Question about 1991 GMC Sonoma

1 Answer

REPLACING DOME LIGHT - DOES IT MATTER WHAT SIDE THE ORANGE WIRE GOES ON - OR THE WHITE WIRE AND AT WHAT ANGLE???

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 560 Answers

No it doesn't matter...the orange is +12vdc and the white is the "momentary" ground that is made with the opening of the doors , the switch, if one is up there, and the dome light switch on the dash instrument control.

Posted on Sep 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dome light now working on a 2011 enclave. i looked at dome switch. what do i need to do?


Hello! If you have a multimeter and a little experience using it I'll send a very easy test procedure...If you do not have a meter send a comment...Remove the lens cover from the dome light...You'll see two wires...Orange and Black...Set the meter to read 12 volts...With the drivers door open Read across the Orange and Black wires with the dome switch off...If you do not read 12 volts the door switch is bad...
If you do read 12 volts turn the dome switch to on...if the bulb is good...The dome light switch is defective...But I doubt you will read 12 volts on the Orange wire to ground...More then likely the door switch is defective...Gently pry the door panel off...Use a screw driver with shrink tubing over the tip...
The wire colors on the switch are Tan and Yellow...It is a part of the latch assembly...You can replace it yourself, however since it's a 2011 its a warranty item...On the difficulty scale of 1 to 10 replacing the door switch is a 4...Guru.......Saailer

Feb 16, 2011 | Buick Enclave Cars & Trucks

2 Answers

How to disarm or reset an alarm system for a 1996 Jeep Cherokee?


Hope this helps:- Factory Disarm Purple/Yellow (-) Driver's Kick Panel Black Connector at ECM -slice into this wire, & wire it to ground, this disables the alarm.
Cavity/Fuse Diagram (1996 Grand Cherokee, passenger side kick plate to find, Owner's Manual pgs 205-206): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

Row 1: 1-6 (left to right) Row 2: 7-12 Row 3: 13-18 Row 4: 19-22
1996 Jeep Grand Cherokee Fuse Panel (Passenger Side kick panel) Reply

CAVITY FUSE DESCRIPTION 1 -10 amp (RED) Radio 2 -15 amp (Lt Blue) Cigarette Lighter 3 -10 amp (RED) Rear Washer Switch, Body Controller 4 -10 amp (RED) Airbag 5 -10 amp (RED) Lamp Out Module, Overdrive Switch, OBD II 6 -15 amp (Lt Blue) Vehicle Information Center/Graphic Display Module Park & Side Lamps, Overhead Console Lighted Visor, Automatic Dimming Mirror 7 -20 amp (Yellow) Body Amp, Cluster, Body Controller 8 -20 amp (Yellow) Rear Wiper Motor, Flipper Glass Solenoid, Cargo Lamp, Trailer Tow 9 -15 amp (Lt Blue) Brake Switch 10- 10 amp (RED) Rear Window Defroster 11 -10 amp (RED) ABS Module 12 -10 amp (RED) Heater-Ventilation-A/C Control & Recirculation Motor 13 -15 amp (Lt Blue) Hazard Switch, Turn Signal Switch 14 -15 amp (Lt Blue) Spare 15 -15 amp (Lt Blue) Spare 16 -10 amp (RED) Right & Left Courtesy Lamp, Glove Box Lamp, Halo Lamp Cargo Lamp, Underhood Lamp, Dome/Read Lamp Right & Left Visor, Automatic Dimming Mirror 17 -15 amp (Lt Blue) Radio Illumination, Tail Lamp, Graphic Display Module, Park & Side Lamps, Headlamp Switch, Body Controller 18 -20 amp (Yellow) Spare 19 -15 amp (Lt Blue) Passing Light 20 -15 amp (Lt Blue) Radio, Heater-Ventilation-A/C, Vehicle Information Center 21 -15 amp (Lt Blue) Power Outlet 22 -10 amp (Blue) Airbag Module -------------------------------------------------------------------------------------
1996 Jeep Grand Cherokee Alarm, Remote Starter, Keyless Entry Wiring Information Constant 12V+ Pink/Black Ignition Switch Harness Starter Yellow Ignition Switch Harness Ignition Dark Blue/Gray Ignition Switch Harness Ignition 2 Red/Black Ignition Switch Harness (for AC) Accessory Black/Orange Ignition Switch Harness Tach Gray/White Coil Brake Switch White/Tan Brake Switch Trunk Pin n/a Works with Dome Light Parking Lights Blue/Red (+) Left of Steering Column or Light Switch Head Lamp Tan/Black Light Switch Factory Disarm Purple/Yellow (-) Driver's Kick Panel Black Connector at ECM -slice into this wire, & wire it to ground, this disables the alarm. Door Trigger Yellow (-) Driver's Kick Panel see notes Door Lock 5/Wire in Driver's Inside Driver's Door Orange/Purple Lock Pink/Black Unlock Door Unlock and Passenger's Doors Inside Passenger's Door Black/White L Pink/Black Unlock Horn Wire Gray/Orange (-) Steering Column Windows Up LF=Light Blue, RF=Brown/White, LR=Blue/White, RR=Gray/Black Doors Windows Down LF=White, RF=Purple/White, LR=Red/Black, RR=Green/White
• Cruise Control Information • Stereo Information • View all Jeep Vehicles

