Question about 1994 Nissan Quest

1 Answer

1994 mercury villager i need to change the harmonic balancer

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 4,369 Answers
Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I REMOVED THE DISTRIBUTER CAP AND AFTER I PUT IT BACK THE CAR REFUSED TO START .


Are all the wires going to the right cylinder? if yes....Did you mark the gearing/rotor location before removing? You may have thrown off the timing for the distributor. If this is the case, Remove the distributor and set the engine to TDC (top dead center). This can be done by spinning the crankshaft pulley/harmonic balancer twice clockwise until the marking on the pulley and timing cover is set to "0/Zero" Once set at TDC, set the distributor (cap must be removed) to TDC/Cylinder 1.

Nov 08, 2012 | 1994 Mercury Villager

2 Answers

How do you change the Harmonic balancer on 1994 Toyota tercel


no
just the harmonic balancer the bolt is tensioned to 112 ft/lb so get a1/2 " impact wrench as that will undo the bolt without the need to hold the crankshaft
may need a harmonic balancer puller but with that tension
the pulley should slip of the shaft with a bit of effort
to get space to run the impact gun , you may have to remove the radiator

Nov 20, 2017 | 1994 Toyota Tercel

1 Answer

How do I change a water pump for a 1994 mercury villager???


drain coolant first,take off serpentine belt loose 6 bolts on water pump take off water pump clean well,put new gasket than install new pump

Jan 10, 2010 | 1994 Mercury Villager

2 Answers

I need firing order for mercury villager 1994


it's 1-2-3-4-5-6.

#1 is on the passenger side rear and #3 & #5 are also on the back.

#2 is in front on passenger side. #4 & #6 are across the front.

go here for expert villager help.

http://groups.yahoo.com/group/villagerquest/

Jan 05, 2010 | 1994 Mercury Villager

1 Answer

1999 mercury villager 3.3, harmonic balancer bolt size


27 mm ...right handed(normal thread) which should torque to 160 ft/lbs

Jul 06, 2009 | 1999 Mercury Villager

1 Answer

Crankshaft sensor 1994 c220


Down by the harmonic balancer or behind the harmonic balancer. the harmonic balancer is the lowest pulley that your belt hooks to. there should be a wire connected to it.

Jan 04, 2009 | 1994 Mercedes-Benz C-Class

Not finding what you are looking for?
1994 Nissan Quest Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

79186 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...