Question about 2000 Chrysler Sebring

Open Question

I have a 2000 Sebring JX, 2.5L. It will not crank. I've checked the start and battery they are both good. When I turn the key to the start position there is no clicking. I took the wire harness of the Powertrain Control Module (PCM) and jumped pin 31 to ground and when I turned the key to start position the starter turned the engine over but it would not start. The Auto Shutdown Relay (ASD) does not appear to be energizing. I can energize the relay when I jumper pin 67 on the PCM to ground. With everything put together and after turn the key to start position and then back to off position, the Idle Air Control Motor makes a humming sound and won't quit humming until I take fuse 5 out. Fuse 5 feeds the ASD relay and power to pin 46 of the PCM. I've also checked the Park-Neutral Position switch, pin 76 of the PCM reads 0.16v when in park and 12v when in gear. I don't get any codes. I don't know what the internal logic of the PCM is so I don't know what it takes for ASD relay to energize (pin 67) nor what it takes for engine starter motor relay to energize (pin 31). Any suggestions?

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1114 Answers

SOURCE: 94 dakota 5.2 - no spark - auto shut down relay not energized

Hello this is a feature to stop the engine and exhaust system from filling up with gas when spark is lost! years ago fuel would be delivered as usual and you Eng and converter would be full of gas real hazard back then!!!!now they built into computer when spark fails fuel automatically shuts off safety feature??? or not? so i would start to test coil this is a good place to start and if you have engine light on plug in OBD 2 scan tool to retreve the fault hope this helps you out and if you do not have a proper spark tester tool i would invest in one most auto parts stores usually carry them!!! $15-$30 dollars usually.John

Posted on Feb 15, 2009

bunnydawg
  • 5158 Answers

SOURCE: I went out to warm

First unhook the battery for about a half hour to reset the computer.
does that have anti-theft on it.
a remote starter ?
second either swap the relays for the starter and fuel pump or replace them outright.
when you bypass the relay to get it to crank... will it start ?

Robert

if that radio is of the anti-theft variety make sure you know the code and how to enter it

Posted on Dec 25, 2009

  • 1024 Answers

SOURCE: 99 town and country quit now even the warning lights dont come on

from ignition switch
key to run
black/orange power to fuse 11 and 12 in junction block and fuse 1 in power ditribution center
power to
black/white
dark blue
dark green/red
power all times
pink/black
red
pink
gray/black
check the maxi fuses

Posted on Mar 13, 2010

  • 1584 Answers

SOURCE: 94 Chrysler Town and Country won't start with key.

has it got an immobiliser / if so there is a fault there. If not an ignition switch itself.

Posted on Apr 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 chrysler sebring had battery light on yesterday. Door won't even lock with the key.


Most likely the battery, jumpstart it and confirm it runs after you take out the cables, if it doesn't, then its the altanator.-- cheers

Sep 29, 2016 | 2000 Chrysler Sebring

1 Answer

Reset computer for cluster and wipers on 2000 sebring jx after battery dissconect


Try resetting the body computer,with key away from vehicle disconnect battery for 3 minutes then reconnect it and wait 30 seconds then switch lights on then switch ign on 5 secs later, sure worth a try

Aug 25, 2016 | 2000 Chrysler Sebring JXi

2 Answers

2000 chrysler sebring will not turn over


Check starter,fuse,relay.check battery have to be 12.5V.

Apr 03, 2013 | 2000 Chrysler Sebring

2 Answers

1998 sebring wont crank over


If the engine will not crank, a mechanic would check for voltage at the battery, the starter, the neutral safety switch, and the key switch.
If the engine cranks but will not start, you would need to find out if you are dealing with a no spark or no fuel issue to proceed.

Aug 25, 2012 | 1998 Chrysler Sebring

1 Answer

2000 Sebring JXI wont start & when in reverse you can push the car forward or backward


https://s18.postimg.org/4m8krqjk9/sebring_starter.jpg

Click on the link for starter wiring. Not sure what's going on with your tranny? You can see in the diagram, the tranny module gets voltage from the crank position, ignition switch. You can also see the fuse, not only check the fuse, use a testlight and check voltage on fuse circuit.
Any testing, make sure functional parking brake is set and block the wheels. be safe. Safety is your responsibility.
Battery has a full charge and battery connections all good?

Jul 05, 2017 | 2000 Chrysler Sebring

1 Answer

My 1997 Chrysler Sebring JX quick running after coming to a stop at a stoplight I can here the fuel pump hum when the key it turned on cylinders have compression so I know the timing belt is on the crank...


You likely need a fuel pump because you hear the pump, but it is NOT pumping anything- like a well needs priming. Drop the tank and replace the pump.

Oct 30, 2011 | 1997 Chrysler Sebring

1 Answer

My 2000 Chrysler Sebring stops running. After a few minutes it will start again and run fine. This situation just started happenning a few months ago and is increasing in frequency


is the check engine light on??
i've done a few that had no light/codes.the most common problems are crank or cam sensor failures. really need to check when car stalls.
replacing crank sensor 6 mths ago & car has'nt had a problem. if you search these sensor on the sebring you'll find alot of info.

Jul 12, 2011 | 2000 Chrysler Sebring

2 Answers

Dear sirs, I have a 2000 Ford Explorer which won't start. All light in the dashboard turn on but the engine won't crank. We've tried to crank the engine direct from the battery and it cranked....


yea got get you more troubles
just check the alternator is charging well and no battery light on dashboard it indicate the bad alternator
monitor your battery if it got old and cannot hold the charge any more
you said when you used another one your car turned on

Jun 06, 2011 | 2000 Ford Explorer

Not finding what you are looking for?
2000 Chrysler Sebring Logo

Related Topics:

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...