Dec 18, 2010 | 1996 Jeep Grand Cherokee

2 Answers

I have a 1996 Jeep Cherokee and the heater vents dont work.I have tried to find a picture of the fuse panel i can read but i cant..When you swith it to vents it only comes out of the defrost.Where can i...


Hope this helps:
Cavity/Fuse Diagram (1996 Grand Cherokee, passenger side kick plate to find, Owner's Manual pgs 205-206): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

Row 1: 1-6 (left to right) Row 2: 7-12 Row 3: 13-18 Row 4: 19-22
1996 Jeep Grand Cherokee Fuse Panel (Passenger Side kick panel) Reply

CAVITY FUSE DESCRIPTION 1 -10 amp (RED) Radio 2 -15 amp (Lt Blue) Cigarette Lighter 3 -10 amp (RED) Rear Washer Switch, Body Controller 4 -10 amp (RED) Airbag 5 -10 amp (RED) Lamp Out Module, Overdrive Switch, OBD II 6 -15 amp (Lt Blue) Vehicle Information Center/Graphic Display Module Park & Side Lamps, Overhead Console Lighted Visor, Automatic Dimming Mirror 7 -20 amp (Yellow) Body Amp, Cluster, Body Controller 8 -20 amp (Yellow) Rear Wiper Motor, Flipper Glass Solenoid, Cargo Lamp, Trailer Tow 9 -15 amp (Lt Blue) Brake Switch 10- 10 amp (RED) Rear Window Defroster 11 -10 amp (RED) ABS Module 12 -10 amp (RED) Heater-Ventilation-A/C Control & Recirculation Motor 13 -15 amp (Lt Blue) Hazard Switch, Turn Signal Switch 14 -15 amp (Lt Blue) Spare 15 -15 amp (Lt Blue) Spare 16 -10 amp (RED) Right & Left Courtesy Lamp, Glove Box Lamp, Halo Lamp Cargo Lamp, Underhood Lamp, Dome/Read Lamp Right & Left Visor, Automatic Dimming Mirror 17 -15 amp (Lt Blue) Radio Illumination, Tail Lamp, Graphic Display Module, Park & Side Lamps, Headlamp Switch, Body Controller 18 -20 amp (Yellow) Spare 19 -15 amp (Lt Blue) Passing Light 20 -15 amp (Lt Blue) Radio, Heater-Ventilation-A/C, Vehicle Information Center 21 -15 amp (Lt Blue) Power Outlet 22 -10 amp (Blue) Airbag Module -------------------------------------------------------------------------------------
1996 Jeep Grand Cherokee Alarm, Remote Starter, Keyless Entry Wiring Information Constant 12V+ Pink/Black Ignition Switch Harness Starter Yellow Ignition Switch Harness Ignition Dark Blue/Gray Ignition Switch Harness Ignition 2 Red/Black Ignition Switch Harness (for AC) Accessory Black/Orange Ignition Switch Harness Tach Gray/White Coil Brake Switch White/Tan Brake Switch Trunk Pin n/a Works with Dome Light Parking Lights Blue/Red (+) Left of Steering Column or Light Switch Head Lamp Tan/Black Light Switch Factory Disarm Purple/Yellow (-) Driver's Kick Panel Black Connector at ECM Door Trigger Yellow (-) Driver's Kick Panel see notes Door Lock 5/Wire in Driver's Inside Driver's Door Orange/Purple Lock Pink/Black Unlock Door Unlock and Passenger's Doors Inside Passenger's Door Black/White L Pink/Black Unlock Horn Wire Gray/Orange (-) Steering Column Windows Up LF=Light Blue, RF=Brown/White, LR=Blue/White, RR=Gray/Black Doors Windows Down LF=White, RF=Purple/White, LR=Red/Black, RR=Green/White
• Cruise Control Information • Stereo Information • View all Jeep Vehiclesairconman.jpg

Dec 16, 2010 | 1996 Jeep Grand Cherokee

3 Answers

Car started an hour ago now wont turn over security light in dash came on and stays on


if the security light is on then it is the VATS system. the ignition switch is fine still.

