Question about 2007 Toyota Tundra

1 Answer

Serpentine Belt routing diagram for 2007 Toyota tundra and which pulley is the tension pulley

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Installing fanbelt on 2007 Toyota Tundra 5.7

Posted on Oct 31, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

HDo I remove and install an idler pulley on a 2005 Toyota Camry?


How to replace drive belt tensioner Toyota Camry - YouTube

? 4:26
https://www.youtube.com/watch?v=gfSJvN-CE2E
Feb 22, 2013 - Uploaded by Fix It Angel
2002 2003 2004 2005 2006 2007 2008 2009 Toyota Camry. Engine, 4 cylinder, 2.4L, 2AZ-FE. 2004 Toyota ...

Idler Pulley, How to replace (EASY and CHEAP) - YouTube

? 4:56
https://www.youtube.com/watch?v=axAltpW8wR4
Nov 2, 2013 - Uploaded by ChrisFix
Idler pulley squeak? Learn how to fix a squeaky pulley in your car. The serpentine belt in your car powers the ...

2007 Camry Serpentine Belt Replace - 4 Cyl, 2.4 liter ...

? 4:21
https://www.youtube.com/watch?v=ejhyCrh96a8
Jan 13, 2013 - Uploaded by Flyin Brian
I show you step-by step how to get the old belt off and install a new ... ... Water pump replacement 2007 Toyota ...


Jan 27, 2016 | Toyota Cars & Trucks

1 Answer

Serpentine belt diagram for a 2003 Chevy unpalatable 4.3


Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

  • 2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.
  • 3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.
  • 4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.
  • 5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.
  • 6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

  • Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

    Sep 21, 2011 | 2003 Chevrolet Impala

    2 Answers

    Need a diagram for a 99 toyota corolla serpentine belt


    • Here is the serpentine diagram for a 1999 Toyota Corolla with and without AC.

    ironfist109_31.gif


    • Thank you for using FixYa

    Regards, Tony

    Jun 19, 2011 | Toyota Corolla Cars & Trucks

    1 Answer

    How do you change a 07 toyota tundra serentine belt


    Insert a ratchet or breaker-bar drive (end of bar) into the square hole in the tensioner / idler pulley mount. Move the tensioner mount in whatever direction is required to release tension on the belt. You will then be able to remove the belt. Install new belt similarly -- there should be a routing diagram under the hood for the belt -- if not, it would be a good idea to diagram it yourself before you remove the old one.

    Charlie

    Jan 09, 2011 | 2007 Toyota Tundra

    1 Answer

    I need to replace the serpentine belt on my car. How do I do that?


    These instructions will help you . and also the picture below will help you more.
    1
    Locate the belt-routing diagram, printed on the fan shroud or possibly applied to the underside of the hood. This diagram shows you how to properly route the new belt, as well as identifying the location of the various pulleys, including the serpentine belt tensioner.
    2
    Move the belt tensioner off the Sable's belt using the serpentine belt tool. The tool connects to the side of the tensioner's arm and essentially acts as a handle for use in moving the tensioner. You can purchase a serpentine belt tool at most auto-part retailers.
    3
    Slip the belt away from the tensioner with your free hand and release the pressure on the tensioner with the tool. Pull the belt off the rest of the pulleys by hand and then remove it from the engine well.
    4
    Grab the old belt and new belt with one hand and put your foot through the other end of the belts. Stretch them both to their full length and check to ensure their both the same size. The old belt may have up to one-inch of extra length due to normal stretching that occurs during the belt's service life.
    5
    Wind the new belt, rib side to the pulley, around the crankshaft pulley. Consult the routing diagram and route the belt to the next pulley on the diagram. Continue to route and then check the diagram until you have the belt wound around every pulley except the belt tensioner pulley.
    6
    Double check to make sure the belt routes exactly as shown on the diagram and then move the tensioner aside once more so you can route the belt over the tensioner pulley as shown in the diagram. Move the tensioner back into place slowly and remove the tool.

