Question about Chevrolet Silverado 1500

1 Answer

Engine light has turned on, computer dianostic indicates knock sensor. Knock sensor replaced by chevrolet dealer on april of 2010.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 170 Answers

I recently had the same problem but with a different make and model vehicle. I replaced the Cam Shaft Sensor and that took care of the problem. Contact the dealer i'm sure it should still be under warranty, also they have the necessary tools to check if the sensor is sending the right pulses while running. Good Luck.

Posted on Sep 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code p0325


P0325 Knock Sensor 1 Circuit Malfunction
A knock sensor tells the engine computer when one or more of your engine's cylinders are "knocking", that is, exploding the air/fuel mixture in a way that delivers less power and can be damaging to the engine if prolonged.
The computer uses this information to tune the engine so that it doesn't knock. If your knock sensor wasn't operating properly, so that it was always indicating a knock, the engine computer's response may have been to change the ignition timing on your engine. Knock sensors generally bolt into or thread into the engine block. This P0325 code may show up intermittently or the Service Engine light may be lit constantly. Other knock sensor related DTC codes include P0330.
Symptoms You may notice drivability problems including a lack of power and perhaps some hesitation. There may also be other symptoms.
Causes A code P0325 most likely means one or more of the following has happened:
  • The knock sensor is faulty and needs to be replaced
  • There is a wiring short/fault in the knock sensor circuit

Nov 20, 2016 | Cars & Trucks

1 Answer

Location of knock sensors for 2010 Chevy equinox


on the front of the engine block its round with the securing bolt going through it and it will have a black lead coming from it

Jun 19, 2016 | 2010 Chevrolet Equinox

1 Answer

2010 Kia Sedona rattle in front when accelerating


As the dealer was unable to find anything, it's possible that this could be normal operation.

All modern auto engines will knock under heavy acceleration; could you be confusing engine knock with "vibration"? (The knock is by design to allow the knock sensor to determine how lean to set the computer. This can be changed by a change of gasoline to a different brand or different grade. Don't run mid grade ot hi-test for more than one tankfull if your car calls for 87 octane however.)

In that the light came on (and off), will set a code in the computer that the dealer can read. Take it back to the dealer and tell him the history. He will be able to read the error and narrow down the cause.

Feb 24, 2014 | 2010 Kia Sedona

2 Answers

GMC 4.3L DTC P0330 flashing MIL


P0330 - Knock Sensor 2 Circuit Malfunction (Bank 2)
A knock sensor tells the engine computer when one or more of your engine's cylinders are "knocking", that is, exploding the air/fuel mixture in a way that delivers less power and can be damaging to the engine if prolonged. The computer uses this information to tune the engine so that it doesn't knock. If your knock sensor wasn't operating properly, so that it was always indicating a knock, the engine computer's response may have been to change the ignition timing on your engine. Knock sensors generally bolt into or thread into the engine block. This P0330 code may show up intermittently or the Service Engine light may be lit constantly. Other knock sensor related DTC codes include P0325.

Symptoms: You may notice drivability problems including a lack of power and perhaps some hesitation. There may also be other symptoms.

Causes: A code P0330 most likely means one or more of the following has happened:
The "B" knock sensor is faulty and needs to be replaced
There is a wiring short/fault in the knock sensor circuit

Possible Solutions:
Check the resistance of the knock sensor on bank 2 (compare it to factory specs)
Check for broken/frayed wires leading to the sensor
Replace the knock sensor on bank 2


Hope helps.

Aug 23, 2011 | GMC Safari Cars & Trucks

1 Answer

I have a code p0325 knock sensor 1, circuit bank 1 or single sensor problem


A knock sensor tells the engine computer when one or more of your engine's cylinders are "knocking", that is, exploding the air/fuel mixture in a way that delivers less power and can be damaging to the engine if prolonged. The computer uses this information to tune the engine so that it doesn't knock. If your knock sensor wasn't operating properly, so that it was always indicating a knock, the engine computer's response may have been to change the ignition timing on your engine. Knock sensors generally bolt into or thread into the engine block.

This P0325 code may show up intermittently or the Service Engine light may be lit constantly. Other knock sensor related DTC codes include P0330.

Symptoms: You may notice drivability problems including a lack of power and perhaps some hesitation. There may also be other symptoms.

Causes: A code P0325 most likely means one or more of the following has happened:
* The knock sensor is faulty and needs to be replaced
* There is a wiring short/fault in the knock sensor circuit

Possible Solutions
* Check the resistance of the knock sensor (compare it to factory specs)
* Check for broken/frayed wires leading to the sensor
* Replace the knock sensor


Test it and tell us news.

Mar 15, 2011 | 1999 Nissan Maxima

1 Answer

I have a 04' Chev, 6.0L. Engine light came on, fault code came up PO332. I'm afraid the KS's are under the intake. Is there any way to test the KS to see if it is bad, or is there another problem that is...


P0332 - Knock Sensor 2 Circuit Low Input (Bank 2)

The knock sensor is attached to the cylinder block. It senses engine knocking using a piezoelectric element. A knocking vibration from the cylinder block is sensed as vibrational pressure. This pressure is converted into a voltage signal and sent to the Powertrain Control Module (PCM) or Engine Control Module (ECM).

