Question about 1994 Oldsmobile Ninety Eight Regency

Open Question

How to replace timing chain cover on a 94 oldsmobile 98 3.8 motor

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 66 Answers

SOURCE: replacement time harmonic balancer 1994 olds 98

not sure abot book time. actual time is about 45 minutes with proper tools

Posted on Jun 29, 2009

c17hydro
  • 2984 Answers

SOURCE: Timing Chain Cover, Chain, Sprockets, replacement

2.2L VIN 4 To Remove:

  1. Remove or disconnect the following:
    • Drive belt.
    • Drive belt tensioner.
    • Alternator.
    • Power steering pump. Place the pump aside with the lines attached.
  2. Lift the vehicle.
  3. Remove or disconnect the following:
    • Oil pan.
    • Crankshaft pulley and hub.
    • Timing cover bolts.
    • Timing cover. If necessary, tap with a rubber mallet to loosen the cover.
  4. Clean the mating surfaces.
To Install:
  1. Install or connect the following:
    • Timing cover gasket.
    • Timing cover and the bolts. Tighten the bolts to 11 Nm (97 in. lbs.).
    • Crankshaft pulley hub and the crankshaft pulley.
    • Oil pan.
  2. Lower the vehicle.
  3. Install or connect the following:
    • Power steering pump.
    • Alternator.
    • Drive belt tensioner.
    • Drive belt.

Posted on Aug 30, 2009

  • 753 Answers

SOURCE: I need a diagram for a 94 oldsmobile cutlass

There is a dot on each of the gears one on the large cam gear and one on the small crank gear.The crank gear dot on the teeth of the gear should point to the 12oclock postion straight up then the one on the cam gear point sin the 6 O clock position so the dots meet each other then you put the chain on the cam gear then around the crank gear then bolt on the cam gear the dots should still be lined up with each other.this puts the engine in the #4 firing postion

Posted on Oct 06, 2009

  • 58 Answers

SOURCE: I wanna change my engine in my 95 blazer it has

you will have to swap intakes dist. timing cover and harmonic balancer so you have the mounting whole and reluctor ring for your ckp crank postion sensor. cmp cam postion sensor is in the distributor,

Posted on Mar 10, 2010

  • 409 Answers

SOURCE: replace timing chain cover on 1999 chevy van 2500

should be able to get the cover off with the engine in the frame. Just take out the grille and header support, then disassemble the front of the engine. If you are dead set on removing the engine, she comes out the front after taking everything out of the way.

Posted on Mar 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i correctly replace a timing chain and timing cover on a 98 dodge ram 1500


Youtube is usually the best option as there are loads of examples of timing chain removal and replacement posted by mechanics.

Aug 03, 2014 | 1998 Dodge Ram 1500 4WD

1 Answer

I need a diagram for a 99 explorer timing chain 4.0 4x4


it needs a special tool from ford the kit is 500 i think. used engine is cheap u can also put a 98 or 97 motor if its cheaper change the valve cover and intake also fly wheel exhaust manifold from the bad motor. i have done it works every time.

Dec 02, 2012 | Cars & Trucks

3 Answers

1995 Olds Silhouette rattled badly, died while running


I think you had better have a local shop inspect this for a failed engine connecting rod.

Aug 23, 2012 | Oldsmobile Silhouette Cars & Trucks

1 Answer

Does the 1997 Oldsmobile 1988 6 cylinder have a timing chain or timing belt? When does it need to be changed?


It has a timing chain. A chain will typically last the life of the motor. The only time it really needs to be replaced is if it is making noise. The only time I replace them is if I have the front cover off to repair a leak. Since pulling the front cover is most of the labor its not a bad idea to replace the chain as long as it is right there.

The other exception is if the engine is starting to approach some really high mileage. Say around the 200,000 mile or more range. The old timing chain doesn't owe you anything and it certainly can't hurt to install a new one.

Feb 10, 2011 | 1997 Oldsmobile 88

1 Answer

I need to know how to replace timing chain on olds 3.5 twin cam motor.


Take every thing off the front of engine, until you have access to the timing chain cover . This is a very large task. If you are not a mechanic be careful you have to make sure #1 cylinder is top dead center before removing gears and chain.

Oct 27, 2010 | 2002 Oldsmobile Aurora

1 Answer

How do I instal a timing belt on a Delta 88 Oldsmobile?


You don't list the year but i'm fairly certain your Oldsmobile has a timing chain, not a belt. A timing chain doesn't have a regular service interval and should only be changed if it's suspect of having excessive wear or other problem that requires replacement. You can tell if you have a chain or a belt by looking at the timing cover. If it's shallow and metal, it's a chain. If it's about 2-3" deep and plastic it's a belt.

Aug 12, 2010 | Oldsmobile Delta 88 Cars & Trucks

1 Answer

Changing an engine belt, but motor mounts in the way. how do i take the old belt out


Get a floor jack.Position the jack with a block of wood on top right under oil pan.Jack the jack untill it barely touches the bottom of pan.Remove mount and timing chain cover to replace timing belt.Make sure you allign timing marks before you remove belt.Make sure timing chain tensioner is working properly.Reverse procedre to replace.Good luck.

Jun 11, 2010 | 1993 Oldsmobile Cutlass Ciera

1 Answer

Gear noise inside motor


Probably the timing chain getting loose and rubbing the timing cover. Time to replace the timing chain!!

Oct 10, 2009 | 1987 Oldsmobile Ciera

1 Answer

For a 94 chrysler town & country, where is and do


the timing chanin is behind the timing chain cover on the passenger side of the engine. u must remove the crank pulley to remove the cover.

no you do not have to remove the engine to service the timing chain

Apr 12, 2009 | 1994 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

164 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7689 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...