Aug 15, 2010 | 1995 Chevrolet Camaro

1 Answer

1959 pontiac 2 door bonneville. how do you hook up the wiring for the dome light? two wires coming down from the light. driver side door switch has two terminals. pass side door switch has one terminal.???


Negative from the dome light to one terminal on the door jab,and the other terminal,hook to,and run to the other door jam on passengers side.The hot wire from the dome light goes to the hot side on the fuse box.A additional light switch can be installed,to turn the dome light on from inside the car,by running a ground to the switch,and from the switch to the ground side of the dome light.

Nov 13, 2009 | 1978 Pontiac Bonneville

1 Answer

Need brake circuit diagram for 1991 chrysler new yorker


Hi,
1991 Chrysler New Yorker Auto Security Wiring Diagram
Battery Constant 12v+ Positive Wire (+): Red and Pink
Battery Constant 12v+ Positive Wire Location: Ignition Switch Harness

Starter Positive Wire (+): Yellow
Starter Positive Wire Location: Ignition Switch Harness

Ignition Positive Wire (+): Dark Blue
Ignition Positive Wire Location: Ignition Switch Harness

Accessory Positive Wire (+): Black/Orange
Accessory Positive Wire Location: Ignition Switch Harness

Parking Light Positive Wire (+): Black/Yellow
Parking Light Positive Wire Location: In Drivers Kick Panel

Power Door Lock Positive Wire (+): Orange/White Or Orange/Violet
Power Door Lock Positive Wire Location: In Drivers Kick Panel

Power Door Unlock Positive Wire (+): Pink/Violet
Power Door Unlock Positive Wire Location: In Drivers Kick Panel

Door Trigger Negative Wire (-): Yellow
Door Trigger Negative Wire Location: In Drivers Kick Panel

Dome light Supervision Wire: Use Door Trigger (Requires Relay)
Dome light Supervision Wire Location: N/A

Trunk Release Positive Wire (+): Black/White (Requires Relay)
Trunk Release Positive Wire Location: At Trunk Release Switch

Horn Negative Wire (-): Black/Red
Horn Negative Wire Location: At Relay In Fuse box

Tachometer Wire Negative Wire (-): Black/Gray
Tachometer Wire Negative Wire Location: At Ignition Coil

Brake Light Positive Wire (+): White
Brake Light Positive Wire Location: At Switch above Brake Pedal

Factory Alarm Disarm Wire (-): Light Green/Orange
Factory Alarm Disarm Wire Location: In Drivers Kick Panel

Factory Anti-Theft System: N/A
Factory Anti-Theft System Location: N/A


Thank You for contacting Fixya.com

Aug 03, 2009 | 1991 Chrysler New Yorker

1 Answer

1997 3rd brake cargo light


white wire makes the light come on with dome lights, orange wire should be constant power, black is ground and blue w/white should go directly to the brake light switch, both white should be the same connection if problems let me know

Feb 16, 2009 | 1997 Chevrolet C1500

1 Answer

Windows & locks not operating


TRY REPLACING ONE OF THE CIRCUT FUSES UNDER THE HOOD , IT IS A 50 AMP THEN THE DOME LIGHT SHOULD WORK, HOWEVER HAVE NO IDEA ABOUT THE WINDOWS AM HAVING THE SAME ISSUE , WITH THE WINDOWS.

Feb 13, 2009 | 2004 Jeep Grand Cherokee

1 Answer

Replaced multiswitch in 2000 chevy s10 blazer and now the car won


at the base of the steering column there a orange and white wires these two wires come from the ing switch, you will see the connector that they go to disconnect that take a ohm meter, take the leads one lead to one wire the other lead to the other there should be res, if there is not, try a different setting . take your ing key on the the key you will see a chip take two leads from your meter and either side of the chip place the leads you will see a res reading, you should see the same at the orange and white wires . if you do not replace the ing switch the switch will come with these wires. replacing the switch takes a couple specail tools good luck and let me know how it gose

Dec 22, 2008 | 2000 Chevrolet Blazer

2 Answers

Dome light does not come on when doors open, but does when dim switch is rotated. The dome light bypass button has no effect on it.


All the door switches use the same wiring harness. It's an orange and a white wire. There is a switch on the dash to turn the dome and wheel lights off. If the lights come on with the dimmer, the whole harness is OK, so now check to see if that switch is turned off... or bad

Aug 09, 2008 | 1998 GMC Safari

Not finding what you are looking for?
1991 GMC Sonoma Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...