Question about 1995 Ford Contour

Open Question

How to change 1995 ford contour GL crankshaft pulley

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

michigan man
  • 3533 Answers

SOURCE: 1995 Ford Contour GL, 4-Liter transmission problems

check the transmission fluid level first and also when was last time you had a tranny service new fluid and filter because the screen could be plugged and not allowing the fluid to get to the torque converter also have the catalytic converter checked out

Posted on Jan 12, 2009

  • 1 Answer

SOURCE: 97 ford contour gl, info on transmission pan filter installation?

trans filter can only be replaced by taking the trans apart. absolutely not worth it.

Posted on Apr 12, 2009

  • 1 Answer

SOURCE: do not know how to remove crankshaft pulley to replace timeing belt

Ignore smart a$$ comments.
Disconnect negative battery terminal.
Remove front right wheel.
Remove splash guard.
Place jack under engine.
Remove left engine support bolts from body.
Remove engine support plate bolts from engine.
Unbolt air conditioner pump and move it out of the way.
Get under vehicle and remove steering pump bolts and move it out of the way.
Remove 6 crankshaft pulley bolts, should be 12mm.
The engine support bracket shoud come off now.
Remove the main crankshaft bolt.
Remove crankshaft dampener.
Remove the timing cover bolts and take off the covers.
Take off the old belt & replace with a new one, don't use a previously used belt.
Make sure the belt tensioner is installed correctly.
Put all the stuff back on.
Get a Haynes manual, pages 3-41.

Posted on Jul 06, 2009

harley9701ha
  • 424 Answers

SOURCE: where is the mega fuse on a 96 ford contour GL and

The mega fuse is located to the rear of the engine near the firewall.It is inline. The best way to test it is to disconnect the battery and ohm the both sides of the fuse.

Posted on Aug 13, 2009

  • 784 Answers

SOURCE: 97 Ford Contour GL 2.5 L V6. Stalling out. Auto

They are not only for improving milleage, but play a crusual key for ECM to give out how much fuel to mix with air to have proper combustion hence not stalling when accelerated. But Oxygen sensors are expensive and even you have them replaced , this is not going to solve your problem since gum has built up at your throttle valve over the years. Have another shop to clean your throttle body first. Make an appointment so you can be there to see how dirty the throttle body is and also to make sure they actually take out the part to clean, not just spraying cleaner to the Air mass flow flap valve. After the throttle body cleaned, take off the battery cables for 30 minutes to reset the ECM to its default state so it doesn't use data from your current state. You will see an improvement. Afterward, the problem is still existing then Have Auto Zone store diagnose free for O2 problem before replacing them. Cheers.

Posted on Oct 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where do I find a crankshaft sensor on a 1999 Ford Contour 2.0


On a 1995 it is back by the transmission.
Its NOt on the head its low below the head rear of the engine
I included a picture from Google

  • thumb.gif

Nov 01, 2014 | 1999 Ford Contour

3 Answers

Where is the crank sensor on a 1994 ford taurus gl


What engine? 3.0 DOHC 3.0 OHV 3.8 liter

Apr 10, 2013 | 1994 Ford Taurus

1 Answer

Oil leak


Hi,
I'm not a mech and not familiar w/the Contour, but it's likely the oil pump or the oil sending unit/sensor. Also, could be the camshaft or crankshaft seals.

Autozone has online repair manuals for reference.

GL,
Td

Oct 01, 2012 | 1999 Ford Contour

1 Answer

I have a 95 ford contour can't get any spark . changed the spark plugs, fuel pump, and fuel filter, and air filter.


I'd suggest getting a chilton or Haynes book for your car first. Very handy! If no spark, you can test the coil with an ohmmeter, and test wires to it. Another possibility is wires to crankshaft position sensor shorted, or sensor is bad. This sensor tells computer when to fire, and if bad, you get no spark situation. Also check any fuses that have to do with ignition.

Jul 22, 2012 | 1995 Ford Contour

2 Answers

How to align cams on a 95 ford contour 2.0 dohc?


In order to time this engine you've got to align the cams with the respective markings on the new belt, this also pertains to the crankshaft pulley. If there are no markings on the belt, the camshaft markings will have a demarkation on the head two which each cam must be aligned. From here I cannot tell you where thes marks are but they are usually at 12:00 or 3:00 plus when you get near the alignment point the cams will feel almost like they are freewheeling for about 3/4- 1 inch in either direction.The crankshaft has to be at TDC or topdead center. this is easily accomplised with a 12 inch ruler laid across the front of the pulley with the long side facing up. This way you can center the mounting bolt and the timing mark at the same time, assuring you of exact center alignment. That's about all I can offer. Thank you, Dana. P.S. please do not turn the engine over with the key until you are certain that all three marks are dead on target. You may however turn it over by hand using a socket of the correct size going clockwise on the crankshaft.

Sep 06, 2009 | 1995 Ford Contour

2 Answers

How do you change the water pump on a 1998 Ford contour 2.0 liter. have the part off but can't get it out of engine compartment


Removal
  1. NOTE: Install the memory saver.
    Disconnect the battery ground cable.
  1. Drain the cooling system. Refer to Cooling System Draining, Filling and Bleeding in this Section.
  1. Remove the wheel.
  1. Remove the right - hand side lower splash shield.
    1. Remove the bolts.
    1. Remove the splash shield.
    v2401032.jpg
  1. Lower the vehicle.
  1. Loosen the water pump pulley bolts.
    v2401027.jpg
  1. Remove the accessory drive belt. For additional information, refer to Section 303-05.
  1. Using the special tool, remove the crankshaft pulley.
    e0008816.jpg
  1. Remove the water pump pulley.
    1. Remove the bolts.
    1. Remove the pulley.
    v2401028.jpg
  1. Remove the water pump bolts.
    v2401029.jpg
  1. NOTE: Water pump must be turned 180° to remove from the vehicle.
    Remove the water pump.
    gq0214a.jpg

Apr 27, 2009 | Ford Contour Cars & Trucks

1 Answer

Needing schematics for timing belt on a 2000 se


Removal & Installation

2.0L Engine
  1. Remove or disconnect the following:

    Negative battery cable Spark plugs Catalytic converter Right front wheel Right inner splash shield Accessory drive belt and idler pulley
  2. Rotate the crankshaft to Top Dead Center (TDC) and install Crankshaft TDC Timing Peg T97P-6000-A.
  3. Rotate the crankshaft clockwise against the peg.
  4. Remove or disconnect the following:

    Water pump pulley Valve cover Crankshaft pulley Timing belt covers
  5. Install Camshaft Alignment Timing Tool T94P-6256-CH into theslots of both camshafts at the rear of the cylinder head to lock thecamshafts into position.
  6. Loosen the timing belt tensioner bolt and relieve the tension onthe timing belt by disconnecting the tensioner tab from the timingcover back plate.
  7. Remove the timing belt.

    0900c152801e2a75.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Crankshaft alignment position-Ford 2.0L (VIN 3) engines


    0900c152801e2a76.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Placement of Camshaft Alignment Timing Tool T94P-6256-CH-Ford 2.0L (VIN 3) engines


    0900c152801e2a77.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Timing belt tensioner index marks-Ford 2.0L (VIN 3) engines

To install:

NOTE Always replace the timing belt after loosening or removing it.
  1. Install the timing belt.
  2. Engage the timing belt tensioner tab into the timing cover back plate.
  3. Adjust the timing belt tensioner until the index marks are aligned. Tighten the tensioner bolt to 17-20 ft. lbs. (22-28 Nm).
  4. Remove the camshaft alignment tool and the crankshaft TDC peg.
  5. Install or connect the following:

    Timing belt covers Crankshaft pulley. Tighten the bolt to 81-89 ft. lbs. (110-120 Nm). Valve cover Water pump pulley Accessory drive belt and idler pulley Right inner splash shield Right front wheel Catalytic converter Spark plugs Negative battery cable
  6. Start the engine and check for proper operation.

Apr 08, 2009 | 2000 Ford Contour

1 Answer

1995 Ford Contour GL, 4-Liter transmission problems


check the transmission fluid level first and also when was last time you had a tranny service new fluid and filter because the screen could be plugged and not allowing the fluid to get to the torque converter also have the catalytic converter checked out

Nov 24, 2008 | 2000 Ford Contour

1 Answer

1995 FORD Contour GL V6 AUTO ; Trans.> speed sensor prob.


The speed sensor signal goes through the speedo cluster and then to the PCM, this is the main computer that controls trans and engine functions, in order to see if the PCM is getting the speed sensor signal you need to install what we call a break out box to monitor the signal and see where it is being lost, it could be the connector ar the transmission, pull it off and make sure the wires are not broken inside the insulation near the connector plastic shell, There is no way to fix this without these checks.

Sep 11, 2008 | 1995 Ford Contour

Not finding what you are looking for?
1995 Ford Contour Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...