox are worn and the new seal will not last. you are better off replacing the gearbox, unless you completely dissassembly the box and check all components and machine accordly but this is time consuming and the shaft may need replacing. i quess you can try the seal but cross your fingers maybe it will work.

Aug 29, 2011 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

I need a steering box diagram to replace seals in a 01 dodge ram 1500 4x4!


I suggest that you replace the box with a rebuilt unit. If the seals fail, usually there is excessive clearance and new seals will fail soon.

Jul 06, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

Leaking pitman arm seal at gear box


most of the good rebuild kits have the diagram in it there is not that much in there secter shaft worm gear + some seals and the parts are
not cheap you may be better off with a good used one with fresh seals

Jan 11, 2010 | 1996 Dodge Ram

1 Answer

The steering works fine but the input shaft seal is leaking. I need instructions on how to replace the seal.


Very carefully drill into the seal, after removing the circlip securing the seal in the box, with a 1/16" - 1/8" drill bit until you are through the seal. Then take a wood or sheet metal screw and thread it through the hole til the seal is forced up out of the gearbox. You can do this in the CJ by removing the steering shaft off the input shaft. Use a long (deep) socket to install the new one.

Nov 13, 2009 | 1983 Jeep CJ7

1 Answer

1999 dodge cummins 2500 front axel seals


you need to pull off wheels,brakes, rotor /unit hub bearing, both axles and intermediate shaft, as well as the vac disconnec ton the front axle tube. if only the right side leaks then only then only pull the right axle and intermediate shaft and vac disco. it is a trick with a miller tool to replace the seal. the left side seal is inside the diff and the carrier has to come out to replace it. pete

Jun 09, 2009 | 2004 Dodge Ram 2500

2 Answers

RACK AND PINON DODGE RAM 1500 2005


if you have a leak from the back of the rack your sector shaft seal is defective. to replace it you need to remove the rack and do it on the bench.remove the locking nut and pull the seal from inside.if you are a rooky replace the rack with a rebuild one. good luck.

Jan 27, 2009 | 2004 Dodge Ram 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

372 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...