Causes for P0332 DTC:
- Knock sensor circuit short to GND.
- Knock sensor circuit short to PWR.
- Knock sensor circuit open.
- Damaged knock sensor.
- PCM or ECM failure.

Solutions:
- Repair or resecure the harness or connector.
- Replace the knock sensor.

Your best bet is to just replace the knock sensor for sensor 2 bank 2. Call Auto Zone with part number SU1282 this is the OEM replacement.

The knock sensor looks like this:

101_lmar_8.jpg


moz-screenshot.pngmoz-screenshot-1.png

Mar 09, 2011 | 2004 Chevrolet Silverado 2500 Crew Cab

3 Answers

Diagnostic code po325 what does this mean


Hi the error code relates to the PCM Knock Sensor Circuit

A knock sensor tells the engine computer when one or more of your engine's cylinders are "knocking", that is, exploding the air/fuel mixture in a way that delivers less power and can be damaging to the engine if prolonged. The computer uses this information to tune the engine so that it doesn't knock. If your knock sensor wasn't operating properly, so that it was always indicating a knock, the engine computer's response may have been to change the ignition timing on your engine. The knock sensor generally threads into the engine block. This P0325 code may show up intermittently or the Service Engine light may be lit constantly.
Symptoms

You may notice drivability problems including a lack of power and perhaps some hesitation. There may also be other symptoms.
Causes

A code P0325 most likely means one or more of the following has happened:

* The knock sensor is faulty and needs to be replaced
* There is a wiring short/fault in the knock sensor circuit

Possible Solutions

* Check the resistance of the knock sensor (compare it to factory specs)
* Check for broken/frayed wires leading to the sensor
* Replace the knock sensor

Hope this helps
Steve

Mar 03, 2011 | 1993 Jeep Grand Cherokee

1 Answer

I have a 2004 pilot, VTS4 and engine light came on. i have a p0325 knock sensor circ. bank A. just replace the sensor?? also i can seem to find any diagrams. any help appreciated!!!


It does sound like the sensor may be bad, but you also need to check the wiring.
This information comes from:

http://www.obd-codes.com/p0325

P0325 OBD-II Trouble Code Technical Description

Knock Sensor Circuit Malfunction
What does that mean?

A knock sensor tells the engine computer when one or more of your engine's cylinders are "knocking", that is, exploding the air/fuel mixture in a way that delivers less power and can be damaging to the engine if prolonged. The computer uses this information to tune the engine so that it doesn't knock. If your knock sensor wasn't operating properly, so that it was always indicating a knock, the engine computer's response may have been to change the ignition timing on your engine. Knock sensors generally bolt into or thread into the engine block. This P0325 code may show up intermittently or the Service Engine light may be lit constantly. Other knock sensor related DTC codes include P0330.
FB.init("dd7d9e9681341cde77587bc6a2029f6f"); OBD-Codes.com on Facebook Symptoms

You may notice drivability problems including a lack of power and perhaps some hesitation. There may also be other symptoms.
Causes

A code P0325 most likely means one or more of the following has happened:

Possible Solutions
  • Check the resistance of the knock sensor (compare it to factory specs)
  • Check for broken/frayed wires leading to the sensor
  • Replace the knock sensor

Mar 02, 2011 | Honda Pilot Cars & Trucks

1 Answer

My car pulled p0328 code what does that mean


thanks, that helps. It could be that is the only problem. The knock sensors started being installed several years back to provide performance feed back to the ECM/PCM. If a cylinder doesn't fire the knock sensor reports a misfire to the computer and a misfire code is shown. In this event the sensor is returning a value that indicated to the computer it was not functioning correctly. Replacement of this sensor doesn't require the motor to be rebuilt should cost around $200 at a dealer maybe a little more. You can view the knock sensor a little like the O2 sensor with the main difference being that if the knock sensor doesn't work correctly it could cause the vehicle to computer to adjust your timing the wrong way.

Jul 20, 2010 | 2008 Chevrolet Cobalt

1 Answer

Knock engine sensor light on truck is hesitating/


Did they replace the knock sensor?Check the wire going to the sensor(knock).Look for a bare place hiting up against something ,grounding it out.Make sure the plug to knock sensor is good.And make sure it is making a good connection,Knock sensors also ground a part of the computer to feed back imformation.This connection is a must,the truck will not perform at all,stumble,miss,and carry on.Sometimes even backfire.If they did not replace the knock sensor,replace it with high quality sensor from NAPA,or oem from dealer.This sensor has to be made perfect,no room for inperfection.The knock sensor is easy to replace,they just screw in a hole in the block.When removing the sensors,nothing will come out such as oil or water,this is a dry threaded hole.It is a bell shaped sensor.If you don`t know which sensor is bad,purchase one.replace one,and if there is no change,replace the other side with the old sensor you just took out,it will be a good one.I hope this helps you,Let us know if it does.

Oct 05, 2009 | 2000 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...