Question about 1999 Ford Windstar

Open Question

On my 2000 windstar my front pump seal blew. I replaced the pump on my tanny and I think that it is strill leaking. any solutions on what it could be if not the seal

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 335 Answers

SOURCE: 2000 Windstar head light power door lock and front blinker

Check your fuses under hood and on dash. Some of these use two different fuses for rt. & lt. Look in you owners manual for the correct fuses to check. If it is a fuse problem, you will have to find out why the fuse was blown. Good luck

Posted on Apr 25, 2009

  • 8 Answers

SOURCE: Nissan Altima 2000 - Engine oil leaking problem.

replace the front oil seal. first i would clean the engine with purple power (degrease etc.) then look at the engine and make sure the leak is not coming from above like possibly the valve cover gasket or from the oil sending unit. try to tighten the bolts on the valve cover and even the oil pan. you never know, you may get lucky. i don't know where you are but front seals are cheap but the labor on the job is what costs you.

Posted on Jun 16, 2009

  • 173 Answers

SOURCE: I think its the relay in ford windstar

sound like you have a bad fuel pump no other reason to burn a fuse for fuel pump

Posted on Sep 23, 2009

  • 5763 Answers

SOURCE: 2000 ford windstar 3.8L Front heater has

what stopped? the air doesnt blow,if thats the case then replace the blowermotor resistor, its located on heater box on passengerside next to blower motor.hope this helps, let me know if this was the problem.

Posted on Dec 24, 2009

  • 10319 Answers

SOURCE: Ford Windstar 2000 y. leaking power steering

ford dealership parts department

Posted on Feb 11, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Hello,my 2000 odyssey leaks oil.guy said its front oil seal but im gonna need time belt,water pump,vtec valve and oil pan gasket.Do i really need all that just to change front seal? $400 for labor?

A leaking front seal will allow oil to get into the area where the timing belt is located. This will cause oil to get on the belt and can cause damage. Since the timing cover must be removed to access the front seal, it is recommended to replace the belt while you are in there. Also, the water pump is driven off the timing belt. Replacement of the water pump is always recommended when replacing the timing belt for two reasons. First, it is easily replaced at this time and it is good preventive maintenance. Secondly, the water pump bearing is under tension from the timing belt and develops a wear pattern. Replacement of the belt without replacing the pump will cause the new belt to wear the bearing in a different pattern, often causing leaking in a very short time after the replacement. This would then result in having to repeat all the labor again to replace the pump. It is easy to see that for $400.00 labor, you don't want to do that again in only 2-3 months. as far as the VTEC valve is concerned, I don't see a relationship to the oil leak. It could just be something else the mechanic found during the inspection. I can find nothing in the remove/replace procedures that requires replacement of the oil pan gasket. Again, maybe something additional that is needed from visual inspection, but not needed for the front seal.

Apr 03, 2016 | 2000 Honda Odyssey

2 Answers

97 ford windstar leaking transmission fluid

Possible leaks are 1. Transmission belly Pan gasket 2. Front pump/torque converter seal. 3. Transmission fluid cooler lines 4. Axle seals at right and left half shafts.

Feb 13, 2012 | 1997 Ford Windstar

1 Answer

Do you have to pull the engine out to replace the flywheel or do you just drop the trany and replace?

well you need to remove your trans, but not all the way move it back to where you have enough space to remove flyweel bolts, while you are there I recomend to replace your rear main seal, and if your tanny is leaking do your converter front pump seal, on this particular vehicle you have an easy access to trans bolts by removing dog house, usually this is done by a single person but if you have a body of yours that will lend a hand it will be a lot easier.

Jun 14, 2011 | 1992 Chevrolet G20

1 Answer

How can i fix a leak in transmission on a ford windstar 1999

transmitions usually leak in two places,, first is the pan, replacing the gasket should fix that ,, the second is the front seal ,, the transmition would need removed and the front seal replaced to fix that one

Apr 07, 2010 | 1999 Ford Windstar

1 Answer

Blew out new front trans seal

you might need to replace front pump bushing

Apr 02, 2010 | 1997 Ford F250 SuperCab

1 Answer

Looks like tranny fluid drip originates between oil pan and tranny bell housing extremely slow leak,all fluids are level,any input 2004 jeep wrangler x

well the only two places it can be leaking form are the front tanny seal or the pump seal if its minor leave it for now, because to fix it you have to remove the transmission.

Jan 19, 2010 | 2004 Jeep Wrangler

1 Answer

I have a 2002 ford windstar with 119506 miles on it and i was pulling out of an intersection and the van would not go it made a winding noise and when i put my foot down more it was barley moving could u...

it either blew the trans or more likely there is not fluid left in it. look for a huge leak such as a cooler line or front seal leak. that whine is bad,its the hydro pump in the trans burning up, dont slip the trans! itll take about 30 seconds of that and its fried

Aug 25, 2009 | 2002 Ford Windstar Cargo

1 Answer

Won't go into any gears except for reverse

Hi, if you have noticed any metal fragments at all, this will constitute a rebuild in this case. this trans was stressed to the max when the previous owner lost the fluid and blew the gear pack. i would just rebuild at this point. the seal is not the issue here. the pack is fried.

May 21, 2009 | 1995 Dodge Ram

2 Answers

Ford Windstar oil leak

Most possible oil leaks from valve cover rubber oil seal. Remove valve cover, inspect , clean surfaces, and replace with new rubber oil seal .
Good luck!
Thanks for using fixya.

Oct 19, 2008 | 2000 Ford Windstar

Not finding what you are looking for?
1999 Ford Windstar Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers


Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides