Question about 1998 Oldsmobile Intrigue

Open Question

How do you change a master cylinder on a 1998 Oldsmobile Intrigue

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: 1998 olds intrigue trouble code p0171

I have a dianogstic machine and the code you were given indicates that the system is too lean. (Bank 1) Were you go from here i'm not too sure. Steve

Posted on Oct 01, 2008

  • 5 Answers

SOURCE: One side front wheel bearings need changed How do I know which?

It may be your alignment but if it is wheel bearings jack up the front of the vehicle and try to rock or shake the wheels by hand if there is play or it does move it is your wheel bearings

Posted on Mar 30, 2009

SOURCE: parts need to change to preform a tune-up

usually spark plug ,rotor..under distributor cap..maybe new distributor cap depending on the wear on the inside contacts fuel filter..hope this helps

Posted on Apr 15, 2009

tepfy
  • 319 Answers

SOURCE: how do i install a 1998 oldsmobile intrigue water pump?

you need to go buy a Chilton. There is a litle more to it than telling you a couple of things on a web page. Also if your car has a 4 cylinder and you are replacing the water pump, something they don't tell you is you have to replace the timming belt also. If you don't you will be replacing them both again in a couple of months.

tepfy

Posted on May 03, 2009

  • 1986 Answers

SOURCE: i have an 1998 Oldsmobile

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then pull back the weather seal and you will be able to put it back on the track. You will most likely need to buy some clips to secure it back on

Posted on Oct 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heat stopped working in 2000 Oldsmobile intrigue. What could it be? I can't find the blower or HVAC relay and all fuses are good


fuse for the heater fan on a 2000 Oldsmobile Intrigue located. Passenger side, open the front door. On the side of the dash. These videos should help you locate them.
Interior Fuse Box Location 1998 2002 Oldsmobile Intrigue 1998 Oldsmobile...

Nov 17, 2016 | 2000 Oldsmobile Intrigue

1 Answer

1998 Oldsmobile Intrigue Logo Print Email Problem with 1998 Oldsmobile Intrigue how do i troubleshhoot a random misfire code for intrique 1998 with flashing service engine light new tune up or...


Best to run it to autozone let them scan it with their scanner to tell you which plug is misfiring the will do this free. and it will tell you exactly what is the troubled cylinder.Remember to rate my solution this is how i earn my achievements also testimonial Thanks much in advance.

Apr 22, 2012 | 1998 Oldsmobile Intrigue

1 Answer

Where are the O2 sensors located on 1998 Olds Intrigue?


Ther are two sensors on this car if it has a 4 cylinder engine, these sensors are screwed into the exhaust system pipes, theres one before the cat converter and one after converter,. you just unplug connector and use wrench to loosen and remove.

Aug 28, 2010 | 1998 Oldsmobile Intrigue

1 Answer

1998 Oldsmobile Intrigue


It is located on the back wall right under the alternator and idle pulley! hope this helps and you will need a funnel!

Jul 05, 2009 | 1998 Oldsmobile Intrigue

2 Answers

I need a spark wire diagram for a 1998 3.8 olds intrigue


Viewing the front of the engine, going from the front to the back, the left side cylinders are 2, 4, and 6.
The right side cylinders are 1, 3, and 5.
The firing order is 1-6-5-4-3-2

May 19, 2009 | 1998 Oldsmobile Intrigue

1 Answer

How do i install a 1998 oldsmobile intrigue water pump?


you need to go buy a Chilton. There is a litle more to it than telling you a couple of things on a web page. Also if your car has a 4 cylinder and you are replacing the water pump, something they don't tell you is you have to replace the timming belt also. If you don't you will be replacing them both again in a couple of months.

tepfy

Apr 25, 2009 | 1998 Oldsmobile Intrigue

Not finding what you are looking for?
1998 Oldsmobile Intrigue Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7689 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...