Question about 1995 Eagle Talon

1 Answer

There is knocking in the engine that has 104K miles. Some say engine bearing spun and others think Timing jumped. Can't drive t all. An Ideas? Thanks Patrick!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Timing jumps a backfire is heard. deep knocking is a main bearing to the crankshaft normallt the rear main bearing goes first

Posted on Sep 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 olds.intruge 3.5 engine


loud knocking internal lower part of engine usually means [ rod knock ] --bad wrist pin -spun bearing -or piston ring]s] --that the worst other can be timing failure --or component failure --you need to isolate the noise and diagnose from there

Oct 01, 2016 | Cars & Trucks

2 Answers

Where is the oil pump on a 318,1992 dodge ram 1500


Inside the oil pan. Not an easy job. Just a note... Probably not the pump. Probably is the main and rod bearings on the crankshaft. Pull the engine. If really high miles rebuild the engine or replace it. If low miles (like 100,000), replace the crank and bearings. Unless a bearing has spun. You would know because there would be a constant knocking in the engine lower end.

Jan 04, 2015 | Cars & Trucks

1 Answer

Cylender loaded with gas engine making knoking noise


Maybe a spun bearing or an oil pump not turning any more.

Jan 10, 2014 | 2002 Chrysler Sebring

2 Answers

Oil presure gauge went to zero and computer said low oil presure! I then heard a loud knocking coming from engine! I check level of engine oil and its full, what do you think it is?


You didn't state the mileage (would help with diagnosis) But unfortunately you have suffered major engine damage. And that would depend if the knocking you hear is steady at engine idle or only knocks when reving the engine . For some reason the oil pressure did fall to zero, most likely due to bearing wear but again depends on mileage. If knocks constant at idle it is a spun main bearing, if knocks only while reving engine it is a spun connecting rod bearing. Either require an engine overhaul. Or engine swap, Once again it depends on how many miles you have the engine to determine if its wise to rebuild it or replace it. I hope this answers your Q.....

Jul 28, 2011 | 2003 GMC Sierra 1500

2 Answers

Engine Knocking


Knocking can be caused by

1) pre-detonation on hills due to carbon build up in the engine or too low of an octane gas used.
2) worn or spun out bearings in the camshaft or crankshaft that has connector rods for the pistons attached.
3) bad bearings in a belt driven accessory.

.

Jan 25, 2011 | 1996 Mercedes-Benz C-Class

1 Answer

My 1996 gmc jimmy is making loud knocking noise when I start it and shaking and sounds like it will cut off at any moment and the engine check light is on I know I have to take it in but you give me some...


Spun bearing = time for engine rebuilt. Sounds like your engine spun a crank shaft bearing or connecting rod pin is loose or worn out. If your lucky, it may just be a worn distributor gear that is causing your knocking due to bad timing.
Good luck and try not to run the engine with the knocking, it may be a simple fix that will lead to a major problem.
Thank you for using fixya and is the engine oil level right where it suppose to be???

Apr 09, 2010 | 1996 GMC Jimmy

3 Answers

Knocking noise when i accelerate


CHECK ALL DRIVE BELT ACCESSORIES LIKE ALTERNATOR - AIR CONDITIONER COMPRESSOR AND CRANKSHAFT PULLEY.I HAVE SEEN A LOOSE OR BAD TRANSMISSION MOUNT CAUSE KNOCKING NOISE IF ENGINE ACCELERATED.

Mar 01, 2010 | 1997 Honda Civic

1 Answer

While driving 2003 santa feengine seemed to have lost acceleration suddenly and engine is making verry loud "knocking" noise. any ideas on where to start looking for noise found engines have hydraulic...


well theres a few places
first would be conecting rods
knock knock
whos there
as the conecting rods blow through the block

might have spun the timing belt a noch

Jan 05, 2010 | 2001 Hyundai Santa Fe

2 Answers

My 2002 honda civic has a steady clicking noise that goes faster on acceleration. The noise is audible though just when idling as well. Any ideas?


Needs more oil or you spun a bearing. Also could knocking lifter. Try some engine restore if your oil is at the proper level. If that doesnt work it will be spun bearing or bad rocker. Have it checked out by local mechanic to be for certain.

Sep 15, 2009 | 2002 Honda Civic

1 Answer

1996 Mercury Tracer with sudden loud engine knock


Was the engine overheated when it shut down on the highway? If so, it probably seized due to a stuck bearing, when you restarted the engine, the bearing spun and now you likely hear a connecting rod knocking around in the engine without bearings. This will mean you need a new engine.
If the engine didn't overheat, then it's possible that a valve seat in the cylinder head fell out of place and is now banging around inside a combustion chamber destroying the engine and you will likely need a new one. This was a very common problem on one of the Ford based 4 cylinder engines, it depends which one you have. The major offender was a 2.0 litre.
Another possibility, the timing belt has jumped and the pistons are now hitting the valves, causing the engine to run rough. This will either require a major repair or a new engine.

Mar 11, 2009 | 1996 Mercury Tracer

Not finding what you are looking for?
1995 Eagle Talon Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Eagle Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Stewart Dibbs

Level 2 Expert

267 Answers

Are you an Eagle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...