    Good luck

    tgv1501_23.jpg




    Jan 03, 2011 | 1996 Mercury Sable

    2 Answers

    Change serpentine belt on 06 sienna


    1. 1 Check to ensure the Sienna's engine is cold, then make sure the Sienna is in park, the ignition is in the off position and the key is removed from the ignition to prevent any possibility of the engine engaging during the serpentine belt replacement.
    2. 2 Open the hood and locate the serpentine belt routing diagram sticker on the side of the engine casing. Study it for a moment before removing the existing belt. It is essential the new belt be installed exactly as the diagram indicates.
    3. 3 Find the tensioner pulley, the main pulley that controls the serpentine belt, and fit a 1/2-inch socket wrench over the self-tensioner on the outside of the pulley.
    4. 4 Pull the wrench to the left to move the pulley forward, which loosens the belt, then remove the belt.
    5. 5 Compare the old serpentine belt with the new, replacement belt for length, width and number of grooves on the belt's underside. Be certain the replacement belt is the right part.
    6. 6 Fit the new belt on to each pulley according to the serpentine belt routing diagram on the manufacturer's sticker, or according to the drawing made prior to removing the old belt. Fit the new belt on to the tensioner pulley last, again applying pressure on the pulley's self-tensioner with the half-inch socket wrench to loosen the pulley.
    7. 7 Release the pressure on the self tensioner and allow the tensioner pulley to ease back into place, thereby tightening the new serpentine belt with the appropriate tension.
    8. 8 Remove the wrench and close the hood.
    Thank you and good luck,
    Lee

    Aug 26, 2010 | 2006 Toyota Sienna

    1 Answer

    I need a diagram routing for a serpentine belt in a jetta 2007


    The diagram routing for a serpentine belt in a VW Jetta 2007, 2,0 FSI engine.
    See picture below:

    0a3cd9e.jpg
    CS = Crankshaft
    F = Fan pulley
    Gen = Alternator
    T = Tensioner
    AC = Air Conditioning
    PAS = Power Assisted Steering
    WP = Water Pump

    Aug 08, 2010 | Volkswagen Jetta Cars & Trucks

    1 Answer

    How to change serpentine belt, 2004 Toyota Tundra


    locate tensioner pulley; release tension from belt; remove belt; make sure not to forget how the belt is routed; route belt around all pulleys but tensioner; put tension on tensioner pulley; route belt over tensioner pulley

    Oct 03, 2009 | 2004 Toyota Tundra

    1 Answer

    How do i change a serpentine belt for a 2007


    Drive Belt: Service and Repair
    DRIVE BELT

    Components
    43931e7.jpg


    REMOVAL
    1. REMOVE V-BANK COVER SUB-ASSEMBLY
    2. REMOVE NO. 1 ENGINE UNDER COVER

    4cff58f.jpg



    3. REMOVE FAN AND GENERATOR V BELT
    (a) While turning the belt tensioner counterclockwise, align the service hole for the belt tensioner and the belt tensioner fixing position, and
    then insert a bar of [diameter]5 mm (0.197 in.) into the service hole to fix the belt tensioner in place.
    HINT: The pulley bolt for the belt tensioner has a left-hand thread.
    (b) Remove the V belt.



    1. INSTALL FAN AND GENERATOR V BELT
    (a) Set the V belt onto every part.
    (b) While turning the belt tensioner counterclockwise, remove the pin.
    NOTICE: Make sure that the V belt is properly set to each pulley.
    (c) After installing the belt, check that it fits properly in the ribbed grooves.
    HINT: Make sure to check by hand that the belt has not slipped out of the grooves on the bottom of the pulley.
    2. INSTALL NO. 1 ENGINE UNDER COVER
    3. INSTALL V-BANK COVER SUB-ASSEMBLY

    c0b77ac.jpg

    Sep 28, 2009 | 2007 Toyota Tundra

    Not finding what you are looking for?
    Cars & Trucks Logo

    3,882 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    75807 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22133 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8172 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...